Agilent Technologies 8510XF Manual de servicio

8510XF Network Analyzer Systems

E7340A & E7342A (2 to 85 GHz)

E7350A & E7352A (2 to 110 GHz)

Operating and Service

Manual

Agilent Part Number: E7350-90001

Printed in USA

Print Date: April 2002

Supersedes: June 2001

ii 8510XF Network Analyzer Systems

Notice

The information contained in this document is subject to change without

notice.

Agilent Technologies makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and ﬁtness for a particular purpose. Agilent Technologies

shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or

use of this material.

Agilent Technologies assumes no responsibility for the use or reliability of

its software on equipment that is not furnished by Agilent Technologies.

This document contains proprietary information which is protected by

photocopied, reproduced, or translated to another language without prior

written consent of Agilent Technologies.

Restricted Rights Legend

Use, duplication, or disclosure by the U.S. Government is subject to

restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical

Data and Computer Software clause at DFARS 252.227-7013 for DOD

agencies, and subparagraphs (c)(1) and (c)(2) of the Commercial Computer

Software Restricted Rights clause at FAR 52.227-19 for other agencies.

Hewlett-Packard to Agilent Technologies Transition

This documentation supports a product that previously shipped under the

Hewlett-Packard company brand name. The brand name has now been

changed to Agilent Technologies. The two products are functionally

identical, only our name has changed. This document still includes

references to Hewlett-Packard products, some of which have been

transitioned to Agilent Technologies.

Windows ® is a registered copyright of Microsoft corporation.

8510XF Network Analyzer Systems iii

What You’ll Find in This Manual…

Chapter 1 •Introduction to the 8510XF

Chapter 2 •How to install the system

Chapter 3 •How to use the system to make measurements

Chapter 4 •How to verify the performance of the system

Chapter 5 •How to maintain the system

Chapter 6 •How to order replacement parts

Chapter 7 •How to ﬁnd information about menus, softkeys, and commands

iv8510XF Network Analyzer Systems

Warranty

Certiﬁcation Agilent Technologies certiﬁes that this product met its published

speciﬁcations at the time of shipment from the factory. Agilent Technologies

further certiﬁes that its calibration measurements are traceable to the

United States National Institute of Standards and Technology (NIST,

formerly NBS), to the extent allowed by the Institute’s calibration facility,

and to the calibration facilities of other International Standards

Organization members.

DOCUMENTATION

WARRANTY THE MATERIAL CONTAINED IN THIS DOCUMENT IS

PROVIDED "AS IS," AND IS SUBJECT TO BEING CHANGED,

WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO

THEMAXIMUMEXTENTPERMITTEDBYAPPLICABLELAW,

AGILENTDISCLAIMSALLWARRANTIES,EITHEREXPRESS

OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY

INFORMATIONCONTAINEDHEREIN,INCLUDINGBUTNOT

LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. AGILENT SHALL NOT BE LIABLE FOR ERRORS

OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE FURNISHING, USE, OR

PERFORMANCE OF THIS DOCUMENT OR ANY

INFORMATION CONTAINED HEREIN. SHOULD AGILENT

ANDTHEUSERHAVEASEPARATEWRITTENAGREEMENT

WITH WARRANTY TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT WITH THESE TERMS,

THE WARRANTY TERMS IN THE SEPARATE AGREEMENT

WILL CONTROL.

Assistance Product maintenance agreements and other customer assistance agreements

are available for Agilent Technologies products.

For assistance, call your local Agilent Technologies ofﬁce (see“Contacting

Agilent”)

8510XF Network Analyzer Systems v

Contacting Agilent

Online assistance: www.agilent.com/find/assist

United States

(tel) 1 800 452 4844 Latin America

(tel) (305) 269 7500

(fax) (305) 269 7599

Canada

(tel) 1 877 894 4414

(fax) (905) 282-6495

Europe

(tel) (+31) 20 547 2323

(fax) (+31) 20 547 2390

New Zealand

(tel) 0 800 738 378

(fax) (+64) 4 495 8950

Japan

(tel) (+81) 426 56 7832

(fax) (+81) 426 56 7840

Australia

(tel) 1 800 629 485

(fax) (+61) 3 9210 5947

Singapore

(tel) 1 800 375 8100

(fax) (65) 836 0252

Malaysia

(tel) 1 800 828 848

(fax) 1 800 801 664

Philippines

(tel) (632) 8426802

(tel) (PLDT subscriber only):

1 800 16510170

(fax) (632) 8426809

(fax) (PLDT subscriber only):

1 800 16510288

Thailand

(tel) outside Bangkok:

(088) 226 008

(tel) within Bangkok:

(662) 661 3999

(fax) (66) 1 661 3714

Hong Kong

(tel) 800 930 871

(fax) (852) 2506 9233

Taiwan

(tel) 0800-047-866

(fax) (886) 2 25456723

People’s Republic of

China

(tel) (preferred):

800-810-0189

(tel) (alternate):

10800-650-0021

(fax) 10800-650-0121

India

(tel) 1-600-11-2929

(fax) 000-800-650-1101

vi 8510XF Network Analyzer Systems

Safety and Regulatory Information

Review this product and related documentation to familiarize yourself with

safety markings and instructions before you operate the instrument. This

product has been designed and tested in accordance with international

standards.

WARNING The WARNING notice denotes a hazard. It calls attention to a procedure,

practice, or the like, that, if not correctly performed or adhered to, could result

in personal injury. Do not proceed beyond a WARNING notice until the

indicated conditions are fully understood and met.

CAUTION The CAUTION notice denotes a hazard. It calls attention to an operating

procedure, practice, or the like, which, if not correctly performed or adhered

to, could result in damage to the product or loss of important data. Do not

proceed beyond a CAUTION notice until the indicated conditions are fully

understood and met.

8510XF Network Analyzer Systems vii

Safety and Regulatory Information

Instrument Markings

Safety Requirements This product has been designed and tested in accordance with the IEC

Publication 1010, Safety Requirements for Electronic Measuring Apparatus,

and has been supplied in a safe condition. The instruction documentation

contains information and warnings which must be followed by the user to

ensure safe operation and maintain the product in a safe condition.

Safety Earth

Ground This is a Safety Class I product (provided with a protective earthing

terminal). An uninterruptible safety earth ground must be provided from the

main power source to the product input wiring terminals, power cord, or

supplied power cord set. Whenever it is likely that the protection has been

impaired, the product must be made inoperative and secured against any

unintended operation.

When you see this symbol on your instrument, you should refer to the instrument’s

instruction manual for important information.

This symbol indicates hazardous voltages.

The laser radiation symbol is marked on products that have a laser output.

This symbol indicates that the instrument requires alternating current (ac) input.

The C-Tick mark is a registered trademark of the Australian Spectrum Agency.

The CE mark is a registered trademark of the European Community. If it is

accompanied by a year, it indicates the year the design was proven.

The CSA mark is a registered trademark of the Canadian Standards Association.

1SM1-A This text indicates that the instrument is an Industrial Scientiﬁc and Medical Group 1

Class A product (CISPER 11, Clause 4).

This ISM device complies with Canadian ICES-001.

Cet apppareil ISM est conforme a la norme NMB du Canada.

This symbol indicates that the power line switch is ON.

This symbol indicates that the power line switch is OFF or in STANDBY position.

viii 8510XF Network Analyzer Systems

Safety and Regulatory Information

Before Applying Power Verify that the product is conﬁgured to match the available main power

source as described in the input power conﬁguration instructions in this

manual. If this product is to be powered by autotransformer, make sure the

common terminal is connected to the neutral (grounded) side of the ac power

supply.

WARNING Danger of explosion if battery is incorrectly replaced. Replace only with the

same or equivalent type recommended. Discard used batteries according to

manufacturers’s instructions.

NOTE Please refer to the 8510C On-Ssite Service Manual for additional

information (part number 08510-90282).

8510XF Network Analyzer Systems ix

Typeface Conventions

Italics •Used to emphasize important information:

Use this software only with the xxxxxX system.

•Used for the title of a publication:

Refer to the xxxxxX System-Level User’s Guide.

•Used to indicate a variable:

Type LOAD BIN ﬁlename.

Instrument Display •Used to show on-screen prompts and messages that you will see on the

display of an instrument:

The xxxxxX will display the message CAL1 SAVED.

[Keycap] •Used for labeled keys on the front panel of an instrument or on a

computer keyboard:

Press [Return].

{Softkey} •Used for simulated keys that appear on an instrument display:

Press {Prior Menu}.

User Entry •Used to indicate text that you will enter using the computer keyboard;

text shown in this typeface must be typed exactly as printed:

Type LOAD PARMFILE

•Used for examples of programming code:

#endif // ifndef NO_CLASS

Path Name

•Used for a subdirectory name or ﬁle path:

Edit the ﬁle

usr/local/bin/sample.txt

Computer Display •Used to show messages, prompts, and window labels that appear on a

computer monitor:

The Edit Parameters window will appear on the screen.

•Used for menus, lists, dialog boxes, and button boxes on a computer

monitor from which you make selections using the mouse or keyboard:

Double-click EXIT to quit the program.

x 8510XF Network Analyzer Systems

Compliance with Standards

Compliance with German Noise Requirements

This is to declare that this instrument is in conformance with the German

Regulation on Noise Declaration for Machines (Laermangabe nach der

Maschinenlaermrerordnung −3.GSGV Deutschand).

Compliance with EEC Directives

See the declaration of conformity on the following page.

Acoustic Noise Emission/Geraeuschemission

LpA <70 dB

Operator position

Normal position

per ISO 7779

LpA <70 dB

am Arbeitsplatz

normaler Betrieb

nach DIN 45635 t.19

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies 8712ET Manual de usuario

Agilent Technologies

Agilent Technologies 2100 Bioanalyzer System Manual de usuario

Agilent Technologies

Agilent Technologies U1701A Manual de usuario

Agilent Technologies

Agilent Technologies Agilent 4396B Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies 11867A? Manual de servicio

Agilent Technologies

Agilent Technologies B1500A Manual de usuario

Agilent Technologies

Agilent Technologies 3200P Manual de usuario

Agilent Technologies

Agilent Technologies N2797A Manual de usuario

Agilent Technologies

Agilent Technologies BioTek Epoch 2 Manual de usuario

Agilent Technologies

Agilent Technologies E5071C Manual de usuario

Agilent Technologies

Agilent Technologies ESA-L1500A Guía de inicio rápido

Agilent Technologies

Agilent Technologies E8356A Manual de instalación y operación

Agilent Technologies

Agilent Technologies 4338B Manual de usuario

Agilent Technologies

Agilent Technologies 8504B Manual de usuario

Agilent Technologies

Agilent Technologies E5900B Manual de usuario

Agilent Technologies

Agilent Technologies ADM1000 Manual de usuario

Agilent Technologies

Agilent Technologies 85052A Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies FieldFox MW N9913A Manual de usuario

Agilent Technologies

Agilent Technologies 1290 Infinity II 2D-LC Solution Manual de usuario

Agilent Technologies

Agilent Technologies U1731B Manual

Agilent Technologies

Agilent Technologies 85024A Manual

Agilent Technologies

Agilent Technologies 85032B/E 50 Manual

Agilent Technologies

Agilent Technologies 83438A Manual de usuario

Agilent Technologies

Agilent Technologies E4417A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario