Agilent Technologies 86100A Cómo utilizar

Agilent Technologies

Agilent 86100A/B/C/D

Infiniium DCA Series &

N1010A FlexDCA

Firmware Release Notes

(A.12.02 DCA and below &

A.02.50 FlexDCA and below)

Company 2010 - 2013

adaptation, or translation without

prior written permission is prohibited,

except as allowed under copyright

laws.

October 2013

14th Edition

Made in USA.

Agilent Technologies Company

Oscilloscope Products Division

1400 Fountaingrove Parkway

Santa Rosa, CA 95403, USA

Notice.

The information contained in this

document is subject to change with-

out notice. Companies, names, and

data used in examples herein are ficti-

tious unless otherwise noted. Agilent

Technologies makes no warranty of

any kind with regard to this material,

including but not limited to, the

implied warranties of merchantabil-

ity and fitness for a particular pur-

pose. Agilent Technologies shall not

be liable for errors contained herein

or for incidental or consequential

damages in connection with the fur-

nishing, performance, or use of this

material.

Restricted Rights Legend.

Use, duplication, or disclosure by the

U.S. Government is subject to restric-

tions as set forth in subparagraph (c)

(1) (ii) of the Rights in Technical Data

and Computer Software clause at

DFARS 252.227-7013 for DOD

agencies, and subparagraphs (c) (1)

and (c) (2) of the Commercial Com-

puter Software Restricted Rights

clause at FAR 52.227-19 for other

agencies.

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

Contents

N1010A FlexDCA Firmware Release Notes 5

A.02.50 Release Notes, October, 2013 (Differences from Release A.02.02) 5

A.02.02 Release Notes, May, 2013 (Differences from Release A.02.00) 7

A.02.00 Release Notes, January, 2013 (Differences from Release A.01.80) 7

A.01.80 Release Notes, June, 2012 (Differences from Release A.01.70) 9

A.01.70 Release Notes, April, 2012 (Differences from Release A.01.61) 11

A.01.61 Release Notes, February, 2012 (Differences from Release A.01.60) 13

A.01.60 Release Notes, December, 2011 (Differences from Release A.01.50) 15

A.01.50 Release Notes, September, 2011 (Differences from Release A.01.03) 16

A.01.03 Release Notes, April, 2011 (Differences from Release A.01.02) 17

86100D Firmware Release Notes 19

A.12.02 Release Notes, May, 2013 (Differences from Release A.12.00) 19

A.12.00 Release Notes, January, 2013 (Differences from Release A.10.80) 19

86100D/C Firmware Release Notes 20

A.10.80 Release Notes, June, 2012 (Differences from Release A.10.70) 20

A.10.70 Release Notes, April, 2012 (Differences from Release A.10.60) 20

A.10.60 Release Notes, December, 2011 (Differences from Release A.10.50) 20

A.10.50 Release Notes, September, 2011 (Differences from Release A.10.03) 21

A.10.03 Release Notes, April, 2011 (Differences from Release A.10.02) 22

A.10.02 Release Notes, December, 2010 (Differences from Release A.10.01) 22

A.10.01 Release Notes, September, 2010 (Differences from Release A.10.00) 22

A.10.00 Release Notes, July, 2010 (Differences from Release A.09.00) 23

86100C-Only Firmware Release Notes 24

A.10.82 Release Notes, May, 2013 (Differences from Release A.09.01) 24

A.09.01 Release Notes, July, 2010 (Differences from Release A.09.00) 24

A.09.00 Release Notes, June 10, 2010 (Differences from Release A.08.10) 24

A.08.10 Release Notes, April 8, 2009 (Differences from Release A.08.00) 25

A.08.00 Release Notes, June 18, 2008 (Differences from Release A.07.00) 25

A.07.00 Release Notes, March 15, 2007 (Differences from Release A.06.01) 28

A.06.01 Release Notes, September 21, 2006 (Differences from Release A.06.00) 29

86100C/86100B/86100A Firmware Release Notes 31

A.05.00 Release Notes, February 16, 2005 (Differences from Release A.04.20) 31

A.04.20 Release Notes, June 9, 2005 (Differences from Release A.04.11) 31

A.04.11 Release Notes, December 10, 2004 (Differences from Release A.04.10) 33

A.04.10 Release Notes, November 1, 2004 (Differences from Release A.04.01) 34

A.04.01 Release Notes, June 23, 2004 (Differences from Release A.04.00) 36

A.04.00 Release Notes, February 19, 2004 (Differences from Release A.03.05) 36

A.03.04 Release Notes, October 10, 2002 (Differences from Release A.03.03) 39

A.03.03 Release Notes, July 18, 2002 (Differences from Release A.03.03) 40

86100A-Only Firmware Release Notes 41

A.03.01 Release Notes, February 15, 2002 (Differences from Release A.02.20) 41

A.02.20 Release Notes, August 2, 2001 (Differences from Release A.02.10) 42

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

A.02.10 Release Notes, May 1, 2001 (Differences from Release A.02.01) 42

A.02.01 Release Notes, January 30, 2001 (Differences from Release A.02.00) 44

A.02.00 Release Notes, November 29, 2000 (Differences from Release A.01.22) 44

A.01.22 Release Notes, September 6, 2000 (Differences from Release A.01.21) 46

A.01.21 Release Notes, August 9, 2000 (Differences from Release A.01.20) 46

A.01.20 Release Notes, July 11, 2000 (Differences from Release A.01.13) 46

A.01.13 Release Notes, May 2, 2000 (Differences from Release A.01.12) 47

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

N1010A FlexDCA Firmware Release Notes

A.02.50 Release Notes, October, 2013

(Differences from Release A.02.02)

General Comments

• Edited the 86118A module specification topic for adjusted 86118- H01 the channel

skew specification and for information added concerning 86118- H02 module's

1 mm input connectors.

• Added specifications for the 86105D- 281 module.

• Added specifications for the 86115D- 282 module.

General Defects Fixed

• Fixed a memory leak in the precision timebase synchronization. This leak would

cause the instrument to report insufficient memory error messages after several

days.

• Fixed a bug that prevented use of the knobs on the 86112A- HBW module.

• Improved the precision timebase synchronization to be less sensitive to signal

drift.

New Feature List

• New Jitter Spectrum Analysis (JSA) memory and ability to save JSA data files

(*.jsax). This allows JSA data to be viewed offline.

• When the jitter database is saved to disk, JSA is included if Clock Recovery

Emulation (CRE) is active.

• New tail fit method available in Jitter Mode, which enables the following new

scalar measurements:

• BUI (rms) for ones and zeros

•BUI(δ-δ) for ones and zeros

•BUJ

•BUJ(rms)

• Ability to measure TJ (Total Jitter), DJ (Deterministic Jitter), RJ (Random Jitter),

J2, J5, and J9 on long patterns such as PRBS31. This is accomplished within

FlexDCA with an option 401 license but without the use of the option 401

spreadsheet. A new Advanced Eye tab is enabled in Eye/Mask Mode. This feature

requires the option 401 Advanced Eye Analysis Software license.

New Command Subsystem

•:JSAMemory

New :DISK Subsystem Programming Commands

• :DISK:JSANalysis:FNAMe

• :DISK:JSANalysis:RECall

• :DISK:JSANalysis:RECall:DESTination

• :DISK:JSANalysis:SAVE

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

New :DISPlay Subsystem Commands

• :DISPlay:JITTer:CCEdge

New :MEASure Subsystem Commands

• :MEASure:AMPLitude:BIROnes

• :MEASure:AMPLitude:BIROnes:LOCation

• :MEASure:AMPLitude:BIROnes:SOURce

• :MEASure:AMPLitude:BIROnes:STATus

• :MEASure:AMPLitude:BIROnes:STATus:REASon

• :MEASure:AMPLitude:BIRZeros

• :MEASure:AMPLitude:BIRZeros:LOCation

• :MEASure:AMPLitude:BIRZeros:SOURce

• :MEASure:AMPLitude:BIRZeros:STATus

• :MEASure:AMPLitude:BIRZeros:STATus:REASon

• :MEASure:AMPLitude:BUIOnes

• :MEASure:AMPLitude:BUIOnes:LOCation

• :MEASure:AMPLitude:BUIOnes:SOURce

• :MEASure:AMPLitude:BUIOnes:STATus

• :MEASure:AMPLitude:BUIOnes:STATus:REASon

• :MEASure:AMPLitude:BUIZeros

• :MEASure:AMPLitude:BUIZeros:LOCation

• :MEASure:AMPLitude:BUIZeros:SOURce

• :MEASure:AMPLitude:BUIZeros:STATus

• :MEASure:AMPLitude:BUIZeros:STATus:REASon

• :MEASure:AMPLitude:ISIHist:SAMPles?

• :MEASure:AMPLitude:RNPIhist:SAMPles?

• :MEASure:AMPLitude:SMEThod?

• :MEASure:AMPLitude:TIHist:SAMPles?

• :MEASure:EYE:DJ

• :MEASure:EYE:DJ:RJSTabilize

• :MEASure:EYE:DJ:RJSValue

• :MEASure:EYE:JN

• :MEASure:EYE:JN:RJSTabilize

• :MEASure:EYE:JN:RJSValue

• :MEASure:EYE:JN:SJN

• :MEASure:EYE:RJ

• :MEASure:EYE:TJ

• :MEASure:EYE:TJ:RJSTabilize

• :MEASure:EYE:TJ:RJSValue

• :MEASure:EYE:TJ:TJBer

• :MEASure:JITTer:BUJ

• :MEASure:JITTer:BUJ:LOCation

• :MEASure:JITTer:BUJ:SOURce

• :MEASure:JITTer:BUJ:STATus

• :MEASure:JITTer:BUJ:STATus:REASon

• :MEASure:JITTer:BUJRms

• :MEASure:JITTer:BUJRms:LOCation

• :MEASure:JITTer:BUJRms:SOURce

• :MEASure:JITTer:BUJRms:STATus

• :MEASure:JITTer:BUJRms:STATus:REASon

• :MEASure:JITTer:DDJHist:SAMPles?

• :MEASure:JITTer:DEFine:SMEThod

• :MEASure:JITTer:LJMode

• :MEASure:JITTer:RJPJhist:SAMPles?

• :MEASure:JITTer:SMEThod?

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

• :MEASure:JITTer:TJHist:SAMPles?

A.02.02 Release Notes, May, 2013

(Differences from Release A.02.00)

General Comments

• Improvements added to eye measurement algorithms.

• Support added for N1012A OIF CEI 3.0 Compliance and Debug Application version

2.00.

New Feature List

• Skew calibration added for 86118A H01 modules.

• Fixture deskew added for 86118A H01 modules.

• Ability to open legacy Color Grade-Gray Scale memory files (.cgs).

A.02.00 Release Notes, January, 2013

(Differences from Release A.01.80)

General Comments

• FlexDCA is now the 86100D's default user interface. The 86100D can be placed

in one of three configuratons: Standard, Hybrid, or Legacy.

• For working offline, the DCA's data simulation state is now integrated with

standard live channels. Open FlexDCA normally without using a command- line

switch.

• Added two example programs for performing calibrations. Each program illustrates

a different method of controling execution timing.

NOTE FlexDCA is compatible with Windows XP and Windows 7 but is not compatible with Windows 8.

New Feature List

• Ability to use one- slot mini modules.

• Added new N1045A one- slot mini- module with two or four remote electrical

heads.

• Extended Module feature to control supported external instruments (via LAN)

such as the N4877A clock data recovery and demultiplexer.

• Added automatic fixture deskew.

• Added Skew Calibration to remove difference in electrical length between the

remote sampling heads on N1045A and 86118A- H01 modules.

• Added automatic differential deskew to apply Hardware Skew to two differential

channels.

• Added probe support and setup to Standard configuration.

•InStandard configuration, the 86100D supports SCPI connectivity via GPIB, VXI-

- 11 LAN, Telnet, Sockets, and HiSlip.

• Ability to adjust the 86100D front- panel calibration output (DC Cal) voltage.

• Added Absolute and Square Root math operators.

• Added Decision Feedback Equalizer and Sin(X)/X signal- processing operators.

• Support for the N1014A SFF- 8431 Compliance Application.

• Added Undo, Redo, and History.

• Added new Ethernet Mask: 100G- SR10 10.3125

• Added new OIF- CEI masks and SFF- 8431 masks.

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

CALibrate Subsystem Programming Commands

• :CALibrate:CHAN:ENABled (new)

• :CALibrate:CHAN:STATus (new)

• :CALibrate:CHAN:STATus:DETails (new)

• :CALibrate:CHAN:STATus:DTEMperature (new)

• :CALibrate:CHAN:STATus:TIME (new)

•:CALibrate:OUTPut(new)

• :CALibrate:SKEW:SLOT:STARt (new)

• :CALibrate:SKEW:SLOT:STATus? (new)

• :CALibrate:SKEW:SLOT:STATus:DETails? (new)

• :CALibrate:SKEW:SLOT:STATus:DTEMperature? (new)

• :CALibrate:SKEW:SLOT:STATus:TIME? (new)

:CHANnel Subsystem Programming Commands

• :CHANnel:BANDwidth:FREQuency (new)

• :CHANnel:FSELect:RATE (new)

• :CHANnel:PROBe (new)

• :CHANnel:WAVelength:VALue (new)

:CRECovery Subsystem Programming Commands

• :CRECovery:CFRequency? (new)

• :CRECovery:TDENsity? (new)

•:CRECovery:OUTPut:DMODe(new)

:DISPlay Subsystem Programming Commands

• :DISPlay:JITTer:GRAPh:TYPE (new)

• :DISPlay:JITTer:GRAPh? (deprecated)

• :DISPLay:MDISplay:DOCK (new)

:EMODules Subsystem Programming Commands (new)

The :EMODules extended modules subsystem controls the connection of extended and simu-

lated modules.

• :EMODules:CRECovery:SADDress (new)

• :EMODules:CRECovery:VADDress (new)

• :EMODules:REConnect (new)

• :EMODules:SIMulator:SRATe (new)

• :EMODules:SLOT:ADDRess (new)

• :EMODules:SLOT:CONNect (new)

• :EMODules:SLOT:DISConnect (new)

• :EMODules:SLOT:SELection (new)

• :EMODules:SLOT:STATe (new)

:PTIMebase Subsystem Programming Commands

• :PTIMebase:RIPRogress (deprecated)

:SIMulator Subsystem Programming Commands (deprecated)

• This entire subsystem has been deprecated. Use the :SOUR subsystem instead.

:SOURce Subsystem Programming Commands (new)

The new :SOURce subsystem configures the source signal of extended and simulated modules.

•:SOURce:AMPLitude(new)

• :SOURce:DIFFerential (new)

•:SOURce:DRATe(new)

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

• :SOURce:FILTer:CUToff (new)

• :SOURce:FILTer:STATe (new)

• :SOURce:FILTer:TYPe (new)

•:SOURce:FNAMe(new)

• :SOURce:FUNCtion (new)

• :SOURce:INVert (new)

• :SOURce:JITTer:RJ (new)

• :SOURce:JITTer:STATe (new)

• :SOURce:NOISe:RN (new)

• :SOURce:NOISe:STATe (new)

•:SOURce:OENable(new)

• :SOURce:OFFSet (new)

• :SOURce:PATTern (new)

•:SOURce:WTYPe(new)

:SPRocess Subsystem Programming Commands

• :SPRocess:DFEQualizer:BANDwidth (new)

• :SPRocess:DFEQualizer:BANDwidth:AUTo (new)

• :SPRocess:DFEQualizer:CLKDelay (new)

• :SPRocess:DFEQualizer:DWAVeform (new)

• :SPRocess:DFEQualizer:TAPS (new)

• :SPRocess:DFEQualizer:TAPS:AUTo (new)

• :SPRocess:DFEQualizer:TAPS:COUNt (new)

• :SPRocess:DFEQualizer:TAPS:RECalculate (new)

• :SPRocess:DFEQualizer:TARGet:AUTo (new)

• :SPRocess:DFEQualizer:TARGet:LOWer (new)

• :SPRocess:DFEQualizer:TARGet:UPPer (new)

:SYSTem Programming Commands Subsystem

• :SYSTem:FCONfig (new)

• :SYSTem:GTLocal (new)

• :SYSTem:LAUNch (new)

• :SYSTem:TEMPerature (new)

• :SYSTem:UAUToscale (deprecated)

• :SYSTem:UDEFault (deprecated)

A.01.80 Release Notes, June, 2012

(Differences from Release A.01.70)

General Comments

• FlexDCA requires Agilent IO Libraries 16.2 or later. If you have a prior version

installed, it will be upgraded to version 16.2.

• FlexDCA requires the Agilent licensing system 4.3 or later. This includes "Agilent

License Manager", "Agilent ACCL Licensing", and "Agilent Host Processor Platform".

• Removed the Control menu. The Auto Scale, Run, Stop, Single, and Clear functions

can more easily be accomplished by clicking the buttons that are shown to the

right of the menu bar. The Undo Auto Scale command has been moved to the top

of the Setup menu.

New Feature List

• Ability to use 86100D DCA- X applications. Added the Apps menu to the menu

bar for launching applications.

N1010A FlexDCA and 86100A/B/C/D

Firmware Release Notes

• Support for the N1012A OIF CEI Compliance 3.0 Application and N1019A User

Defined Application Tool. The new menu also supports user- added shortcuts to

files and Windows applications.

• FlexDCA now includes the ability to take into account the effect of external

devices such as attenuators or transducers. With this feature, FlexDCA will report

waveform and measurement results referenced to the input of the external device

instead of the input of the oscilloscope channel. Additionally, if you have

configured external attenuator or transducer settings in the 86100C/D firmware,

they will be transferred to FlexDCA when using "Transfer Basic" on connection to

the DCA.

• New copy- to- clipboard buttons on the shortcut menus for pasting waveform

images or measurement data to external applications.

• Ability to find a bit sequence in a pattern waveform.

• Ability to select one of four color schemes for displaying color- grade persistence

waveforms. This includes a color scheme that matches the classic 86100A/B/C/D

firmware.

• Ability to select color or monochrome display of gray- scale persistence waveforms.

• The remote SCPI interface is fully supported on 64- bit operating systems.

• The bandwidth of a differential signal can be configured from a single drop- down

in the GUI.

• The message area can now be "docked" so that it is permanently visible. To enable

this feature, access the "Display Setup" dialog from the "Setup" menu. Near the

bottom of the "Appearance" tab is a checkbox called "Dock Message Area".

General Defects Fixed

• Changed the default trigger bandwidth on the 86100D- STR frame from "Filtered

Edge" to "Standard Edge".

• The waveform save feature will only allow you to save waveforms that are

currently displayed. Previously, waveforms that had been acquired but not

displayed could also be saved, which made it easy to accidently save the wrong

waveform.

• Fixed the remote command ":DISK:SIMage:SINClude" in eye mode.

• Fixed a defect that caused Precision Timebase Synchronization to take a very long

time to complete when a PRBS 23 pattern was in use.

Common Programming Commands

• *IDN? (revised)

:ACQuire Subsystem Programming Commands

• :ACQuire:RLENgth:AUTo (deprecated)

• :ACQuire:RLENgth:MODE (new)

• :ACQuire:SPBit:AUTo (deprecated)

•:ACQuire:SPBit:MODE(new)

:CHANnel Subsystem Programming Commands

• :CHANnel:ATTenuator:DECibels (new)

• :CHANnel:ATTenuator:RATio (new)

• :CHANnel:ATTenuator:RESet (new)

• :CHANnel:ATTenuator:STATe? (new)

• :CHANnel:TRANsducer:GAIN (new)

• :CHANnel:TRANsducer:OFFSet (new)

• :CHANnel:TRANsducer:STATe (new)

•:CHANnel:TRANsducer:UNITs(new)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de Agilent Technologies

Agilent Technologies

Agilent Technologies ProBER 2 Instrucciones de montaje

Agilent Technologies

Agilent Technologies 93000 SOC Series Guía de instalación

Agilent Technologies

Agilent Technologies 87050A Option K24 Manual

Agilent Technologies

Agilent Technologies InfiniiVision MSO6012A Manual de usuario

Agilent Technologies

Agilent Technologies 3000 Series Manual de usuario

Agilent Technologies

Agilent Technologies DSO-X-2024A Manual de usuario

Agilent Technologies

Agilent Technologies E7490A Manual de usuario

Agilent Technologies

Agilent Technologies MSO8104A Guía de inicio rápido

Agilent Technologies

Agilent Technologies N9360A Manual de usuario

Agilent Technologies

Agilent Technologies N5341A Manual de usuario

Agilent Technologies

Agilent Technologies Infiniium DCA Manual

Agilent Technologies

Agilent Technologies Agilent 34980A Manual de usuario

Agilent Technologies

Agilent Technologies U2802A Manual de usuario

Agilent Technologies

Agilent Technologies N9360A Manual del propietario

Agilent Technologies

Agilent Technologies 8156A Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies e6601a Instrucciones de instalación y funcionamiento

Agilent Technologies

Agilent Technologies 86100C Manual de usuario

Agilent Technologies

Agilent Technologies 85052D Manual

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Manual de usuario

Agilent Technologies

Agilent Technologies AuroraPresto Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Manual de usuario

Agilent Technologies

Agilent Technologies 2000 X-Series Manual de usuario

Agilent Technologies

Agilent Technologies 3070 Series Guía del usuario

Agilent Technologies

Agilent Technologies 54620 Series Instrucciones de funcionamiento y seguridad

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario

Ritmix

Ritmix RAT-701 Manual de usuario