AirLive WLA-5200AP Manual de usuario

Quick Setup Guide

WLA

5200AP

802.11a/b/g Multi-function

Wireless Access Point

English ●●●

Deutsch ●●●

Česky ●●●

Русский ●●●

Português ●●●

Españoll●●●

Slovensky ●●●

Polski ●●●

English

802.11 a/b/g Wireless AP

WLA

00AP

LED Status

Meaning Solid Flashing

Power Turns solid green when power

is ON N/A.

LAN1/LAN2 LAN Connection is detected. Receiving/

Sending data

Wireless Wireless Connection is made Receiving/

Sending data

Important Information

English



support 6 modes of wirless functions :

AP, Client, Bridge,WDS Repeater,Universal Repeater,

WISP(Client Router)



All modes (AP,Client,Repeater,WISP) default IP is 192.168.1.254



The Default mode is set to AP mode



The default Subnet Mask is 255.255.255.0



The default user name , password , SSID is set to “airlive”



The DHCP server default is on in WISP mode, other mode is set to off



The Wireless mode default is 802.11a mode running in 5Ghz.



When click the each Wireless mode button to change each Wirelees

mode, system will reboot to take effect

LED Indicators

Ports and Connectors

zReset: Press 10 seconds to

restore settings to factory default

zLAN1/LAN2: Connect your PC,

Switch, or Router here.

zPower: Connect the included

Power adapter here.

zAntenna: Install Antenna Here

English

802.11 a/b/g Wireless AP

WLA

00AP

Installation Steps

1. Please install your network cards first before the AP

2. Screw-in the antenna (clockwise) into the Antenna connector

3. Connect the power and LAN cable to the back

4. Use your wireless card to do a site survey, the default SSID is airlive

5. If you need to change AP’s configuration, please follow the procedure

below:

The Client mode’s default IP address is 192.168.1.254 Please

make sure your computer IP is in the same subnet as the AP (i.e.

192.168.1.x)

Open the web browser and enter 192.168.1.254

Enter the default user name airlive and password “airlive”

English

Wireless mode setting

This page includes all primary and major parameters for wireless mode

setting. Any parameter change will cause the device to reboot for the new

settings to take effect.

Wireless Mode: AP, Client, Bridge, Repeater , WISP mode

The default is set to AP mode. you can select to change it to other modes. .

Network Type: When in Client mode, you can select between Ad-Hoc

andInfrastructure

Repeater Type: When in Repeater mode, you can select between

WDS Repeater and Universal Repeater

WISP Type: When in WISP mode, you can setup WISP(Client Router)

English

802.11 a/b/g Wireless AP

WLA

00AP

Client, Bridge mode setup

Bridge Mode

Device B:

Mode: Bridge

Device A:

Mode: Bridge

Please make sure both A and B are set to the same channel

Client Mode

Device B:

WISP Outdoor AP

Network Type: Infrastructure

Device A:

Mode: Client

Please make sure both A and B are set to the same ESSID and channel

English

802.11 a/b/g Wireless AP

WLA

00AP

Device A:

Mode: WDS Repeater

Mac Address: Device B’s AP

Mac Address

WDS Repeater mode setup

Device B:

WDS Wireless AP/ Router

Mac Address: Device A’s AP Mac

Address

WDS Repeater Mode

1. Please make sure both A and B are set to the same channel number

2. Add other’s AP MAC Address(BSSID) that the Repeater want to connect

(Please make sure remote wireless AP/Router support WDS function)

3. Setup Wireless security function (Repeater->Security->Setup)

between WDS repeater and Wireless Client use same authentication

and encryption for wirless LAN connection. For details,please refer the

user’s manual

English

802.11 a/b/g Wireless AP

WLA

00AP

Universal Repeater Mode

Device B:

Wireless Router

Universal Repeater doesn’t require the remote device to have WDS function

Universal Repeater setup

Device A:

Mode: Universal Repeater

1. Please make sure both A and B are set to the same channel number

2. type the other AP/Router’s SSID in the “SSID of Extended Interface”

field that the repeater want to connect.

Note: the device SSID and the SSID of extended interface can be the same

or different. When you are using the universal repeater mode,

please make sure the remote AP/Router WDS function is turned off..

WISP Mode (Client Router)

Device B: WISP outdoor AP

Device A:

Mode: WISP (Client Router)

WISP mode setup

English

802.11 a/b/g Wireless AP

WLA

00AP

1. please click the “Site Survey” buttion to search and connect the WISP

Outdoor AP device

2. in WISP mode,please click the WAN port setup button for WAN

port configuration,choose the WAN Access Type and type some

Information in other filed. For details,please refer the user’s manual.

English

802.11 a/b/g Wireless AP

WLA

00AP

Select 802.11a, b, or g mode

The AP is default to 802.11a mode, running in 5Ghz

spectrum. If you want to run it in 802.11b/g mode, you

need to change the settings. The AP can not run in both

802.11a and 802.11g mode simultaneously.

1. Open your web browser and enter the AP’s IP address.

2. Select Mode, and choose which wireless mode you want

3. for example, the default mode is AP mode and default band is 11a

(outdoor), you can click the setup button and choose the 11b,

11g,11a (indoor), or 11g+b mixed to change the 2.4Ghz or 5Ghz

band.

4. Click on Apply chnages to finish the setting

802.11a Frequency Domain

If you want to change the 802.11a chnnael ,please follow the steps below:

1. the default Region is Europe , if you are not in this region, please

change the Region first.

2. go to the Wireless mode, select the mode you want ,click the setup

button and choose the 11a (outdoor) or 11a (indoor)

3. in the Channel Number field, you just can choose the 11a channel

you want

4. click the “Apply Changes” and take the effect

Note: please refer the user’s manual for detail settings.

Please check with your local authority about the

frequency range that you can use legally.

Please do not use the fequency range that is not allowed in

your country.

English

802.11 a/b/g Wireless AP

WLA

00AP

zIndoor: 5.18 to 5.32GHz

zOutdoor: 5.50 to 5.7GHz

Your AP comes with the above frequency bands open. If you are using

802.11a mode in Czech and Slovakia countries, please do not use “auto”

channel selection. Please choose your frequency channel according to the

instruction below:

zIndoor: Channel 36, 40, 44, 48, 52, 56, 60, 64

zOutdoor: Channel 100, 104, 108, 112, 116, 120, 124, 128, 132,

136, 140

MEMO

English

802.11 a/b/g Wireless AP

WLA

00AP Deutsch

LED Status

Bedeutung an

Bedeutung

Power Leuchet grün wenn die

Stromversorgung aktiv ist Power

LAN1/LAN2 LAN-Verbindung erkannt. LAN1/LAN2

Wireless Wireless-Verbindung

hergestellt Wireless

Wichtige Informationen

Werkseitige Voreinstellungen:

Unterstützt 6 Wireless-Funktionsmodi:

AP, Client, Bridge, WDS-Repeater, Universal-Repeater,

WISP(Client-Router)



IP-Adresse aller Modi (AP,Client,Repeater,WISP): 192.168.1.254



Modus: AP



Subnetzmaske: 255.255.255.0



Benutzername, Passwort und SSID: “airlive”



DHCP-Server: on im WISP-Modus; andere Modi: off

Wireless-Modus: 802.11a, 5 Ghz



Nach Änderung des Wirelessmodus durch einen Klick auf den hierzu

vorgesehenen Button erfolgt ein Neustart des Systems.

LED-Anzei

Anschlüsse und Schalter

zReset: Stellt nach 10-sekundigem

gedrückt halten die

Werksvoreinstellungen wieder her

zLAN1/LAN2: Zum Anschluss eines

PC, Switch, Router, etc.

zPower: Schließen Sie das

mitgelieferte Netzteil hier an.

zAntenne: Schließen Sie hier die

Antenne an

Deutsch

Tabla de contenidos

Idiomas:

Otros manuales de Punto de acceso inalámbrico de AirLive

AirLive

AirLive WHP-1100 Manual de usuario

AirLive

AirLive Air Live WL-5470AP Manual de usuario

AirLive

AirLive WL-5470POE Manual de usuario

AirLive

AirLive WLA-500AP Manual de usuario

AirLive

AirLive WHA-5500CPE Manual de usuario

AirLive

AirLive N.Plug Manual de usuario

AirLive

AirLive WLA-5000AP Manual de usuario

AirLive

AirLive WL-5460AP v2 Manual de usuario

AirLive

AirLive N.Plug Manual de usuario

AirLive

AirLive WT-2000AP Manual de usuario

AirLive

AirLive N.TOP Manual de usuario

AirLive

AirLive AC.TOP Manual de usuario

AirLive

AirLive AIRMAX2 Manual de usuario

AirLive

AirLive WMU-6000FS Manual de usuario

AirLive

AirLive WH-5420CPE Manual de usuario

AirLive

AirLive WH-5420CPE Manual de usuario

AirLive

AirLive WMM-3000AP Manual de usuario

AirLive

AirLive AIRMAX5 Manual de usuario

AirLive

AirLive WH-9200AP Manual de usuario

AirLive

AirLive WT-2000AP Manual de usuario

AirLive

AirLive WH-9200AP Manual de usuario

AirLive

AirLive AirMax5X II Manual de usuario

AirLive

AirLive AIRLIVE WL-5430AP Manual de usuario

AirLive

AirLive WHA-5500CPE Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario