Aidapt VP176 Manual de programación

Aluminium 4-Wheeled Rollator

Usage and Maintenance Instructions

Usage and Maintenance Instructions Ver.3 09/2013 (2634)

INTRODUCTION

Thank you for choosing the Aidapt Four-Wheeled Rollator.

Our four-wheeled rollator, as with all our products, is manufactured from high-quality

materials.

N.B. This equipment must be installed by a competent person.

VP 76/VP 76A/VP 76AB Red Aluminium Rollator 32 kg (2 st.) weight limit

VP 77/VP 77A/VP 77AB Blue Aluminium Rollator 32 kg (2 st.) weight limit

VP 78/VP 78A/VP 78AB Silver Aluminium Rollator 32 kg (2 st.) weight limit

Do not exceed the weight limit stated – doing so could put the user at risk.

INTENDED USE

our Aidapt Rollator has been designed to assist you when walking and carrying small items

of shopping using the bag provided. The bag was designed specifically to fit your rollator,

please only use the bag supplied for your Aidapt Rollator. Do not use or combine bags and/

or baskets from other manufacturers.

When not in use, you can simply fold the Aidapt Rollator and store away until you require it

next. The Aidapt range of tri-walkers and rollators are designed to be used both inside and

outside the home.

FEATURES

•User friendly loop brakes with lock

•Simple brake cable adjustment

•Soft plastic solid wheels

•Swivelling front wheels

•Folding locking mechanism

•Height adjustable

•User friendly ergonomic side locking

wheels for height adjustment

•Ergonomic handgrips to reduce pressure

Fig.

ASSEMBLY INSTRUCTIONS

1. Carefully remove all packaging, including the cardboard tubes covering the

knurled tube part of the brake assembly. Check the product thoroughly for damage

or obvious faults.

If you suspect the unit to be faulty, please do not use, but contact your

supplier immediately for service.

Usage and Maintenance Instructions Ver.3 09/2013 (2634)

2. Extend the rollator fully , and check that the side bars are straight and level.

Carefully insert the brake assembly with pre-punched extension tube (Fig. 3) within

the frame.

3. At the required height (there are several holes) insert the fixing screw through the

hexagonal hole in the frame, and pass through the hole in the handlebar tube,

place the curved plastic washer over the end of the screw, with the curved side

facing the tube. Fix the screw in place with the locking handwheel (Fig. 3b).

4. Make sure that the handwheel is tightened sufficiently so that the brake tubes will

not move accidentally.

5. After setting the height, check that both brakes are even in height and that the

rollator is sitting even onto the ground.

6. Fix the brake cables into the integral brake cable ‘U’ clip welded onto the frame if

not already assembled (Fig. 3a).

7. Prior to use make sure brakes are adjusted correctly and working properly. See

section ‘OPERATING THE BRAKES’ and ‘ADJUSTMENT’.

Fig. 3 Fig. 3a

Fig. 3b

Usage and Maintenance Instructions Ver.3 09/2013 (2634)

CENTRAL LOCKING MECHANISM AND USE

1. Open out the Rollator frame by pulling the cross bars outwards in opposite

directions forming an inverted ‘V’ with the main frame (Fig. 4).

2. Ensure that your Rollator is fully extended, and check that the side bars are straight

and level (Fig. 5).

Fig. 4 Fig. 5

PADDED BACK

1. To install the half round padded back first line up the ends of the tubular back with

the locating points (Fig. 6 and Fig. 7).

2. Ensure that the back properly clicks and locks into position, test by lifting up onto

the padded section of the half round back seat (Fig. 6).

Fig. 6 Fig. 7

WIRE BASKET OR BAG

1. our rollator is supplied with a bag; raise the padded seat, align the bag with the

frame (Fig. 8) and close each of the fabric popper ties around the frame to hold the

bag in place (Fig. 9) and then lower the seat.

Fig. 8 Fig. 9

Usage and Maintenance Instructions Ver.3 09/2013 (2634)

OPERATING THE BRAKES

The handbrake on your Aidapt Rollator works very similar to a bicycle hand brake:

1. To stop, gently apply a gripping pressure to both brakes simultaneously (Fig. 10),

this will slow down and stop your rollator.

2. The brakes on your Aidapt Rollator have a park option (Fig. 11). To operate the park

option, push downwards on both brakes simultaneously. ou will feel the brake

make a very slight click. our brakes are now in the ‘lock’ position.

3. To unlock, simply pull up the brake again, you will hear a slight click as the ‘park’

disengages.

Fig. 10 Fig. 11

STORAGE

1. Grip the side bar and lift (Fig. 12).

2. Continue lifting until the rollator fully closes (Fig. 13).

3. ou may also wish to remove the half-round back for storage; to do so pull the

silver coloured locking buttons located on either side of the tube lock outwards

(Fig. 14), then lift up the back to detach (Fig. 15).

Fig. 12 Fig. 13 Fig. 14 Fig. 15

Usage and Maintenance Instructions Ver.3 09/2013 (2634)

ADJUSTMENT

1. our Aidapt Rollator brake system will require periodic adjustment. The brake

adjustment is similar to bicycle brakes.

2. Fig. 17 shows the brake handle in its

default delivered position. Should the

brakes need adjusting they can be

tightened by unlocking nut A and then

unscrewing (anti-clockwise) Nut B.

When the brake arm (see Fig. 16) has a

3 mm clearance then Nut A should be

retightened. An example of a user

adjusted brake handle is show in Fig. 18.

3. When adjusted the brakes should work

in both normal braking and in parking

mode. If needed then Nut B in Fig. 17/18

can be turned further anti-clockwise,

which will tighten the brake cable more.

Fig. 6

4. If the brake handles are fully adjusted and more tightening is required refer to

Fig. 16 and carefully release the locking screws using an allen key. Adjust the cable

to both brakes until the brake arms evenly clear the wheels by approx. 3 mm.

5. Retighten the locking screw.

6. Check the park brakes by pushing down on the brake handles, ensuring that both

brakes lock in the park position.

7. Lift the two ‘braked’ wheels off the ground and spin to ensure they turn freely. If

either of the braked wheels rubs onto the brake arm, please check for obstructions

and repeat the brake adjustment procedure above.

8. It is important that you check brake adjustments on a regular basis to take into

account wear and tear. However brake adjustment must be checked at least once a

month and definitely prior to a change of user.

Fig. 7 Fig. 8

NB. Wheel design may vary.

Brake arm

Usage and Maintenance Instructions Ver.3 09/2013 (2634)

REISSUE

If you reissue or are about to reissue this product, please thoroughly check all components

for their safety.

This includes:

•Bent or damaged tubes or cracks at the tube joints.

•Loose or worn horseshoe clips

•Elongated adjustment holes.

•Loose handles.

•Loose or worn wheels and wheel fasteners (where fitted)

•Smooth, worn or split ferrules (rubber tips).

•Brake adjustment.

Replace all worn, missing or damaged parts where necessary. If in any doubt, please do

not issue or use, but immediately contact your supplier for service support.

CARE AND MAINTENANCE & YOUR OBLIGATION

1. Only use your Aidapt Rollator for the purpose for which it intended, which is as an

aid to walking. It is intended your rollator is only used on standard pavements or at

home. It should not be used on rough terrain or pot-holed surfaces. The use of your

rollator on these surfaces can seriously compromise your safety and may damage

your rollator beyond repair.

2. Keep your Aidapt Rollator clean by wiping down with a damp cloth with a mild

detergent. Do not under any circumstances use an abrasive or solvent based

cleaner, as this will seriously damage the rollator and void your warranty.

3. Wipe off all surfaces with a dry cloth and use a water dispersing agent such as

WD40 on all metal joints.

4. Check that all wheels and the folding mechanism function correctly and that all

wheels move freely. Pay particular attention to the front wheels, ensuring that they

rotate freely and without obstruction.

Withdraw your Aidapt Rollator immediately if any of the wheels become

difficult to turn or if you suspect damage or any other fault.

5. Monthly Checks - check that the side locking levers are properly secure (Fig. 2).

Check that no components are loose. Check the adjustment to your brakes

(Fig. 16); Ensure that the brakes are correctly adjusted with 3 mm between both

tyres and brake(s), check castors.

6. Do not fit any parts or accessories to your Aidapt Rollator manufactured by another

company. To do so will annul your warranty and may seriously compromise your

safety.

7. We suggest that you check your Aidapt Rollator visually every day. However we

recommend that you should have your rollator serviced every three months or less

if used by, or issued to, various users. Servicing should be carried out at an

approved service station or directly by Aidapt.

Usage and Maintenance Instructions Ver.3 09/2013 (2634)

CLEANING

Clean your Rollator using a non-abrasive cleaner or mild detergent with a soft cloth. Abrasive

cleaners e.g. AJAX and/ or abrasive cleaning pads may seriously damage the product beyond

repair and should not be used. Always ensure that you wipe dry the equipment after

cleaning.

MAINTENANCE

Please make a safety check of the product at regular intervals or if you have any concerns.

WARRANTY

This product carries a 12 month warranty from the date of purchase against manufacturing

defects.

Misuse or Damage is not covered.

This warranty does not affect your statutory rights.

IMPORTANT INFORMATION

The information given in this instruction booklet must not be taken as forming part of or

establishing any contractual or other commitment by Aidapt Bathrooms Limited, Aidapt

(Wales) Ltd or its agents or its subsidiaries and no warranty or representation concerning the

information is given.

Please exercise common sense and do not take any unnecessary risks when using this

product; as the user you must accept liability for safety when using the product.

Please do not hesitate to contact the person who issued this product to you or the

manufacturer (detailed below) if you have any queries concerning the assembly/use of your

product.

Aidapt Bathrooms Ltd, Lancots Lane, Sutton Oak, St Helens, WA9 3EX

Telephone: +44 (0) 744 745 020 • Fax: +44 (0) 744 745 00 • Web: www.aidapt.co.uk

Email: [email protected] • [email protected] • [email protected]

Déambulateur 4 roues en aluminium

Notice d’utilisation et d’entretien

Notice d'utilisation et d'entretien Ver.3 01/2014 (2634)

INTRODUCTION

Nous vous remercions d’avoir acheté chez Aidapt le déambulateur 4 roues en aluminium .

Notre déambulateur 4 roues, comme tous nos produits, est fabriqué à partir de matériaux de la meilleure

qualité.

N.B. Cet équipement doit être installé par une personne compétente.

V 176/V 176A/V 176AB Déambulateur rouge en aluminium Limite de poids de 132 kg (21 st.)

V 177A/V 177A/V 177AB Déambulateur bleu en aluminium Limite de poids de 132 kg (21 st.)

V 178A/V 178A/V 178AB Déambulateur argent en aluminium Limite de poids de 132 kg (21 st.)

Veuillez ne pas excéder la limite de poids indiquée un manquement à cette recommandation

pourrait mettre à risque son utilisateur.

AVANT UTILISATION

•Retirez parfaitement l'emballage. Évitez d'utiliser un couteau ou tout instrument coupant qui

pourrait endommager la surface du produit.

•Vérifiez votre produit pour tout dommage visible. En cas de dommage ou de défaut suspect,

veuillez ne pas utiliser votre produit et contactez votre fournisseur.

USAGE PRÉVU

Votre déambulateur Aidapt a été conçu pour vous assister lors de la marche et pour porter des articles

légers en utilisant le panier fourni. Le panier a été spécialement conçu pour s'adapter à votre

déambulateur, veuillez seulement utiliser le panier fourni pour votre déambulateur Aidapt. Ne pas

utiliser ou combiner des sacs/paniers d'autres fabricants.

Lorsque vous ne l'utilisez pas, vous pouvez simplement plier le déambulateur Aidapt et l'entreposer

jusqu'à ce que vous en ayez besoin de nouveau. La gamme d'Aidapt de tri-walkers et déambulateurs est

conçue pour être utilisée à l'intérieur mais aussi à l'extérieur.

CARACTÉRISTIQUES

•Freins débrayables faciles avec verrouillage

•Ajustement du câble de frein simplifié

•Roues solides en plastique souple

•Roues avant orientables

•Mécanisme de pliage avec verrouillage

•Hauteur ajustable

•Verrouillage ergonomique facilité sur le côté

roues pour un ajustement de la hauteur

•oignées ergonomiques pour réduire la pression

Fig. 1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Ayuda a la movilidad de aidapt

Manuales populares de Ayuda a la movilidad de otras marcas

Alber

Alber Scalamobil iQ Manual de usuario

Ferno

Ferno CCT-PX Manual de usuario

HEPRO

HEPRO Gripo Manual de usuario

Otto Bock

Otto Bock Pheon 3R62 Manual de usuario

NRS Healthcare

NRS Healthcare M11090 Manual de usuario

Medline

Medline MDS86835DSHEC Guía de instalación

Guldmann

Guldmann Twin Turner II Manual de usuario

Drive

Drive ROOMBA Manual de usuario

Gate

Gate Balder Manual de usuario

Decon wheel

Decon wheel TNS Notos Manual de usuario

ExoAtlet

ExoAtlet ExoAtlet-II Manual de usuario

Invacare

Invacare Storm Series Manual de instrucciones

Rhythm Healthcare

Rhythm Healthcare B3800F Manual de usuario

AMF-BRUNS

AMF-BRUNS PROTEKTOR Manual de usuario

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Manual de usuario

Rhythm Healthcare

Rhythm Healthcare C500U Manual de usuario

Lumex

Lumex RJ4200A Manual de usuario

Rebotec

Rebotec Jumbo Manual de usuario

aidapt VP176 Manual de programación

Manuales populares de Ayuda a la movilidad de otras marcas