Albatron PM800 Pro (V2.0) Manual de usuario

PM800 Pro (V2.0)

All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed,

stored in a retrieval system or translated into any language or computer language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the

prior written permission of the company. Brands and product names are trademarks or registered

trademarks of their respective companies.

The vendor makes no representations or warranties with respect to the contents herein and especially

disclaim any implied warranties of merchantability or fitness for any purpose. Further the vendor

reserves the right to revise this publication and to make changes to the contents herein without

obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not

allowed without first obtaining the vendor’s approval in writing.

Disclaimer

We make no warranty of any kind with regard to the content of this user’s manual. The content is

subject to change without notice and we will not be responsible for any mistakes found in this user’s

manual. All the brand and product names are trademarks of their respective companies.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense. However, there is no guarantee that interference will not occur in a

particular installation.

Ver:EG100

You have to know !!!

0The images and pictures in this manual are for reference only and may vary

slightly from actual product installation depending on specific hardware

models, third party components and software versions.

0Unplug your computer when installing components and configuring switches

and pins.

0This mainboard contains very delicate IC chips. Use a grounded wrist strap

when working with the system.

0Do not touch the IC chips, leads, connectors or other components.

0Unplug the AC power when you install or remove any device on the

mainboard.

Package Contents

PM800 Pro(V2.0) mainboard

IDE Cable/ FDC Cable

USB Bracket (optional)

SATA Power cord (optional)

SATA Cable (optional)

Installation and Setup Driver CD

PM800 Pro(V2.0) User Manual

Symbols

Attention …

Following the procedures …

Troubleshooting …

Please refer to …

PM800 Pro(V2.0)

VIA®PM800 & VT8237

Supports Socket 478 Intel®Pentium®4

(Willamette/ Northwood/ Prescott) Processor

User Manual

Enabling Hyper-Threading for your computer system requires ALL of the

following components

zCPU: An Intel®Pentium®4 Processor with HT Technology

zChipset: An Intel®Chipset that supports HT Technology

zBIOS: A BIOS that supports HT Technology must be enabled

zOS: An operating system that supports HT Technology

For more information on Hyper-Threading Technology, go to:

http://www.intel.com/info/hyperthreading

Dimensions (Micro-ATX form-factor):

z199mm x 244mm (WxL)

Operating System:

zSupports most popular operating systems: Windows®9X/ME/2000/XP etc.

Contents

CHAPTER 1. GETTING STARTED ............................................................2

INTRODUCTION..........................................................................................................2

SPECIFICATION..........................................................................................................3

Hardware Installation ...........................................................................................7

CPU Processor Installation...................................................................................7

Memory Installation .............................................................................................8

Back Panel Configuration.....................................................................................9

Front Panel Indicator: SW/LED、PWRLED、SPEAKER ...............................11

Headers & Jumpers.............................................................................................13

Audio Connectors...............................................................................................14

Slots....................................................................................................................14

Power Supply Attachments.................................................................................15

CHAPTER 2 SOFTWARE SETUP.............................................................15

SOFTWARE LIST ......................................................................................................15

APPENDIX I: SUPER 5.1 CHANNEL SETUP ...............................................................16

PM800 Pro(V2.0)

Chapter 1. Getting Started

Introduction

Congratulations on choosing the PM800 Pro(v2.0) mainboard !These are based on the VIA® PM800

Northbridge chipset and the VIA® VT8237 Southbridge chipset. It supports Intel® Pentium® 4

(Willamette/ Northwood/ Prescott) Processors with a FSB (Front Side Bus) frequency of 400/ 533/ 800

MHz.

The PM800 Pro(V2.0) provide 2 DIMM sockets using 184 pin DDR SDRAM with a total capacity of up to

2GB. You can install unbuffered & non-ECC DDR400/ 333/ 266 (PC3200/ 2700/ 2100) DDR SDRAM.

The PM800 Pro(V2.0) provide one 8X/ 4X (AGP 3.0/ 1.5V or 0.8V ) AGP slot.

The PM800 Pro(V2.0) include built in IDE facilities that support Ultra DMA ATA 66/100/133 and PIO

Modes. It also includes built in Serial ATA facilities that support SATA RAID 0 or RAID 1 and transfer rate

to 150 MB/s per channel.

The PM800 Pro(V2.0) also come with a AC’97 Sound Codec which supports high quality 6 channel audio

(Super 5.1 Channel Audio Effect). It also supports Sony/ Philips Digital Interface (Optional).

The PM800 Pro(V2.0) also comes with a LAN PHY chip (VIA VT6103L)) and provides a back panel LAN

port capable of 1/ 10/ 100 Mbit/s transmission speeds.

The PM800 Pro(V2.0) support eight USB 2.0 ports and also include an infrared header.

All of the information in this manual only for reference. This specification is subject to change without

notice.

PM800 Pro(V2.0)

Specification

CPU:

zSupports Socket 478 Pentium®4 processor

zSupports Hyper-Threading Technology

Speed:

z400/ 533/ 800 MHz Front Side Bus frequencies

z33 MHz, 32 bit PCI interface (PCI 2.2 compliant)

z66 MHz AGP 3.0 compliant interface that supports 8X/ 4X data transfer modes (only supports

0.8V/ 1.5V)

Chipset:

zNorthbridge Chipset – VIA® PM800

zSouthbridge Chipset – VIA® VT8237

zI/O Controller –ITE IT8705

zAC’97 Codec – Realtek ALC655

zLAN Controller – VIA® VT6103L

DRAM Memory:

zSupports DDR400 (PC3200)/ DDR333 (PC2700)/ DDR266 (PC2100) SDRAM

zSupports 64 MB/ 128 MB/ 256 MB/ 512 MB/ 1 GB unbuffered & non-ECC DIMM

zSupports memory modules with a total capacity of 2 GB (see memory installation section for

more details)

Green Functionality:

zSupports Phoenix-Award BIOS ™ power management functionality

zWakes from power saving sleep mode with any keyboard or mouse activity

Shadow RAM:

zThis mainboard is equipped with a memory controller providing shadow RAM and support for

ROM BIOS

PM800 Pro(V2.0)

BUS Slots:

zAGP slot (8X/ 4X, 1.5V or 0.8v) x 1

zPCI bus slot x 3

zCNR bus slot x 1 (Optional)

Flash Memory:

zSupports flash memory functionality

zSupports ESCD functionality

Hardware Monitor Function:

zMonitors CPUFAN/ CHASFAN Speeds

zMonitors system Voltage

Infrared:

zSupports IrDA Version 1.0 SIR Protocol with a maximum baud rate of up to 115.2 Kbps

zSupports SHARP ASK-IR Protocol with maximum baud rate of up to 57600 bps

AC’97 Sound Codec Onboard:

zAC-LINK protocol compliance

zCompliant with AC’97 2.1 specification

z6-channel playback capability (super 5.1 Channel Audio Effect)

zSupports (S/PDIF) Sony/ Philips Digital Interface (Optional)

VIA VT6103L LAN Controller on board

z1/10/100 MHz full and half duplex operation

zIndependent 2K byte FIFOs for receive and transmit

zMagic packet and wake-on-address filtering

zSoftware controllable power down

Universal Serial Bus:

zSupports up to eight USB ports for USB interface devices

zSupports USB 2.0 Enhanced Host Controller Interface (EHCI) and USB 1.1 Universal Host

Controller Interface (UHCI)

PM800 Pro(V2.0)

Onboard Video Graphic Acceleration:

zSupports 2D Acceleration

zSupports 3D Acceleration

zSupports Video Acceleration

zMicorsoft® DirectX compatible

zOpenGL dreiver available

I/O facilities:

zOne multi-mode Parallel Port capable of supporting the following specifications:

Standard & Bi-direction Parallel Port

Enhanced Parallel Port (EPP)

Extended Capabilities Port (ECP)

zSupports one serial ports, 16550 UART

zSupports one VGA port

zSupports PS/2 mouse and PS/2 keyboard

zSupports 360 KB, 720 KB, 1.2 MB, 1.44 MB, and 2.88 MB floppy disk drives

IDE Facilities:

zSupports Ultra ATA 66/ 100/ 133, DMA and PIO modes

zSupports IDE interface with CD-ROM

zSupports high capacity hard disk drives

zSupports installation of up to 4 drives, with separate IDE connections for Primary and

Secondary connectors

Serial ATA Controller:

zCompatible with SATA Spec 1.0

zSupports Serial ATA 150 MB/sec transfers

zSupports RAID 0 or RAID 1 software with this controller

BIOS:

zPhoenix-Award™ BIOS

zSupports APM1.2

zSupports ACPI2.0 power management

PM800 Pro(V2.0)

Watch Dog Timer:

zThis mainboard contains a special feature called the “Watch Dog Timer” which is used to

detect when the system is unable to handle over-clocking configurations during the POST

stage. Once a problem is detected the system will reset the configurations and reboot the

system after five seconds. Configuration

Layout of PM800 Pro(V2.0)

BIOS

BAT1

FDD1

CODEC

Super I/O

IT 8705

PM 800

VT 8237

VT8237R

CPU1

CODEC

Socket 478

EFG HIJ

LAN

PHY

PM800 Pro(V2.0)

A. Rear (back) side connectors. J. JPANEL1: Front Panel headers.

B. JAUDIOIN1: Front side audio out

header. (Optional) K. JCMOS1: Clear CMOS header.

C. JCDIN1: CD-In connector. L. JCI1: Chassis open header.

D. JSPDIF1: Digital Audio connector.

(Optional) M. JSATA1~2: Serial ATA connectors.

E. CNR1: Communication Network Riser

slot. N. AGP1: Accelerated Graphics Port slot.

F. PCI1~3: Peripheral Component

Interconnect slots. O. IDE1~2: Hard Disk connectors.

G. FDD1: Floppy Disk connector. P. DIMM1~2: DDR DIMM modules.

H. JSFAN1: System Fan header. Q. JATXPWR1~2: ATX Power Source

connectors.

I. JUSB3~4: Front side USB headers. R. JCFAN1: CPU Fan header.

Hardware Installation

This section will assist you in quickly installing your system hardware. Wear a wrist ground strap before

handling components. Electrostatic discharge may damage your system components.

CPU Processor Installation

This mainboard supports Intel®Pentium®4 processors using a Socket 478. Before building your system,

we suggest you visit the Intel website http://www.intel.com and review the processor installation

procedures.

CPU Socket 478 Configuration Steps:

1.Locate the CPU socket on your mainboard and nudge the lever away from the socket. Then lift the

lever to a 90-degree angle.

2.On the socket, locate the corner that has the pin-1 receptor. This corner will be near to the end of

the lever. Match the dot on the CPU with the pin-1 receptor on the socket and lower the CPU onto

the s ket. The b e of the socket.

oc ottom of the CPU should be flush with the fac

3until it snaps back into position. This will lock down the CPU.

.Lower the lever

Pin1 Receptor

Dot

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Albatron

Albatron

Albatron PX925XE Series Manual de usuario

Albatron

Albatron PXP965 (V2.0) Manual de usuario

Albatron

Albatron K8X890 Series Manual de usuario

Albatron

Albatron KX18D PRO II Manual de usuario

Albatron

Albatron PI852 Manual de usuario

Albatron

Albatron KI51PV-754 Manual de usuario

Albatron

Albatron PX915-DV Manual de usuario

Albatron

Albatron K8M800-754 Series Manual de usuario

Albatron

Albatron K8X250 Manual de usuario

Albatron

Albatron K8X250GB PRO Manual de usuario

Albatron

Albatron PX865PEC PRO(2.0) Manual de usuario

Albatron

Albatron KX550 Manual de usuario

Albatron

Albatron KM400T-8X Series Manual de usuario

Albatron

Albatron KM7025 Manual de usuario

Albatron

Albatron PXP35 Manual de usuario

Albatron

Albatron PX915P-2V Manual de usuario

Albatron

Albatron P4M800 Pro Manual de usuario

Albatron

Albatron PM73V Manual de usuario

Albatron

Albatron PXP43 Manual de usuario

Albatron

Albatron PX915PC PRO-G Manual de usuario

Albatron

Albatron PM945GZ Manual de usuario

Albatron

Albatron PM915-478 Manual de usuario

Albatron

Albatron PM 845G Series Manual de usuario

Albatron

Albatron KX400+ Pro-C Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario