Agri-Fab 45-01772 Manual de usuario
• Safety
• Assembly
• Operation
• Maintenance
• Parts
PRINTED IN U.S.A. FORM NO. 7592 (REV. 7/03)
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
OWNERS MANUAL
MODEL NO.
45-01772
14 CU. FT. FARM/YARD CART
Agri-Fab¨
the fastest way to purchase parts
www.speedepart.com
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
2
RULES FOR SAFE OPERATION
FIGURE 1
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
(1) Screw Driver
(1) Pliers
(1) 7/16" Wrench
When assembling your cart, place the heads of all
screws to the inside and hex nuts with flat washers
to the outside.
The bottom panel has one galvanized
edge; this is the rear. The front edge
has three holes. See figure 2.
NOTE
2. Line up three holes in bottom panel with holes in
front angle assembly. Start three 1/ " x 1" screws
through bottom panel, then through angle. Secure
screws with flat washers and hex nuts. Tighten
securely. See figure 2.
1. Lay the front angle assembly down (flat) on floor
and stand the bottom panel in position as shown in
figure 2.
Preventing accidents is the responsibility of every
equipment operator. The following general safety
precautions must be fully understood and followed by
every operator.
1. Do not at any time carry passengers in this cart. It
is designed for carrying materials only and not
intended to carry passengers.
2. Be careful on any grade (hill) and stay off of steep
grades.
3. Use caution when loading cart to avoid tipping.
. Avoid large holes and ditches when transporting
loads.
REF. QTY. DESCRIPTION
Your Farm/Yard Cart carton contains a hardware
package with parts as shown in the chart below
and in figure 1.
Contents of Hardware Pack: (See figure 1)
A 6 Screws, 1/ -20 x 2" Long
B 2 Screws, 1/ -20 x 1-1/2" Long
C Screws, 1/ -20 x 1-1/ " Long
D 25 Screws, 1/ -20 x 1" Long
E Cotter Pins
F 37 Hex Nuts, 1/ -20 Thread
G Flat Washers, 1-1/2" O.D.
H 33 Flat Washer, 1/ " I.D.
I Lock Washers, 1/ "
J 2 Tube Cap, 1" x 1" Long
HARDWARE REFERENCE CHART
FIGURE 2
1/4" x 1"
1/4" x 2"
1/4" x 1-1/4"
ABCD
F
H
G
E
1/4" x 1-1/2'
J
I
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
3
3. Turn the front angle assembly and bottom panel
upside down as shown in figure 3.
. Lay each side angle on the bottom panel so that
the two holes (for the axle clamp) are closer to the
front angle assembly. See figure 3.
5. Secure both axle clamps to the side angles and
the bottom panel using four 1/ " x 1-1/ " screws,
lock washers and hex nuts. Make only finger
tight until the axle is assembled. See figure 3.
FIGURE 5
FIGURE 3
7. Stand the cart on end with the front angle assem-
bly down on the floor. Temporarily place the four
large 1-1/2" dia. flat washers (axle washers) on
the inside of front angle assembly. See figure 5.
These washers act as shims and are
just for assembly purposes. You will
remove them later to use on the axle.
NOTE
8. Lay the front panel down onto the front angle
assembly, on top of the four large 1-1/2" dia.
washers. See figure 6.
FIGURE 4
6. Assemble four 1/ " x 1" screws, flat washers and
hex nuts to the side angles and bottom panel
using the holes on each side of the axle clamps.
Tighten the four nuts. See figure .
FIGURE 6
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
FIGURE 8
FIGURE 7
9. Position a side panel against a side angle, resting
it down on top of the front panel. Place a support
strap on the outside of the side angle and start a
1/ " x 1" screw through the second hole in the
side panel, the side angle and the support strap.
Secure with a flat washer and hex nut. Make only
finger tight at this time. See figure 7.
10. Start a 1/ " x 1" screw through the top hole in the
side panel, the front angle assembly and the sup-
port strap. Secure with a flat washer and hex nut.
Make only finger tight at this time. See figure 7.
11. Repeat steps 9 and 10 for the other side panel.
FIGURE 9
15. Lay the cart down on the floor so that the sides are
in the normal upright position. Remove the front
panel by sliding it up, then remove the four large
washers you used for shims. See figure 9.
12. Start one 1/ " x 1" screw through the bottom hole
in the side panel and the front angle assembly.
Start another 1/ " x 1" screw through the front hole
in the side panel and the side angle. Secure with
two flat washers and two hex nuts, making only
finger tight at this time. See figure 8.
13. Repeat step 12 for the other side panel.
1 . Tighten all nuts and screws securely at this time,
except for nuts and screws in axle clamps. See
figure 8.
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
5
16. Turn the cart upside down. Place the handle tube
on the bottom of the cart as shown in figure 10.
Place the four tube clamps over the handle tube,
with the longer leg of each tube clamp to the
outside. Secure the four tube clamps over the
handle tube using eight 1/ " x 1" screws, eight flat
washers and eight hex nuts. Make only finger tight
until all eight screws are in place and then tighten
securely. See figure 10.
The length of the handle tube can be
adjusted by sliding the tube in or out
before tightening the four clamps. See
figure 10.
NOTE
FIGURE 10
17. Insert a 1/ " x 1" screw through the hole at the rear
of each side panel and the hole at the rear of each
side angle. Secure with 1/ " flat washers and 1/ "
hex nuts, making only finger tight at this time.
See figure 11.
18. Place the tube caps on the ends of the "W" shaped
leg tube. See figure 11.
19. With the cart still upside down, assemble the leg
tube to the bottom of the cart. Line up the two
holes in the center of the leg tube with the holes in
the bottom of the cart. Secure the leg tube to the
bottom of the cart with two 1/ " x 2" screws, 1/ "
flat washers and 1/ " hex nuts. Make only finger
tight at this time. See figure 11.
20. Attach the leg tube to the side panels with four 1/ "
x 2" screws, 1/ " flat washers and 1/ " hex nuts.
Make only finger tight at this time. See figure
11.
21. Fasten the support straps to the leg tube with two
1/ " x 1-1/2" screws, 1/ " flat washers and 1/ "
hex nuts. See figure 11.
22. At this time tighten securely all screws and nuts
assembled in figure 11.
FIGURE 11
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
6
FIGURE 12
26. Turn cart right side up, so that it rests on its
wheels.
27. Place front panel in guides to complete assembly.
28. Your cart is now ready to use.
MAINTENANCE
1. Grease or oil wheel bearings occasionally. Use
automotive wheel bearing type grease or 20 weight
oil.
2. Periodically retighten all screws, especially after
heavy use. Do not exceed load capacity rating
of 400 lbs.
3. Clean cart thoroughly after each use.
. Store indoors during severe weather.
5. Apply light coat of varnish to all wood surfaces
annually.
6. Use glossy black enamel spray paint to touch up
scratched or worn painted metal surfaces.
23.Slide the axle through the axle clamps. See figure
12.
2 . Assemble a cotter pin to the inner hole at one end
of the axle. Place a 1-1/2" flat washer, a wheel and
then another 1-1/2" flat washer onto the axle.
Secure the wheel with a cotter pin assembled to
the outer hole at the end of the axle. Repeat step
for other wheel. See figure 12.
25. Center the wheels and axle side to side. Tighten
the four nuts on the axle clamps.
RECOMMENDED TIRE PRESSURE 30-35 PSI
MAXIMUM TIRE PRESSURE 35 PSI
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
7
MODEL 45-01772 14 CU. FT. FARM/YARD CART
1 7590 1 Bottom Panel
2 2 889 1 Axle, Wheel
3 7589 2 Side Panel
021 2 Tube Caps
5 7588 1 Front Panel
6 2 887 1 Side Angle, L.H.
7 2 888 1 Side Angle, R.H.
9 031 1 Handle Tube
10 522 1 Leg Tube
11 033 Clamp, Tube
12 23882 2 Support Strap
13 62535 1 Front Angle Assembly
1 39 5 2 Wheel w/Bearings 26"
19 016 Ball Bearings 3/ " I.D.
20 39 9 Flat Washer, 25/32" x 1-1/2" x 3/32"
21 3010 Cotter Pin, 1/8" x 1-1/ " *
22 758 6 Truss Head Screw, 1/ -20 x 2" Lg.*
25 259 25 Truss Head Screw, 1/ -20 x 1" Lg.*
26 3088 33 Flat Washer, 1/ " *
27 3178 37 Hex Nut, 1/ -20 Thread *
28 020 Truss Head Screw, 1/ -20 x 1-1/ " Lg.*
29 017 2 Truss Head Screw 1/ -20 x 1-1/2" Lg.*
30 23917 2 Axle Clamp
31 3177 Lock Washer, 1/ "
7592 1 Owner's Manual
REF. PART QTY. DESCRIPTION
NO. NO.
REF. PART QTY. DESCRIPTION
NO. NO.
*Purchase Common Hardware Locally.
the fastest way to purchase parts
www.speedepart.com
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab, Inc.
303 West Raymond
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
© 1999 Agri-Fab, Inc.
For Agri Fab Discount Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
Tabla de contenidos
Otros manuales de Carrito para exteriores de Agri-Fab
Agri-Fab
Agri-Fab Poly Lawn Cart 45-02265 Manual de usuario
Agri-Fab
Agri-Fab 45-01763 Manual de usuario
Agri-Fab
Agri-Fab 45-0270 Manual de usuario
Agri-Fab
Agri-Fab 501885A Manual de usuario
Agri-Fab
Agri-Fab 45-0345 Manual de usuario
Agri-Fab
Agri-Fab Explorer 45-0175 Manual de usuario
Agri-Fab
Agri-Fab Repair Parts For Utility Carts 190-425A Manual de uso y cuidado
Agri-Fab
Agri-Fab 190-521-000 Manual de usuario
Agri-Fab
Agri-Fab Poly Lawn Cart 45-02264 Manual de usuario
Agri-Fab
Agri-Fab 45-03503 Manual de usuario
Agri-Fab
Agri-Fab 45-02402 ATV Manual de usuario
Agri-Fab
Agri-Fab SUPER 17 Manual de usuario
Agri-Fab
Agri-Fab Lawn Care Made Easy 45-0554 Manual de usuario
Agri-Fab
Agri-Fab 45-02261 Manual de usuario
Agri-Fab
Agri-Fab 45-01013-999 Manual de usuario
Agri-Fab
Agri-Fab 45-01754 Manual de usuario
Agri-Fab
Agri-Fab 14 cu. ft. Farm/Yard Cart 45-01773 Manual de usuario
Agri-Fab
Agri-Fab 45-03453 Manual de usuario
Agri-Fab
Agri-Fab Utility Cart 45-01001 Manual de usuario
Agri-Fab
Agri-Fab 45-01763 Manual de usuario
