Agilent Technologies E6630A Manual de usuario

Data Sheet

The Agilent Technologies E6630A wireless connectivity test set integrates up to two vector signal

analyzers, and two vector signal generators in a single PXI frame, creating a one-box tester that

accelerates your wireless connectivity devices time to market with fast and accurate RF test for

802.11a/b/g/n/ac WLAN, Bluetooth®1.0 to 4.0, and GNSS.

Speciﬁcation

Specifications describe the performance parameters covered by the product warranty and are

valid only at room temperature (approximately 25 °C) unless otherwise noted. Warranted speci-

fications indicate the breadth of the population (≈2 σ) of performance tolerances expected to be

met in 95 percent of the cases with a 95 percent confidence. Data represented in this document

are specifications unless otherwise noted.

Typical

Typical describes additional product performance information that is not covered by the product

warranty. It is performance beyond specifications that 95 percent of the units exhibit with a 95

percent confidence level. This data, shown in italics, does not include measurement uncertainty

and is valid only at room temperature (approximately 25 °C).

Nominal

Nominal values indicate expected performance, or describe product performance that is useful

in the application of the product, such as a 50-Ω connector. This data is not warranted and is

measured at room temperature (approximately 25 °C).

The test set will meet its specification when:

• The test set is within its calibration cycle

• The test set has been turned on for at least 30 minutes

Recommended best practices in use

At environment temperatures above 45 °C, chassis fan should be set to high.

Deﬁnitions and Conditions

Vector Signal Analyzer Performance

Performance

Maximum capture memory 1 GSa (4 GB)

Frequency and time specifications

Frequency range 2.4 to 2.5 GHz

4.85 to 6 GHz

Frequency reference (100 MHz)

Accuracy ± [(time since last adjustment x aging rate) ± temperature effects ± calibration accuracy]

Aging rate Daily < ±0.5 ppb/day, after 72 hours of warm-up

Yearly < ±0.10 ppm/year, after 72 hours of warm-up

Total 10 years < ±0.6 ppm/10 years, after 72 hours of warm-up

Achievable initial calibration accuracy

(at time of shipment, after warm-up)

±0.05 ppm

Temperature effects < ±10 ppb, 20 to 30 °C

< ±50 ppb, 5 to 50 °C

Residual FM ≤ 0.25 Hz p-p in 20 ms nominal

CW measurement frequency accuracy

Accuracy (transmitter frequency x frequency reference accuracy) ±50 Hz

Resolution 1 Hz

Arbitrary frequency switching speed 400 µs nominal

Analysis bandwidth

Maximum bandwidth 80 MHz

Triggering

Trigger Free run, external 1, external 2, video, line, periodic

Trigger delay range –150 to 500 ms

Resolution 0.1 µs

Amplitude accuracy and range specifications

Input level ranges (average power)

RF IN –70 to +30 dBm

Total absolute amplitude accuracy

RF IN 2.4 to 2.5 GHz: < ±0.42 dB typical

Input signal –50 to +23 dBm 4.85 to 6 GHz: < ±0.42 dB typical

Input voltage standing wave ratio (VSWR)

RF IN 2.4 to 2.5 GHz: < 1.3:1 nominal

4.85 to 6 GHz: < 1.7:1 nominal

Amplitude switching speed ≤ 1.5 ms nominal

Spurious responses

f ≥ 10 MHz from carrier 2.4 to 2.5 GHz, 4.85 to 6 GHz: < –55 dBc typical

Phase noise

5.8 GHz, 10 kHz offset < –105 dBc/Hz nominal

Analyzer

Vector Signal Generator Performance

Performance

Arb sample rate range and bandwidth Clock rate: 100 to 200 MSa/s

Arb sample memory (storage capacity) 4 GB memory; 1024 MSa of IQ data

Frequency specifications

Frequency range All speciﬁcations apply over the range

1.1 to 1.7 GHz

2.4 to 2.5 GHz

4.85 to 6 GHz

Frequency accuracy Refer to VSA frequency reference accuracy

Frequency resolution 0.01 Hz

Arbitrary frequency settling < 240 µs typical

Amplitude specifications

Output level ranges1

RF OUT –110 to +10 dBm typical

Absolute level accuracy

RF OUT 1.1 to 1.7 GHz, –110 to +10 dBm: < ±0.5 dB typical

2.4 to 2.5 GHz, –110 to +10 dBm: < ±0.5 dB typical

4.85 to 6 GHz, –110 to +10 dBm: < ±0.5 dB typical

Setting resolution 0.01 dB

Level settling time < 1.5 ms to within 0.2 dB nominal

Output voltage standing wave ratio (VSWR)

RF OUT 1.1 to 1.7 GHz: < 1.25:1 nominal

2.4 to 2.5 GHz: < 1.4:1 nominal

4.85 to 6.0 GHz: < 1.6:1 nominal

Spectral purity

Harmonics and spurious

VSG RF OUT; harmonics at –10 dBm

output power

< –30 dBc nominal

RF OUT; non-harmonic spurious

(CW mode; > 220 kHz offset)

< –62 dBc nominal

Phase noise

RF OUT; 20 kHz offset 1.1 to 1.7 GHz: –122 dBc/Hz nominal

2.4 to 2.5 GHz: –116 dBc/Hz nominal

4.85 to 6 GHz: –108 dBc/Hz nominal

Generator

1. Power level is user-settable beyond the speciﬁed range (from –150 to +18 dBm)

General Speciﬁcations

Power requirements

Voltage 100/120 V, 1000 W

220/240 V, 1200 W

Input frequency range 50/60 Hz

Power consumption E6630A-001, 1-port: 330 W maximum

E6630A-002, 2-port: 520 W maximum

Data storage

Internal 160 GB (SSD)

External Supports four USB 2.0 (Type A) compatible memory devices

Size and weight

Dimensions (W x H x D) With feet: 450 mm x 197 mm x 545 mm (18 in x 8 in x 21.5 in)

Without feet: 450 mm x 188 mm x 545 mm (18 in x 7.5 in x 21.5 in)

Weight 1-port: 21.12 kg (47 lbs) (with power cord)

2-port: 24.01 kg (53 lbs) (with power cord)

Environmental characteristics

Operating temperature +5 to +50 °C

Storage temperature –40 to +65 °C

EMC Complies with European EMC Directive

2004/108/EC

• IEC/EN 61326-2-1

• CISPR Pub 11 Group 1, Class A

• AS/NZS CISPR 11

• ICES/NMB-001

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme a la norme NMB-001 du Canada

Environmental stress Samples of this product have been type tested in accordance with the Agilent

Environmental Test Manual and veriﬁed to be robust against the environmental stresses

of storage, transportation, and end-use; those stresses include, but are not limited to,

temperature, humidity, shock, vibration, altitude, and power line conditions; test methods

are aligned with IEC 60068-2 and levels are similar to MILPRF-28800F Class 3

Safety

Complies with European Low Voltage Directive 73/23/EEC, amended by 93/68/EEC

• IEC/EN 61010-1

• Canada: CSA C22.2 No. 61010-1-04

• USA: UL Std. 61010-1

General Speciﬁcations (continued)

Acoustic emissions

Auto fan (25 °C ambient) High fan

Sound pressure level1,2 53 dBA 69 dBA

Remote programming

Ethernet Two 10/100/1000Base-T (RJ45)

Calibration cycle

The recommended calibration cycle is two years. Calibration services are available through

Agilent service centers

Warranty

This test set is supplied with a standard three year warranty. Optional 5-year warranty

available

Maximum applied CW power

RF IN +30 dBm (1 W)

RF OUT +30 dBm (1 W)

Max DC voltage 25 Vdc

Front Panel

LAN TCP/IP interface

Standard 10/100/1000Base-T

Connector RJ45 Ethertwist

RF IN

Connector Type-N female, 50 Ω nominal

RF OUT

Connector Type-N female, 50 Ω nominal

REF IN

Connector BNC female, 50 Ω nominal

Input amplitude range –0.5 to +10 dBm nominal

Frequency lock range ±5 x 10–6 of speciﬁed external reference input frequency

TRIG IN

Connector BNC female

Impedance 10 kΩ nominal

Trigger level range –5 to +5 V

1. At operator position.

2. Referenced to 1 pW.

TRIG 1/2/3 (configurable)

Connector BNC female

Trigger input level range –5 to +5 V, impedance > 10 kΩ nominal

10 MHz Ref IN

Connector BNC female, 50 Ω nominal

Trigger input level range –5 to +5 V, impedance > 10 kΩ nominal

Trigger output level range 3.3 V LVTTL, impedance 50 Ω nominal

USB 2.0 ports

Master (4 ports)

Standard Compatible with USB 2.0

Connector USB Type-A female

Output current 0.5 A nominal

GPIB interface

Connector Micro-D 25-pin, IEEE-488 bus connector

GPIB code SH1, AH1, T6, SR1, RL1, PP0, DC1, C1, C2, C3, C28, DT1, L4, C0

Video

Connector DVI-I (VGA with DVI/VGA adapter)

Resolution Up to 1920 x 1200, 60 Hz

Up to 2048 x 1536, 75 Hz

10 MHz Ref OUT

Connector BNC female, 50 Ω nominal

Output amplitude > 0 dBm nominal

Frequency 10 MHz ± (10 MHz x frequency reference accuracy)

Input amplitude range –0.5 to +10 dBm nominal

Frequency lock range ±5 x 10–6 of speciﬁed external reference input frequency

Front Panel (continued)

V9077A WLAN Measurement Application Key Speciﬁcations1

Supported WLAN standards

Standard version 802.11a, 802.11a turbo mode

802.11b/g DSSS/CCK/PBCC

802.11g ERP-OFDM, 802.11g DSSS-OFDM

802.11n (20 MHz, 40 MHz) HT Mixed, HT Greenﬁeld, Non-HT, MCS = 0-7

802.11ac (20/40/80 MHz) MCS = 0-9

Modulation formats BPSK, QPSK, 16QAM, 64QAM, 256QAM

Technology IEEE 802.11b/g

(DSSS/CCK/PBCC)

IEEE 802.11a/g

(ERP-OFDM,

DSSS-OFDM)

IEEE 802.11n

(20 and 40 MHz)

IEEE 802.11ac

(20/40/80 MHz)

Modulation analysis

RMS EVM ● ● ● ●

Peak EVM ● ● ● ●

Pilot EVM ● ● ●

Data EVM ● ● ●

1K chips EVM ●

RMS magnitude error ●

Peak magnitude error ●

RMS phase error ●

Peak phase error ●

Frequency error ● ● ● ●

Chip clock error ●

Symbol clock error ● ● ●

I/Q origin offset (CFL) ● ● ● ●

Quadrature skew ● ● ● ●

I/Q gain imbalance ● ● ● ●

Carrier suppression ●

Average burst power ● ● ● ●

Peak burst power ● ● ● ●

Peak-to-average power ratio ● ● ● ●

Modulation format ● ● ● ●

Preamble frequency error ● ●

OFDM data burst info ● ●

OFDM HT-sig info ● ●

Channel power ● ● ● ●

Occupied bandwidth ● ● ● ●

Spectrum emission mask (SEM) ● ● ● ●

Spurious emissions ● ● ● ●

Power vs. time ● ● ● ●

Spectral ﬂatness ● ● ● ●

I/Q waveform ● ● ● ●

1. Speciﬁcations apply to frequencies between 2.4 to 2.5 GHz and 4.85 to 6 GHz.

V9077A WLAN Measurement Application Key Speciﬁcations1(continued)

WLAN analyzer error vector magnitude (EVM)

Residual EVM

Phase tracking on, pre-amble only

802.11b: 2.4 to 2.5 GHz, 20 MHz ≤ 4% nominal, –20 to 0 dBm

802.11g: 2.4 to 2.5 GHz, 20 MHz ≤ –51 dB typical, –20 to 0 dBm

802.11a: 4.85 to 6 GHz, 20 MHz ≤ –46 dB typical, –20 to 0 dBm

802.11n: 4.85 to 6 GHz, 20 MHz ≤ –47 dB typical, –20 to 0 dBm

802.11n: 4.85 to 6 GHz, 40 MHz ≤ –46 dB typical, –20 to 0 dBm

802.11ac: 4.85 to 6 GHz, 80 MHz ≤ –43 dB typical, –20 to 0 dBm

WLAN source error vector magnitude (EVM)

802.11b: 2.4 to 2.5 GHz, 20 MHz ≤ 4% nominal, –7 dBm

802.11g: 2.4 to 2.5 GHz, 20 MHz ≤ –50 dB typical, –7 dBm

802.11a: 4.85 to 6 GHz, 20 MHz ≤ –44 dB typical, –7 dBm

802.11n: 4.85 to 6 GHz, 20 MHz ≤ –43 dB typical, –7 dBm

802.11n: 4.85 to 6 GHz, 40 MHz ≤ –44 dB typical, –7 dBm

802.11ac: 4.85 to 6 GHz, 80 MHz ≤ –42 dB typical, –7 dBm

WLAN spectral emission mask(SEM)

WLAN format 802.11 ± Ranges [MHz] Relative power [dBc(avg)]

–20 dBm average in 0 dBm average in

802.11n, 40 MHz 40 to 60 ≤ –53 dBc (nominal) ≤ –57 dBc (nominal)

802.11ac, 80 MHz 80 to 120 ≤ –49 dBc (nominal) ≤ –50 dBc (nominal)

1. Speciﬁcations apply to frequencies between 2.4 to 2.5 GHz and 4.85 to 6 GHz.

V9081A Bluetooth®Measurement Application Key Speciﬁcations1

Supported Bluetooth standards

Standard version Bluetooth Basic Rate Bluetooth EDR Bluetooth Low Energy

Modulation formats GFSK Header: GFSK

Data: π/4-DQPSK,

8DPSK

GFSK

Supported Bluetooth measurements Bluetooth Basic Rate Bluetooth EDR Bluetooth Low Energy

Transmit analysis

Output power (in time domain)

Peak power ● ●

Average power ● ●

Modulation characteristics

ΔF1 avg (11110000) ● ●

ΔF2 avg (10101010) ● ●

Min ΔF1/ΔF2 max ● ●

Max ΔF1/ΔF2 max ● ●

ΔF2 > 115 kHz ● ●

Initial carrier frequency tolerance (ICFT) ● ●

Carrier frequency drift

Frequency drift ● ●

Max drift rate ● ●

Adjacent channel power ●

Output power –20 dB bandwidth ●

EDR transmit analysis

Relative transmit power

GFSK average power ●

DPSK average power ●

Relative power ●

Frequency stability and modulation accuracy

Freq offset ωi/ω0, ωi + ω0 ●

RMS DEVM (differential DVM) ●

Peak DEVM ●

Differential phase decoding

BER ●

Bit error ●

99% DEVM ●

EDR in-band spurious emissions ●

LE in-band emissions ●

1. Speciﬁcations apply for frequencies between 2.4 to 2.5 GHz.

Otros manuales para E6630A

Tabla de contenidos

Otros manuales de Equipo de prueba de Agilent Technologies

Agilent Technologies

Agilent Technologies U2701A Manual de usuario

Agilent Technologies

Agilent Technologies N5980A Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies 90000 X Series Manual de usuario

Agilent Technologies

Agilent Technologies E4406A VSA Series Manual

Agilent Technologies

Agilent Technologies 54810A Manual de usuario

Agilent Technologies

Agilent Technologies N9360A Manual de usuario

Agilent Technologies

Agilent Technologies 87050A Option K24 Manual

Agilent Technologies

Agilent Technologies 85056A Manual

Agilent Technologies

Agilent Technologies 16334A Manual de operación

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Manual de usuario

Agilent Technologies

Agilent Technologies Medalist i3070 Series 5i Manual de usuario

Agilent Technologies

Agilent Technologies U3042AE08 Manual de usuario

Agilent Technologies

Agilent Technologies auroraSonata Manual de usuario

Agilent Technologies

Agilent Technologies 83480A Manual de usuario

Agilent Technologies

Agilent Technologies 8960 Series 10 Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Manual

Agilent Technologies

Agilent Technologies Auroraduet N1726A Manual de usuario

Agilent Technologies

Agilent Technologies Ininiium 9000 Manual de usuario

Agilent Technologies

Agilent Technologies 4072A Advanced Manual de usuario

Agilent Technologies

Agilent Technologies E6621A Manual de usuario

Agilent Technologies

Agilent Technologies E8285A Manual de usuario

Agilent Technologies

Agilent Technologies J-BERT N4903B Manual de usuario

Agilent Technologies

Agilent Technologies 16034E Manual de operación

Agilent Technologies

Agilent Technologies 5530 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario

Ritmix

Ritmix RAT-701 Manual de usuario