Advantech USB-4604B Manual de usuario

USB-4604BM

12 ~ 48V

4 - port RS-232/422/485 Serial to USB Converter

TxRx TxRx

Tx RxTx Rx

User Manual USB-4600 Series

4-port RS-232/422/485 Serial to USB

Converter

Content

Chapter 1 Introduction

1.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.3. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.3.1 General......................................................................................1

1.3.2 Power Requirement...................................................................2

1.3.3 Special Communications ...........................................................2

1.3.4 Mechanism ................................................................................2

1.3.5 Software.....................................................................................3

1.3.6 Environment...............................................................................3

1.3.7 Regulatory Approvals.................................................................3

1.4. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2 Installation

2.1. Driver Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1.1 Steps for Driver Setup................................................................6

2.2. Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3. Verifying Driver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.4. Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.5. Unplugging the Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.6. Updating the Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.7. Uninstalling the Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Chapter 3 Settings

3.1. Serial Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.2. Changing the Port Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 4 Signal Connection

4.1. Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.2. LED Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

iii

Federal Communication Commission Interference

Statement

For further certification information, please go to www.advantech.com

Declaration of Conformity

The device has been tested and found to comply with the stated standard(s), which is(are)

required by the Council Directive of 2004/108/EC* and 2014/30/EU.

FCC

The device has been tested and found to comply with the stated standard(s), which is(are)

required by the Federal Communications Commission.

Product Warranty (5 years)

Advantech warrants to you, the original purchaser, that each of its products will be free from

defects in materials and workmanship for five years from the date of purchase.

This warranty does not apply to any products which have been repaired or altered by per-

sons other than repair personnel authorized by Advantech, or which have been subject to

misuse, abuse, accident or improper installation. Advantech assumes no liability under the

terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of our

customers never need to use our repair service. If an Advantech product is defective, it will

be repaired or replaced at no charge during the warranty period. For out of-warranty repairs,

you will be billed according to the cost of replacement materials, service time and freight.

Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU speed,

Advantech products used, other hardware and software used, etc.) Note anything

abnormal and list any on screen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your manual, product, and any

helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandize authori-

zation) number from your dealer. This allows us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement Order

Card and a photocopy proof of purchase date (such as your sales receipt) in a shippa-

ble container. A product returned without proof of the purchase date is not eligible for

warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid to your

dealer.

Conventions

reproduced, adapted, stored in a retrieval system, translated into any language, or transmit-

ted in any form or by any means without the written permission of the manufacturer.

Warning signs are used to identify immediate hazards for property damage, injury

or death.

CAUTION SIGNS ARE USED WARN AGAINST POTENTIAL HAZARDS OR TO CAUTION AGAINST

UNSAFE PRACTICES.

Note signs are used to provide additional information for the device or settings.

Customer Support

Technical Support and Assistance

1. Visit the Advantech web site at www.advantech.com/support where you can find the lat-

est information about the product.

2. Contact your distributor, sales representative, or Advantech's customer service center

for technical support if you need additional assistance. Please have the following infor-

mation ready before you call:

Product name and serial number

Description of your peripheral attachments

Description of your software (operating system, version, application software, etc.)

A complete description of the problem

The exact wording of any error messages

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do

not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equipment and

must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall

may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment from over-

heating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the equipment

to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything over the

power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid

damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only

by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service person-

nel:

15. The power cord or plug is damaged.

16. Liquid has penetrated into the equipment.

17. The equipment has been exposed to moisture.

18. The equipment does not work well, or you cannot get it to work according to the user's

manual.

19. The equipment has been dropped and damaged.

20. The equipment has obvious signs of breakage.

21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE

TEMPERATURE MAY GO BELOW -20°C (-4°F) OR ABOVE 60°C (140° F). THIS

COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CON-

TROLLED ENVIRONMENT.

22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY

THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANU-

FACTURER'S INSTRUCTIONS.

vii

23. The sound pressure level at the operator's position according to IEC 704-1:1982 is no

more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims

all responsibility for the accuracy of any statements contained herein.

Chapter 1

Introduction

INTRODUCTION

1.1. Overview

Advantech’s USB-4600 series of serial to USB converters are the easies, the most reliable

way to add serial ports to a PC. To attach the USB-4604B/4604BM to a PC, you don’t need

to open the chassis or power down your PC. After installing the driver, connect the USB con-

verters to your computer, will instantly get extra high-speed RS-232/422/485 ports. By sim-

ply plugging in a USB-hub, USB-4600 series eliminate the configuration issues associated

with high-priced, elder card solutions. You only have to install the driver, no need to set

cards slot, IRQ addresses, or device addresses. This reduces programming effort.

USB-4600 series products are compliant with USB 2.0 specifications, and up to 480M bps

high-speed requirement. USB-4600 series supports for transmission speeds up to 921.6k

bps, which meets the demand for high speed data exchange.

1.2. Features

USB-4600 series products have the following features:

Full compliance with USB V2.0 specifications.

RS-232/422/485 port supported

Serial Transmission speed up to 921.6 kbps

Automatic RS-485 data flow control

No external power supply necessary; the hub derives its power from USB port

Plug & Play installation

No additional IRQs or I/O ports required

Hot swap function supported

1.3. Specifications

1.3.1 General

Table 1-1. General

Specificaiton Description

Certifications CE, FCC (Class A)

Connectors 1 x USB Type B (Type A to Type B cable provided)

4 x DB9

Enclosure ABS + PC

USB Cable Max. 15ft (4.6 m)

INTRODUCTION

1.3.2 Power Requirement

1.3.3 Special Communications

1.3.4 Mechanism

Table 1-2. Power Requirement

Specificaiton Description

Power Input 12 to 48 VDC (external) or 5 VDC (Bus powered)

Power Consumption 130 mA @ 5 V (Typical)

200 mA @ 5 V (Max.)

Table 1-3. Special Communications

Specificaiton Description

Port Type RS-232/422/485, software selectable

No. of Ports 4

Port Connector DB9 male

Data Bits 5, 6, 7, 8

Stop Bits 1, 1.5, 2

Parity None, Odd, Even, Space, Mark

Transmission Speed Up to 921.6 kbps

Flow Control XON/XOFF, RTS/CTS

Baud Rate 50 bps ~ 921.6 kbps, any baud rate setting

Serial Signals RS-232: TxD, RxD, CTS, RTS, DTR, DSR, DC, RI, GND

RS-422: TxD+, TxD-, RxD+, RxD-, GND

RS-485: Data+, Data-, GND

Protection 15 KV ESD for all signals

Table 1-4. Mechanism

Specificaiton Description

Dimensions (W x D x H) 132 x 80 x 32 mm

5.2 x 3.15 x 1.26 inch

Enclosure ABS + PC

Mounting DIN-rail, panel

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Advantech

Advantech

Advantech BB-485LDRC9 Manual de usuario

Advantech

Advantech B+B SmartWorx IE-ModeConverter Manual de usuario

Advantech

Advantech ADAM-6542 Manual de usuario

Advantech

Advantech EKI-2741FI Manual de usuario

Advantech

Advantech SSPBM-K125-BTE Manual de usuario

Advantech

Advantech BB-USO9ML2-A Manual de usuario

Advantech

Advantech IE-Giga-MiniMc Manual de usuario

Advantech

Advantech VEGA-2002-3GS Manual de usuario

Advantech

Advantech BB-USOPTL4DR-2 Manual de usuario

Advantech

Advantech EKI-2541S/SC Manual de usuario

Advantech

Advantech B+B SmartWorx USOPTL4-2P Manual de usuario

Advantech

Advantech SSPB-K40-CSE Manual de usuario

Advantech

Advantech B+B SmartWorx 485USBTB-2W Manual de usuario

Advantech

Advantech B+B SmartWorx IMcV-10G Manual de usuario

Advantech

Advantech ADAM-4561 Manual de usuario

Advantech

Advantech B+B SmartWorx MiniMc TP-TX/FX Manual de usuario

Advantech

Advantech PCL-833 Manual de usuario

Advantech

Advantech USB-4600 Series Manual de usuario

Advantech

Advantech B+B SmartWorx PoE Giga-McBasic Manual de usuario

Advantech

Advantech DVP-7020 Manual de usuario

Advantech

Advantech PCIE-1182 Manual de instalación y operación

Advantech

Advantech BB-422PP9TB Manual de usuario

Advantech

Advantech EKI-2541M/SC Manual de usuario

Advantech

Advantech IMC-574I-SFP Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario