AES 605 Manual de instrucciones

P a g e | 1

Installation & User Manual

For

605 D E C T + 2 . 4 G I n t e r c o m

Wireless Video Intercom System

Models 605AB, 605ABK

P a g e | 2

Contents

Overview of system

…………….Pg 3

Site Survey

…………….Pg 3

Mounting the Transmitter

…………….Pg 3

Power supply

…………….Pg 3

Mounting Architectural Panels

…………….Pg 4

Mounting Hooded Panels

…………….Pg 4

Mounting Flush Panels

…………….Pg 4

Wiring

…………….Pg 5

Code Lock Keypad Connections

…………….Pg 5

Wiring Tips

…………….Pg 6

Keypad Overview

…………….Pg 6

Basic Keypad Programming

…………….Pg 7

Full Keypad programming

…………….Pg 7

Using the Keypad

…………….Pg 9

The Handset

…………….Pg 9

Recoding / Adding a Handset

…………….Pg 9

Testing

.………….Pg 10

Using the Intercom Handset

.………….Pg 10

Maintenance of the Intercom

.………….Pg 10

Troubleshooting

.………….Pg 11

P a g e | 3

Overview of System

Please read this entire manual before attempting to install this system.

This system should only be installed by a professional automatic gate installer or access control

specialist installer.

It is recommended that the system be range tested on site BEFORE being fully installed.

Site Survey

Before installing this system, you need to be sure that the range of the system will be sufficient.

The transmitter and speech unit can be powered up, call button pressed, and then check that the

handset will ring from all areas in which it will be used.

Tip: For longer range installations, locate the handset close to the front of the property, near a

window if possible. Concrete walls can reduce the open air range of 350 metres by 30-50% per

wall.

Installation

Assuming satisfactory operation at full range, you are ready to fully install the product.

Mount the intercom at the desired height for pedestrian or car users. The camera angle

is wide at 90 degrees to cover most scenarios.

Loosen top 2 screws only

Hinge front door

Side View

Tip: Do not drill holes in the wall with the intercom in positon, otherwise dust may get

around the camera window and impair the camera view.

P a g e | 4

Mounting the Antenna

Mount the antenna as high as possible to achieve longest range.

TIP: Antenna beam width is approximately 40 degrees. For short range door

intercoms, ask your distributor or dealer for an omni-pole type antenna with 360 degree

beam angle.

Power Supply

TIP: Most technical calls received are due to installers using CAT5 or alarm cable

to power the unit. Neither are rated to carry enough power (1.5 amp peak). Please

use following cable sizes…

Up to 2 metres (6 feet) –Use minimum 0.75mm2(18 gauge)

Up to 4 metres (12 feet) –Use minimum 1mm2(16 gauge)

Up to 8 metres (24 feet) –Use minimum 1.5mm2(14 gauge)

Excessively long

cable!!

Power supply

Call point

Mains power Power supply

Call point

P a g e | 5

Wiring

Wiring Tips

Note: The manufacturer can only support the use, operation and functionality of the

intercom and keypad themselves. Professional wiring to door release or automatic gate

N/C

COM

N/O

N/C

Data I/O

N/O

egress

OUT1 OUT2

OUT3 N/C

COM

N/O K or A

Sense

Tamper

N/C

DU out

(-)GND

OUT2

Relay

Select N/ON/C

P a g e | 6

systems is the responsibility of the installer. Please consult a security integrator for

further support.

Advanced Keypad Connections

N/C

COM

N/O

N/C

Data I/O

N/O

egress

OUT1 OUT2

OUT3 N/C

COM

N/O K or A

Sense

Tamper

N/C

DU out

(-)GND

O/P1 inhib

INT Lock

OUT2

Relay

Select N/ON/C

12v DC

From Power

Supply

Keypad overview

This keypad has 3 outputs. The diagram below shows the LED indicators which indicate

programming and relay status information.

RED when incorrect codes entered and outputs are locked out.

1 2 3

4 5 6

7 8 9

* 0 #

SLOW FLASHING - in normal standby mode.

ON in programming mode.

ON when relay 3 activated.

GREEN when output 1 activated.

RED when output 2 activated.

CLEAR when output 3 activated

FAST FLASHING –Wrong code entered / error.

TIP: After power up, as a security precaution, the keypad cannot be programmed for 60 seconds.

Once this time elapses, you may begin.

TIP: Flashing amber LED is normal standby mode!

Advanced connections

INT Lock –Used to operate a door in conjunction with

another keypad. 24v dc max voltage, 100mA sink.

O/P1 inhib –When closed, this disables all codes for

relay group 1.

Sense –N/C connected to (-)GND, to be connected to

N/C door contact. Can be used to generate door open or

tamper alarm.

DU out –switches to (-) ground after the Duress Code is

entered. Used to trigger alarm zone, or buzzer to notify

guard. 100mA sink, 24VDC.

K or A –Not used.

DATA I/O PORT (Data Communication Bus) The Data I/O port is

prepared for setting up a data bus for the connection of the auxiliary reader-

keypads and the split-decoder in system expansion

P a g e | 7

Basic Keypad Programming

0 0 0 0 * *

Quick start guide

1) Enter programming mode (amber LED should be ON)

1 0 2 0 0 ? ?? ? #0

2) Enter a new user code...

* *

3) Exit programming mode

4) Enter the new user code to check the relay clicks.

Full Keypad programming

Enter programming mode..

0 0 0 0 * *

Exit programming mode..

* *

Enter a new ENGINEERS code…

Go into programming mode firstly then enter the following sequence…

Location

0 1 ?? ? ?

4-8 digit code Validate

Enter or delete new user codes

There are 3 groups of user codes. Group 10 for relay 1, group 20 for relay 2, and group 30 for

relay 3. The programming sequence is shown below…

Memory locations

000-999 for relay 1

001-100 for relay 2

001-100 for relay 3

1 0 2 0 0

10= relay 1 codes

(1000 available)

20= relay 2 codes

(100 available)

30= relay 3 codes

(100 available)

? ?? ? #0

2= add code

5= delete code Pin code 4-8 digits Validate

Example: Add user 31 to have access code 5555 operating relay 2….

2 0 2 0 3 5 55 5 #1

Group 2 Add code Location 31 Pin code 5555 Validate

Programming relay output times and modes…

Tip: The engineer code

must be the same length as

user codes. So if using a 6

digit engineers code, then

user codes must also be 6

digits long etc.

The unit is now in programming mode. Amber LED on the

keypad should remain permanently on. 0000 is the default

programming passcode.

The unit should exit programming mode and the amber LED

should start flashing again.

Replace ???? with your new ENGINEERS

code.

P a g e | 8

? ? 01 -

0 = start / stop toggle mode (latching)

1-99999 = seconds momentary operation

99999

or #

51=relay1

52=relay2

53=relay3

Validate

Delete a user code even if you don’t know the code…

? ? 5 ? ?? #

10=relay1

20=relay2

30=relay3 Delete code ID location to be deleted Validate

Delete an entire group of codes

? ? 0 9 99 #

10=relay1 group

20=relay2 group

30=relay3 group Super delete code Validate

Programming super user codes…

A super user code can activate any of the 3 relays

Location

0 2 ?? ? ?

4-8 digit code Validate

Restoring defaults

When in programming mode, you can enter the following sequence…

9 9 99 #

When the master code is forgotten….

1) Wire a push button (or replicate with wire link) across the Egress terminal and (-)GND.

2) Switch off power for 1 minute.

3) Switch ON power.

4) during the first 60 seconds, press the EG button once to enable the function.

5) Enter the following code..

8 0 08 * *

The keypad should now be in programming mode, ready to accept new data.

P a g e | 9

Using the keypad

Using the standard codes…

Once you have exited out of programming mode, simply enter the user code.

Using super user codes

?? ? ? # 1 Activate output 1

?? ? ? # 2 Activate output 2

?? ? ? # 3 Activate output 3

The Video Handset

The handset should be charged for 8 hours before use. It is recommended to give it at least 1

hour charge before range testing.

P a g e | 10

Answering Calls

1. When the intercom calls, identify the visitor on the screen.

40-80cm

2. Press the OK button to answer the call.

3. Speak clearly into the top of the handset at a distance of 10-20cm.

10cm

4. During the call press < or > to increase or decrease volume.

5. Press to activate door or gate release and press OK to end the call.

Note: The video will remain active for 1 minute after the audio call is ended.

New Voicemail

The handset will store up to 16 voicemails if missed callers decide to leave a message at the door

/ gate unit.

Press OK button to listen to a new voicemails.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de intercomunicación de AES

AES

AES 603 DECT Manual de usuario

AES

AES CellCOM Lite 4G Manual de usuario

AES

AES StylusAB Manual de instrucciones

AES

AES Prime 6 Series Manual de usuario

AES

AES Cellcom Prime6 Manual de usuario

AES

AES MultiCOM Classic 4G Manual de usuario

AES

AES Prime 6E Manual de usuario

AES

AES GSM-800/AB Manual de usuario

AES

AES MultiCOM Lite 4G Manual de usuario

AES

AES GSM-3AB Manual de usuario

AES

AES MultiCom 500 Manual de usuario

AES

AES 603AB Manual de usuario

AES

AES AB Manual de instrucciones

AES

AES MultiCom 500 Manual de usuario

AES

AES GSM-5AS/3GE Manual de instrucciones

AES

AES 601V Manual de usuario

AES

AES 702/AB Manual de usuario

AES

AES CellCOM Plus AB Manual de instrucciones

AES

AES 603 SPARTAN Manual de usuario

AES

AES 605A Manual de usuario

AES

AES 603AB Manual de instrucciones

AES

AES Cellcom Prime 5AB Manual de usuario

AES

AES 602AB Manual de usuario

AES

AES WiFi Predator Manual de usuario

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

CyberData

CyberData 011211 series Manual

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario