Agilent Technologies 16442A Manual de usuario

User’s Guide

Agilent 16442A Test Fixture

Agilent Part No. 16442-90000

Printed in Japan January 2000

Edition 3

2 Agilent 16442A User’s Guide, Edition 3

Legal Notice

The information contained in this document is subject to change without notice.

This document contains information which is protected by copyright. All rights are

reserved. Reproduction, adaptation, or translation without prior written permission

is prohibited, except as allowed under the copyright laws.

•Product Warranty

Agilent Technologies warrant Agilent Technologies hardware, accessories and

supplies against defects in materials and workmanship for the period of one year

from the warranty start date specified below. If Agilent Technologies receive

notice of such defects during the warranty period, Agilent Technologies will, at

its option, either repair or replace products which prove to be defective.

Replacement products may be either new or like-new.

Warranty service of this product will be performed at Agilent Technologies.

Buyer shall prepay shipping charges to Agilent Technologies and Agilent

Technologies shall pay shipping charges to return the product to Buyer.

However, Buyer shall pay all shipping charges, duties, and taxes for products

returned to Agilent Technologies from another country.

Agilent Technologies do not warrant that the operation of Agilent Technologies

products will be uninterrupted or error free. If Agilent is unable, within a

reasonable time, to repair or replace any product to a condition as warranted,

customer will be entitled to a refund of the purchase price upon prompt return of

the product.

The Agilent Technologies products may contain remanufactured parts

equivalent to new in performance or may have been subject to incidental use.

The warranty period begins on the date of delivery or on the date of installation

if installed by Agilent Technologies. If customer schedules or delays Agilent

Technologies installation more than 30 days after delivery, warranty begins on

the 31st day from delivery.

Warranty does not apply to defects resulting from (a) improper or inadequate

maintenance or calibration, (b) software, interfacing, parts or supplies not

supplied by Agilent Technologies, (c) unauthorized modification or misuse, (d)

operation outside of the published environmental specifications for the product,

or (e) improper site preparation or maintenance.

Agilent 16442A User’s Guide, Edition 3 3

To the extent allowed by local law, the above warranties are exclusive and no

other warranty or condition, whether written or oral, is expressed or implied and

Agilent Technologies specifically disclaim any implied warranties or conditions

of merchantability, satisfactory quality, and fitness for a particular purpose.

Agilent Technologies will be liable for damage to tangible property per incident

up to the greater of $300,000 or the actual amount paid for the product that is the

subject of the claim, and for damages for bodily injury or death, to the extent

that all such damages are determined by a court of competent jurisdiction to

have been directly caused by a defective Agilent Technologies product.

To the extent allowed by local law, the remedies in this warranty statement are

customer’s sole and exclusive remedies. Expect as indicated above, in no event

will Agilent Technologies or its suppliers be liable for loss of date or for direct,

special, incidental, consequential (including lost profit or date), or other damage,

whether based in contract, tort, or otherwise.

For consumer transactions in Australia and New Zealand: the warranty terms

contained in this statement, except to the extent lawfully permitted, do not

exclude, restrict or modify and are in addition to the mandatory statutory rights

applicable to the sale of this product to you.

•Assistance

Product maintenance agreements and other customer assistance agreements are

available for Agilent Technologies products.

For any assistance, contact your nearest Agilent Technologies Sales Office.

•Certification

Agilent Technologies Inc. certifies that this product met its published

specifications at the time of shipment from the factory. Agilent further certifies

that its calibration measurements are traceable to the National Institute of

Standards and Technology (NIST), to the extent allowed by the Institute’s

calibration facility, and to the calibration facilities of other International

Standards Organization members.

•Safety Summary

The following general safety precautions must be observed during all phases of

operation, service, and repair of this instrument. Failure to comply with these

precautions or with specific warnings elsewhere in this manual may impair the

protections provided by the equipment. In addition, it violates safety standards

of design, manufacture, and intended use of the instrument. Agilent

Technologies Inc. assumes no liability for customer’s failure to comply with

these requirements.

4 Agilent 16442A User’s Guide, Edition 3

•GROUND THE INSTRUMENT

This is Safety Class I instrument. To minimize shock hazard, the instrument

chassis and cabinet must be connected to an electrical ground. The power

terminal and the power cable must meet International Electrotechnical

Commission (IEC) safety standards.

•DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the instrument in the presence of flammable gases or fumes.

Operation of any electrical instrument in such an environment constitutes a

definite safety hazard.

•KEEP AWAY FROM LIVE CIRCUITS

Operation personnel must not remove instrument covers. Component

replacement and internal adjustments must be made by qualified

maintenance personnel. Do not replace components with power cable

connected. Under certain conditions, dangerous voltages may exist even

with the power cable removed. To avoid injuries, always disconnect power

and discharge circuits before touching them.

•DO NOT SERVICE OR ADJUST ALONE

Do not attempt internal service or adjustment unless another person, capable

of rendering first aid and resuscitation, is present.

•DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT

Because of the danger of introducing additional hazards, do not install

substitute parts or perform any unauthorized modification to the instrument.

Return the instrument to a Agilent Technologies Sales and Service Office for

services and repair to ensure that safety features are maintained.

•DANGEROUS PROCEDURE WARNINGS

Warnings, such as example below, precede potentially dangerous procedures

throughout this manual. Instructions contained in the warnings must be

followed.

WARNING Dangerous Voltage, capable of causing death, are present in this instrument.

Use extreme caution when handling, testing, and adjusting.

Agilent 16442A User’s Guide, Edition 3 5

•Safety Symbols

The general definitions of safety symbols used on equipment or in manuals are

listed below.

Instruction manual symbol: the product will be marked with this symbol when it

is necessary for the user to refer to the instruction manual in order to protect

against damage to the instrument.

Indicates dangerous voltage and potential for electrical shock. Do not touch

terminals that have this symbol when instrument is on.

Protective conductor terminal. For protection against electrical shock in case of

a fault. Used with field wiring terminals to indicate the terminal which must be

connected to ground before operating equipment.

Frame or chassis terminal. A connection to the frame (chassis) of the equipment

which normally includes all exposed metal structures.

Indicates earth (ground) terminal.

Alternating current.

Direct current.

ON (Supply).

OFF (Supply).

STANDBY (Supply).

Means INSTALLATION CATEGORY I. Measurement terminals on the rear

panel comply with INSTALLATION CATEGORY I.

WARNING The warning sign denotes a hazard. It calls attention to a procedure, practice,

condition or the like, which, if not correctly performed or adhered to, could result in

injury or death to personal.

CAUTION The caution sign denotes a hazard. It calls attention to an operating procedure,

practice, condition or the like, which, if not correctly performed or adhered to, could

result in damage to or destruction of part or all of the product.

CAT 1

6 Agilent 16442A User’s Guide, Edition 3

•Herstellerbescheinigung

GEÄUSCHEMISSION

Lpa < 70 dB

am Arbeitsplatz

normaler Betrieb

nach DIN 45635 T. 19

•Manufacturer’s Declaration

ACOUSTIC NOISE EMISSION

Lpa < 70dB

operator position

normal operation

per ISO 7779

Printing History

Edition 1: February 1994

Edition 2: August 1997

Edition 3: January 2000

Agilent 16442A User’s Guide, Edition 3

User's Guide

2 Agilent 16442A User’s Guide, Edition 3

User's Guide

Agilent 16442A test fixture is designed for testing electronic devices. You mount

the suitable socket module on the 16442A, which allows you to easily connect

various devices (DUTs) to measurement units.

The 16442A has thirteen channels:

•6 source/monitor unit (SMU) channels

Up to 3 channels can be connected to SMUs by Kelvin connections.

•2 voltage source unit (VSU) channels

•2 voltage monitor unit (VMU) channels

•2 pulse generator unit (PGU) channels

•1 ground unit (GNDU) channel

This manual provides the following information.

•Introduction

•Operation

•Installation

•Maintenance

•Specifications

Agilent 16442A User’s Guide, Edition 3 3

User's Guide

Introduction

Agilent 16442A test fixture contains the following accessories:

Description Agilent

Part Number Quantity

1 test fixture 16442-60001 1

2 stabilizer (with two flathead screws) 16442-60002 2

3 carrying case for socket modules 16442-60101 1

4 miniature banana to pin plug connection

cable (black)

16442-61600 4

5 miniature banana to pin plug connection

cable (red)

16442-61601 4

6 miniature banana to pin plug connection

cable (blue)

16442-61602 4

7 pin plug to pin plug connection cable

(black)

16442-61603 3

8 pin plug to pin plug connection cable (red) 16442-61604 3

4 Agilent 16442A User’s Guide, Edition 3

User's Guide

Introduction

NOTE Inspecting the 16442A upon Receiving

When the 16442A arrives at your site, make sure that nothing is missing or

damaged. Unpack the carton, then check the contents against figure and table above.

(For details about furnished and optional accessories, refer to “Specifications”.)

If anything is missing or damaged, contact your nearest Agilent Technologies sales

office.

9 pin plug to pin plug connection cable (blue) 16442-61605 3

10 miniature banana to miniature clip

connection cable (black)

16442-61606 3

11 miniature banana to miniature clip

connection cable (red)

16442-61607 3

12 miniature banana to miniature clip

connection cable (blue)

16442-61608 3

13 miniature banana to miniature banana

connection cable (black)

16442-61609 3

14 miniature banana to miniature banana

connection cable (red)

16442-61610 3

15 miniature banana to miniature banana

connection cable (blue)

16442-61611 3

16 blank TeflonTM board 16058-60004 1

17 dual-in-line package socket module (28-pin) 16088-60002 1

18 axial lead package socket module 16088-60009 1

19 TO-package socket module (12-pin) 16088-60006 1

20 User's Guide (this document) 16442-90000 1

Description Agilent

Part Number Quantity

Tabla de contenidos

Otros manuales de Equipo de prueba de Agilent Technologies

Agilent Technologies

Agilent Technologies N5230AU-974 Manual de instalación y operación

Agilent Technologies

Agilent Technologies Infiniium Manual de usuario

Agilent Technologies

Agilent Technologies Agilent 34980A Instrucciones de instalación y funcionamiento

Agilent Technologies

Agilent Technologies E6651A Manual de usuario

Agilent Technologies

Agilent Technologies 16043A Manual de operación

Agilent Technologies

Agilent Technologies N9360A Manual de usuario

Agilent Technologies

Agilent Technologies E7495A RF Manual de instrucciones

Agilent Technologies

Agilent Technologies Ininiium 90000 Manual de usuario

Agilent Technologies

Agilent Technologies Option H48 Multiport Test Set Z5623A Manual

Agilent Technologies

Agilent Technologies Medalist x6000 Manual de usuario

Agilent Technologies

Agilent Technologies 85056A Manual

Agilent Technologies

Agilent Technologies InfiniiVision 7000B Series Manual de usuario

Agilent Technologies

Agilent Technologies 37907A Guía de instalación

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Manual

Agilent Technologies

Agilent Technologies 1153A Guía de solución de problemas

Agilent Technologies

Agilent Technologies Medalist x6000 Especificaciones

Agilent Technologies

Agilent Technologies 93000 SOC Series Guía de instalación

Agilent Technologies

Agilent Technologies E5515BU-863 Manual de instalación y operación

Agilent Technologies

Agilent Technologies Auroraduet N1726A Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Manual

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X- Series Guía de configuración

Agilent Technologies

Agilent Technologies 8920B Manual de usuario

Agilent Technologies

Agilent Technologies 8960 Series 10 Manual de usuario

Agilent Technologies

Agilent Technologies E6001A Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manual de usuario

Ritmix

Ritmix RAT-701 Manual de usuario