Agilent Technologies E8364-60102 Manual de instalación y operación

Agilent Part Number: E8364-90011

Printed in USA April 2007

Supersedes print date: January 2005

Installation Note

Source Attenuators and Bias Tees Upgrade Kit

For E8363A and E8364A PNA Series Microwave Network Analyzers

Network Analyzer

Model Number

Upgrade Kit

Part Number

E8363A, E8364A E8364-60102

2Installation Note E8364-90011

WARRANTY STATEMENT

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO

BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM

EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION

CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. AGILENT SHALL NOT BE

LIABLE FOR ERRORS OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE FURNISHING, USE, OR PERFORMANCE OF THIS DOCUMENT OR

ANY INFORMATION CONTAINED HEREIN. SHOULD AGILENT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE

SEPARATE AGREEMENT WILL CONTROL.

DFARS/Restricted Rights Notice

If software is for use in the performance of a U.S. Government prime contract or subcontract,

Software is delivered and licensed as “Commercial computer software” as defined in DFAR

252.227-7014 (June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as

“Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use, duplication or disclosure of Software is subject to

Agilent Technologies’ standard commercial license terms, and non-DOD Departments and

Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in

FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than

Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any technical data.

Safety Notes

The following safety notes are used throughout this document. Familiarize yourself with each

of these notes and its meaning before performing any of the procedures in this document.

WARNING

Warning denotes a hazard. It calls attention to a procedure which,

if not correctly performed or adhered to, could result in injury or

loss of life. Do not proceed beyond a warning note until the

indicated conditions are fully understood and met.

CAUTION

Caution denotes a hazard. It calls attention to a procedure that, if not

correctly performed or adhered to, could result in damage to or destruction

of the instrument. Do not proceed beyond a caution sign until the indicated

conditions are fully understood and met.

Installation Note E8364-90011 3

Getting Assistance from Agilent

By internet, phone, or fax, get assistance with all your test and measurement needs.

Contacting Agilent

Assistance with test and measurements needs and information on finding a local Agilent

office are available on the Web at:

www.agilent.com/find/assist

If you do not have access to the Internet, please contact your Agilent field engineer.

NOTE

In any correspondence or telephone conversation, refer to the Agilent product by

its model number and full serial number. With this information, the Agilent

representative can determine whether your product is still within its warranty

period.

4Installation Note E8364-90011

About Installing the Upgrade Kit

Description of Option UNL

This option adds a 60-dB step attenuator and a bias tee between the switch splitter and each

of the front panel test ports.

The step attenuators are used to adjust the power level to the device under test (DUT)

without changing the power in the reference path.

The bias tees provide a means of biasing active devices under test. DC bias for the bias tees is

provided through two rear-panel BNC connectors. These inputs are fused for protection.

Products affected. . . . . . . . . . . . . . . . . . . . . . . . . . E8363A and E8364A; all options

Installation to be performed by . . . . . . . . . . . . . . Agilent service center or personnel

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 1.5 hour

Estimated adjustment time . . . . . . . . . . . . . . . . . 0.5 hours

Estimated full instrument calibration time . . . . 4.5 hours

Installation Note E8364-90011 5

Items Included in the Upgrade Kit

Table 1 lists the parts included in this upgrade kit, Agilent part number E8364-60102. Check

the contents of your kit against this list. If any item is missing or damaged, contact Agilent

Technologies. Refer to “Getting Assistance from Agilent” on page 3.

Table 1 Contents of Option UNL Upgrade Kit (E8364-60102)

Ref.

Desig. Description Qty Part

Number

The following parts are required for all analyzers

Installation note (this document) 1 E8364-90011

Machine screw, M3.0 x 8 CWPNTX (for attaching attenuators) 4 0515-0372

Machine screw, M2.5 x 14 CWPNTX (for attaching bias tees) 4 0515-2141

Cable clamp 1 1400-1439

A36, A37 60-dB step attenuator 2 33325-60012

A38, A39 Bias tee (cable included) 2 5087-7233

Ribbon cable (for A36 step attenuator) 1 8121-0819

Ribbon cable (for A37 step attenuator) 1 8121-0119

W51 RF cable, A22 switch splitter to A36 step attenuator 1 E8364-20055

W52 RF cable, A22 switch splitter to A37 step attenuator 1 E8364-20056

W55 RF cable, A38 bias tee to A25 test port 1 coupler 1 E8364-20051

W56 RF cable, A39 bias tee to A26 test port 2 coupler 1 E8364-20052

The following parts are required for only analyzers without Option 014 installed

W7 RF cable, A23 detector to A28 channel R1 mixer 1 E8364-20079

W8 RF cable, A24 detector to A29 channel R2 mixer 1 E8364-20080

W53 RF cable, A36 step attenuator to A38 bias tee

2 E8364-20077

W54 RF cable A37 step attenuator to A39 bias tee

The following parts are required for only analyzers with Option 014 installed

Lower front panel overlay (Option UNL/014) 1 E8364-80011

W70 RF cable, RCVR R1 IN to A28 channel R1 mixer 1 E8364-20049

W71 RF cable, RCVR R2 IN to A29 channel R2 mixer 1 E8364-20050

W81 RF cable, A36 step attenuator to Port 1 SOURCE OUT 1 E8364-20053

W82 RF cable, A37 step attenuator to Port 2 SOURCE OUT 1 E8364-20054

W83 RF cable, PORT 1 CPLR THRU to A38 bias tee 1 E8364-20039

W84 RF cable, PORT 2 CPLR THRU to A39 bias tee 1 E8364-20040

6Installation Note E8364-90011

Installation Procedure for the Upgrade Kit

The network analyzer must be in proper working condition prior to installing this option. Any

necessary repairs must be made before proceeding with this installation.

WARNING

This installation requires the removal of the analyzer’s protective outer

covers. The analyzer must be powered down and disconnected from the

mains supply before performing this procedure.

Electrostatic Discharge Protection

Protection against electrostatic discharge (ESD) is essential while removing or connecting

cables or assemblies within the network analyzer.

Static electricity can build up on your body and can easily damage sensitive internal circuit

elements when discharged. Static discharges too small to be felt can cause permanent

damage. To prevent damage to the instrument:

•always wear a grounded wrist strap having a 1 MΩresistor in series with it when handling

components and assemblies.

•always use a grounded, conductive table mat while working on the instrument.

•always wear a heel strap when working in an area with a conductive floor. If you are

uncertain about the conductivity of your floor, wear a heel strap.

Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to

“Tools and Equipment Required for the Installation” on page 7 for part numbers.

Figure 1 ESD Protection Setup

Installation Note E8364-90011 7

Overview of the Installation Procedure

Step 1. Remove the Outer Cover

Step 2. Remove the Front Panel Assembly (Option 014 Only)

Step 3. Raise the Receiver Deck

Step 4. Remove the Existing Cables

Step 5. Install the Attenuators and Bias Tees

Step 6. Install the Option UNL Cables

Step 7. Lower and Fasten the Receiver Deck and Connect the Bias Tee Control Cables

Step 8. Replace the Lower Front Panel Overlay (Option 014 Only)

Step 9. Reinstall the Front Panel Assembly and Front Panel Jumpers (Option 014 Only)

Step 10. Reinstall the Outer Cover

Step 11. Enable Option UNL

Step 12. Perform Post-Upgrade Adjustments and Calibration

Tools and Equipment Required for the Installation

CAUTION

Use a 5/16-in torque wrench set to 10 in-lbs on all cable connections except the

front-panel connectors to which the front-panel jumpers attach (Option 014).

Use a 5/16-in torque wrench set to 21 in-lbs for these connections.

Equipment Required for Post-Upgrade Adjustments

Description Qty Part Number

T-8 TORX driver (set to 5 in-lbs) 1 N/A

T-10 TORX driver (set to 9 in-lbs) 1 N/A

T-20 TORX driver (set to 21 in-lbs) 1 N/A

5/16 in torque wrench (set to 10 in-lbs) 1 N/A

5/16 in torque wrench (set to 21 in-lbs) (Option 014 only) 1 N/A

ESD grounding wrist strap 1 9300-1367

5 ft grounding cord for wrist strap 1 9300-0980

2 x 4 ft conductive table mat and 15 ft grounding wire 1 9300-0797

ESD heel strap (for use with conductive floors) 1 9300-1308

Equipment Type Model or

Part Number

Alternate Model or

Part Number

Power meter E4418B/E4419B E4418A/E4419A

Power sensor, 2.4 mm 8487A None

Adapter, 2.4 mm (f) to 2.4 mm (f) 11900B 85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f) 85133C 85133E

8Installation Note E8364-90011

Step 1. Remove the Outer Cover

CAUTION

This procedure is best performed with the analyzer resting on its front handles

in the vertical position. Do not place the analyzer on its front panel without the

handles. This will damage the front panel assemblies.

Refer to Figure 2 for this procedure.

1. Disconnect the power cord (if it has not already been disconnected).

2. With a T-20 TORX driver, remove the strap handles (item ①) by loosening the screws

(item ②) on both ends until the handle is free of the analyzer.

3. With a T-20 TORX driver, remove the four rear panel feet (item ③) by removing the center

screws (item ④).

4. Slide the four bottom feet (item ⑤) off the cover.

5. Slide the cover off of the frame.

Figure 2 Outer Cover Removal

Installation Note E8364-90011 9

Step 2. Remove the Front Panel Assembly (Option 014 Only)

Refer to Figure 3 for this procedure.

1. Using a 5/16-inch wrench, remove the six front panel semirigid jumper cables (item ①).

2. With a T-10 TORX driver, remove the eight screws (item ②) from the sides of the frame.

CAUTION

Before removing the front panel from the analyzer, lift and support the front of

the analyzer chassis.

3. Slide the front panel over the test port connectors.

4. Disconnect the front panel interface ribbon cable (item ③) from the A3 front panel

interface board. The front panel is now free from the analyzer.

Figure 3 Front Panel Assembly Removal

10 Installation Note E8364-90011

Step 3. Raise the Receiver Deck

Refer to Figure 4 for this procedure.

1. Place the analyzer bottom-side up on a flat surface.

2. With a T-10 TORX driver, remove the four screws (item ①), securing the receiver deck.

3. Pull the latch pin (item ②) towards the center of the analyzer to release the receiver deck.

4. Lift the receiver deck to partially raise it, then release the latch pin (item ②). Lift the

receiver deck to its fully raised position and ensure that the latch pin latches in the raised

position.

Figure 4 Receiver Deck, Raising

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies 16441A R-Box Manual de usuario

Agilent Technologies

Agilent Technologies N1913a Manual de usuario

Agilent Technologies

Agilent Technologies E5071C Manual de usuario

Agilent Technologies

Agilent Technologies Cary 100 Manual de usuario

Agilent Technologies

Agilent Technologies 8753ET Manual de usuario

Agilent Technologies

Agilent Technologies 1660C Series Manual de usuario

Agilent Technologies

Agilent Technologies 8719ET Manual

Agilent Technologies

Agilent Technologies FRG-700 Manual de usuario

Agilent Technologies

Agilent Technologies 8702D Manual de usuario

Agilent Technologies

Agilent Technologies E5072A ENA Series Manual de usuario

Agilent Technologies

Agilent Technologies 4338B Manual de usuario

Agilent Technologies

Agilent Technologies 81950A Manual de usuario

Agilent Technologies

Agilent Technologies ENA Series Manual de usuario

Agilent Technologies

Agilent Technologies E4980A Manual de usuario

Agilent Technologies

Agilent Technologies 8720E Series Manual de usuario

Agilent Technologies

Agilent Technologies E4440AU Manual de instalación y operación

Agilent Technologies

Agilent Technologies E5080 Series Manual de usuario

Agilent Technologies

Agilent Technologies 35670A Manual de usuario

Agilent Technologies

Agilent Technologies Acqiris DC110 Manual de usuario

Agilent Technologies

Agilent Technologies 89410A Manual de usuario

Agilent Technologies

Agilent Technologies 4291B Manual de usuario

Agilent Technologies

Agilent Technologies B1500A Guía de instalación

Agilent Technologies

Agilent Technologies BioTek Epoch 2 Manual de usuario

Agilent Technologies

Agilent Technologies B1500A Guía de instalación

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario