Advantech EKI-2541M/SC Manual de usuario

EKI-2541M/SC

Ethernet to Multi-mode SC

Type Fiber Optic Converter

EKI-2541S/SC

Ethernet to Single-mode SC

Type Fiber Optic Converter

User Manual

EKI-2541M & 2541S User Manual ii

The documentation and the software included with this product are copyrighted 2007 by

Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make

improvements in the products described in this manual at any time without notice. No part of

this manual may be reproduced, copied, translated or transmitted in any form or by any

means without the prior written permission of Advantech Co., Ltd. Information provided in this

manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no

responsibility for its use, nor for any infringements of the rights of third parties, which may

result from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

1st Edition

April 2007

Part No.

Printed in China

iii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be free from

defects in materials and workmanship for two years from the date of purchase.

This warranty does not apply to any products which have been repaired or altered by persons

other than repair personnel authorized by Advantech, or which have been subject to misuse,

abuse, accident or improper installation. Advantech assumes no liability under the terms of

this warranty as a consequence of such events.

Because of Advantech′s high quality-control standards and rigorous testing, most of our

customers never need to use our repair service. If an Advantech product is defective, it will be

repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you

will be billed according to the cost of replacement materials, service time and freight. Please

consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU speed,

Advantech products used, other hardware and software used, etc.) Note anything

abnormal and list any onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your manual, product, and any

helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandize

authorization) number from your dealer. This allows us to process your return more

quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement Order

Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable

container. A product returned without proof of the purchase date is not eligible for

warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid to your

dealer.

EKI-2541M & 2541S User Manual iv

Declaration of Conformity

This product has passed the CE test for environmental specifications. Test conditions for

passing included the equipment being operated within an industrial enclosure. In order to

protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage,

we strongly recommend the use of CE-compliant industrial enclosure products.

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Technical Support and Assistance

Step 1. Visit the Advantech web site at www.advantech.com/support where you can find

the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech’s customer service

center for technical support if you need additional assistance. Please have the

following information ready before you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, application software,

etc.)

- A complete description of the problem

- The exact wording of any error messages

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not

use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equipment and

must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may

cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment from

overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the equipment to

the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything over the

power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid

damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by

qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according to the user's

manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE

TEMPERATURE MAY GO BELOW -40℃(-40℉) OR ABOVE 85℃(185 ℉). THIS

COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A

CONTROLLED ENVIRONMENT.

EKI-2541M & 2541S User Manual vi

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from damage.

1. To avoid electrical shock, always disconnect the power from your PC chassis before you

work on it. Don't touch any components on the CPU card or other cards while the PC is

on.

2. Disconnect power before making any configuration changes. The sudden rush of power

as you connect a jumper or install a card may damage sensitive electronic components.

vii Contents

Contents

Chapter 1 Overview...........................................2

1.1 Introduction ......................................................... 2

1.1.1 Fast Fiber Converters Module ................... 2

1.1.2 Dual Power Input ....................................... 2

1.1.3 Flexible Mounting ...................................... 2

1.1.4 Advanced Protection ................................. 2

1.1.5 Wide Operating Temperature .................... 2

1.1.6 Easy Troubleshooting................................ 2

1.2 Features.............................................................. 3

1.3 Specification ....................................................... 4

1.4 Packing List ........................................................ 6

1.5 Safety Precaution ............................................... 6

Chapter 2 Installation........................................8

2.1 LED Indicators .................................................... 8

Table 2.1: EKI-2541M/S LED Definition.....................8

2.2 DIP-Switch .......................................................... 9

Table 2.2: EKI-2541M/S DIP-Switch Definition..........9

2.3 Dimensions (units: mm) .................................... 10

Figure 2.1: Front View of EKI-2541M/S ....................10

Figure 2.2: Side View of EKI-2541M/S......................11

Figure 2.3: Rear View of EKI-2541M/S .....................12

Figure 2.4: Top View of EKI-2541M/S ......................13

2.4 Mounting ........................................................... 14

2.4.1 Wall mounting.......................................... 14

Figure 2.5: Combine the Metal Mounting Kit.............14

2.4.2 DIN-rail Mounting..................................... 15

Figure 2.6: Installation to DIN-rail Step 1...................15

Figure 2.7: Installation to DIN-rail Step 2...................16

2.5 Network Connection ......................................... 17

2.6 Power Connection ............................................ 17

Figure 2.8: Pin Assignment of the Power Connector ..17

Chapter 3 Troubleshooting ............................20

Appendix A Pin Assignment & Wiring ...........22

Figure A.1: RJ-45 Pin Assignment..............................22

Figure A.2: EIA/TIA-568B .........................................22

Figure A.3: EIA/TIA-568A .........................................22

EKI-2541M & 2541S User Manual viii

1 Chapter1

Overview

Sections include:

zIntroduction

zFeatures

zSpecifications

zPacking List

zSafety Precaution

CHAPTER

EKI-2541M & 2541S User Manual 2

Chapter 1 Overview

1.1 Introduction

The EKI-2541M/2541S is a cost-effective solution for the converting between

10/100Base-TX and 100Base-FX cabling, it allows you to extend the cabling distance

of your 100Base-FX network up to 2 kilometers for multi-mode fiber or 30 kilometers

for single-mode fiber. The Fast Fiber Converter module gives you the option to choose

from the most popular fiber cabling connectors: SC multi-mode and single-mode

connector.

1.1.1 Fast Fiber Converters Module

The EKI-2541M/2541S provides you with one Fiber connector for your fiber optic cable

and one Ethernet RJ-45 port (Auto MDI/MDIX) for your 100Base-TX copper cable

connection. There are four DIP-switches to set the operation mode for UTP, Fiber ports

and Link Fault Pass-Through function.

1.1.2 Dual Power Input

EKI-2541M/2541S redundant power input design is with power reserve protection to

prevent the switch device broken by wrong power wiring. When one of power input is

fail, P-Fail LED will turn on and send an alarm through a relay output for notifying user.

1.1.3 Flexible Mounting

EKI-2541M/2541S is extremely compact (37 x 140 x 95 mm) and can be mounted on a

DIN-rail or a panel, so it is suitable for any space-constrained environment.

1.1.4 Advanced Protection

EKI-2541M/2541S supports up to 3,000 VDC surge protection for power line, and also

supports 4000V ESD for Ethernet ports. With these 2 strong protections, it can secure

equipment against unregulated voltage and make systems safer and more reliable.

Further, EKI-2541M/2541S provides currency overload protection with a resettable

fuse to ensure that the device component won’t be damaged by overload current.

1.1.5 Wide Operating Temperature

The operating temperature of the EKI-2541M/2541S is between -40 ~ 75 ℃(wide

operating temperature model) or -10 ~ 60 ℃(standard model). With such a wide range,

you can use the EKI-2541M/2541S in some of the harshest industrial environments

that exist.

1.1.6 Easy Troubleshooting

LED indicators make troubleshooting quick and easy. The 10/100 Base-TX port has 2

LEDs that display the link status, transmission speed and collision status. Also the

three power indicators P1, P2 and P-Fail help you diagnose immediately.

Otros manuales para EKI-2541M/SC

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Advantech

Advantech

Advantech USB-4600 Series Manual de usuario

Advantech

Advantech ADAM-6542 Manual de usuario

Advantech

Advantech EKI-2741FI Manual de usuario

Advantech

Advantech BB-USO9ML2-A Manual de usuario

Advantech

Advantech B+B SmartWorx 422CFCR Manual de usuario

Advantech

Advantech ADAM-4561-CE Manual de usuario

Advantech

Advantech B+B SmartWorx IE-ModeConverter Manual de usuario

Advantech

Advantech EKI-2741F Manual de usuario

Advantech

Advantech B+B SmartWorx 485DRCI-PH Manual de usuario

Advantech

Advantech ADAM-4561 Manual de usuario

Advantech

Advantech B+B SmartWorx Giga-MiniMc TX-SX Manual de usuario

Advantech

Advantech DVP-7020 Manual de usuario

Advantech

Advantech IE-Giga-MiniMc Manual de usuario

Advantech

Advantech PCIE-1884 Manual de usuario

Advantech

Advantech ADAM-4541 Manual de usuario

Advantech

Advantech B+B SmartWorx IMcV-10G Manual de usuario

Advantech

Advantech PCI-1784U Manual de usuario

Advantech

Advantech B+B SmartWorx Giga-MiniMc 856-10730-TX Manual de usuario

Advantech

Advantech USB-4604B Manual de usuario

Advantech

Advantech VEGA-2002 Manual de usuario

Advantech

Advantech BB-SCP211-DFTB3 Manual de usuario

Advantech

Advantech EKI-2541S/SC Manual de usuario

Advantech

Advantech EKI-2541M/SC Manual de usuario

Advantech

Advantech B+B SmartWorx 232USB9M Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario