Agilent Technologies Medalist i1000 Manual de usuario

Agilent Technologies

Medalist i1000 In-circuit

Test System

Installation Guide

Notices

No part of this manual may be reproduced

in any form or by any means (including

electronic storage and retrieval or

translation into a foreign language) without

prior agreement and written consent from

Agilent Technologies, Inc. as governed by

United States and international copyright

laws.

Manual Part Number

U9401-96000

Edition

First edition, September 2007

Printed in Taiwan

Agilent Technologies, Inc.

1601 California Street

Palo Alto, CA 94304 USA

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connection

with the furnishing, use, or perfor-

mance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a

license and may be used or copied only in

accordance with the terms of such license.

Restricted Rights Legend

If software is for use in the performance of

a U.S. Government prime contract or sub-

contract, Software is delivered and

licensed as “Commercial computer soft-

ware” as defined in DFAR 252.227-7014

(June 1995), or as a “commercial item” as

defined in FAR 2.101(a) or as “Restricted

computer software” as defined in FAR

52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use,

duplication or disclosure of Software is

subject to Agilent Technologies’ standard

commercial license terms, and non-DOD

Departments and Agencies of the U.S. Gov-

ernment will receive no greater than

Restricted Rights as defined in FAR

52.227-19(c)(1-2) (June 1987). U.S. Govern-

ment users will receive no greater than

Limited Rights as defined in FAR 52.227-14

(June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any

technical data.

Safety Notices

WARNING

A WARNING notice with this sym-

bol indicates a risk of electric

shock. The operator must follow

the instructions carefully to avoid

electric shock.

WARNING

A WARNING notice calls attention

to a procedure, practice, or condi-

tion which could possibly cause

bodily injury or death.

CAUTION

A CAUTION notice calls attention

to a procedure, practice, or condi-

tion which could possibly cause

damage to the equipment of per-

manent loss of data.

Medalist i1000 In-circuit Test System

Installation Guide

Medalist i1000 Installation Guide

Safety Precautions 2

Front Panel Access 3

Installation Overview 6

Preparing the Power Cord 8

Hardware Installation 11

Software Installation 18

Control Buttons 19

Installing the Fixture on the Press Down Model (U9401A) 20

Installing the Fixture on the Vacuum Model (U9402A) 24

System Check 31

Adjusting Fixture Press Travel on the Press Down Model (U9401A) 32

This guide describes how to install the Medalist i1000 In- circuit Test

Systems. Procedures are provided for both the press down model (U9401A)

and the vacuum model (U9402A).

2Medalist i1000 Installation Guide

Safety Precautions

WARNING Installation

Before you turn on the power, verify that the ac mains supply voltage matches

the voltage marked on the system specifications plate on the back of the

equipment.

This equipment must be connected to a properly installed earth ground. Do not

operate the equipment until it has been properly earthed by a qualified

electrician.

Overcurrent protection must be provided for this equipment. Do not operate

the equipment until proper overcurrent protection has been installed by a

qualified electrician.

This equipment is not intended for use near explosive or corrosive hazards.

CAUTION Servicing

All fuses must be replaced only with fuses of the specified type. Do not modify

the equipment or use unapproved replacement parts.

Medalist i1000 Installation Guide 3

Front Panel Access

The front panel of the Medalist i1000 provides access to the power

switches and cards in the testhead. The front panel can also be removed

when servicing is required.

•Opening the Front Panel

•Removing the Front Panel

•Replacing the Front Panel

Opening the Front Panel

1The front panel has two recessed handles, one on each side of the

panel. Push the bottom of the handle on the front panel as shown in

Figure 1 and rotate the handle out from its recessed position. Do the

same on the other side of the front panel.

2Latches on the inside of the front panel secures the panel in place. You

have to open the side panel to reach and unfasten the latch (Figure 2).

Do the same on the other side of the test station.

Figure 1 Handle on front panel

Figure 2 Unlock front panel

Location of latch

4Medalist i1000 Installation Guide

3Hold the handles of the front panel and pull towards you. The front

panel opens from the top and is supported by two cables when fully

open (Figure 3).

With the door in this position, you will be able to access the power

switches and replace any cards.

Removing the Front Panel

If the front panel needs to be removed, continue with the following steps.

1Support the front panel while you loosen the screws that secure the

supporting cables to the test station (Figure 4). Then unhook the cables

from the screws.

2Once the supporting cables are released, use the handles to lift the

front panel upwards and away from the test station.

Figure 3 Front panel open

supporting

cable

Figure 4 Unfasten supporting cables

Medalist i1000 Installation Guide 5

Replacing the Front Panel

Follow these steps to replace the front panel:

1There are two pins at the bottom of the front panel. Fit the pins into

the corresponding holes at the bottom front edge of the test station

(Figure 5).

2Support the front panel while you loop the supporting cables over the

screws (Figure 3). Tighten the screws to secure the cables.

3Close the front panel.

4Open the side panels and secure the latches on the inside of the front

panel.

Figure 5 Replace front panel

Figure 6 Secure supporting cables

fit pin into this hole

6Medalist i1000 Installation Guide

Installation Overview

Figure 7 shows where the hardware components are installed on the

U9401A (press down model). On the U9402A (vacuum model), the

controller is installed in the same location.

Figure 7 U9401A (press down model)

1Press Down Unit

2Sensors

3Fixture

4Debug probe/ESD ground connector

5CPU

6Monitor, keyboard, and mouse

Medalist i1000 Installation Guide 7

Before you begin installation, prepare the power cable for the system.

Refer to the instructions in “Preparing the Power Cord” on page 8. Then

continue with the installation procedure for your system:

•Installation Procedure for Press Down Model (U9401A)

•Installation procedure for Vacuum Model (U9402A)

Installation Procedure for Press Down Model (U9401A)

1Install the Press Down Unit (U9401A)

2Install the Controller

3Connect the Debug Probe

4Connect Power and Compressed Air Supply

5Power Up the System

6Install Medalist i1000 Software

7Install the Fixture

8Align the Safety Sensors

9Perform a System Check

Installation procedure for Vacuum Model (U9402A)

1Install the Controller

2Connect the Debug Probe

3Connect Power and Compressed Air Supply

4Power Up the System

5Install Medalist i1000 Software

6Install the Fixture

7Perform a System Check

8Medalist i1000 Installation Guide

Preparing the Power Cord

To assemble the power cord, follow these steps:

1Locate the power connector provided (Figure 8).

2Loosen the two screws holding the cable retainer at the back of the

power connector. Then unscrew the black connector insert to separate

it from the metal casing (Figure 9).

WARNING The Medalist i1000 is shipped without a power cord. This allows local support

engineers to purchase a power cord that is suitable for use in the facility

where the system is installed and meets the regulatory requirements of the

country.

Be sure to purchase a power cord rated to operate at 200~240 VAC and

10 Amps, with a minimum length of 2.5 m.

Figure 8 Power connector

Figure 9 Remove black connector insert

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Agilent Technologies

Agilent Technologies

Agilent Technologies 7673 Manual de usuario

Agilent Technologies

Agilent Technologies 7890 Series Manual de usuario

Agilent Technologies

Agilent Technologies G1701EA Manual de usuario

Agilent Technologies

Agilent Technologies 5975 Series Manual de usuario

Agilent Technologies

Agilent Technologies 8860 Hoja de instrucciones

Agilent Technologies

Agilent Technologies Intuvo 9000 Hoja de instrucciones

Agilent Technologies

Agilent Technologies IMG-500 Manual de usuario

Agilent Technologies

Agilent Technologies G3199 Series Manual de usuario

Agilent Technologies

Agilent Technologies 7010 Series Manual de usuario

Agilent Technologies

Agilent Technologies Graphite Tube Atomizer GTA 120 Manual de usuario

Agilent Technologies

Agilent Technologies NovoCyte Quanteon Manual

Agilent Technologies

Agilent Technologies 8860 Manual de usuario

Agilent Technologies

Agilent Technologies G2545A Manual de uso y cuidado

Agilent Technologies

Agilent Technologies 7890B Manual de usuario

Agilent Technologies

Agilent Technologies 83620A Manual de usuario

Agilent Technologies

Agilent Technologies 1290 infinity Manual de usuario

Agilent Technologies

Agilent Technologies 1200 series Manual de usuario

Agilent Technologies

Agilent Technologies 53150A Manual de usuario

Agilent Technologies

Agilent Technologies PSG Series Manual de usuario

Agilent Technologies

Agilent Technologies Varian 3800 GC Manual de usuario

Agilent Technologies

Agilent Technologies GPC/SEC Manual de usuario

Agilent Technologies

Agilent Technologies 1260 Infinity Manual de usuario

Agilent Technologies

Agilent Technologies InfinityLab LC Series Manual de usuario

Agilent Technologies

Agilent Technologies 100 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario

Yamato

Yamato BM510 Manual de usuario