Advantech HPC-7282 Manual de usuario

User Manual

HPC-7282

2U Rackmount Chassis for a

Micro/ATX Server Board with

8 Hot Swappable Drive Bays and

7 Low Profile Expansion Slots

HPC-7282 User Manual ii

The documentation and software included with this product are copyrighted by

Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. also reserves the

right to improve the products described in this manual at any time without notice. No

part of this manual may be reproduced, copied, translated, or transmitted in any form

or by any means without the prior written permission of Advantech Co., Ltd. The

information provided in this manual is intended to be accurate and reliable. However,

Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements

on the rights of third parties that may result from its use.

Acknowledgements

HPC-7282 is a trademark of Advantech Co., Ltd.

All other product names or trademarks are properties of their respective owners.

Online Technical Support

For technical support and services, please visit our support website at

http://www.advantech.com/support

Product Warranty (2 years)

Advantech warrants the original purchaser that each of its products will be free from

defects in materials and workmanship for two years from the date of purchase.

This warranty does not apply to any products that have been repaired or altered by

persons other than repair personnel authorized by Advantech, or products that have

been subject to misuse, abuse, accident, or improper installation. Advantech

assumes no liability under the terms of this warranty as a consequence of such

events.

Because of Advantech’s high quality-control standards and rigorous testing, most

customers never need to use our repair service. If an Advantech product is defective,

it will be repaired or replaced at no charge during the warranty period. For out-of-war-

ranty repairs, customers are billed according to the cost of replacement materials,

service time, and freight. Please consult your dealer for more details.

If you think you have a defective product, follow the steps outlined below.

1. Collect all information about the problem encountered (for example, CPU

speed, Advantech products used, other hardware and software used, etc.). Note

anything abnormal and list any onscreen messages received when the problem

occurs.

2. Call your dealer and describe the problem. Please have your manual, product,

and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an return merchandise authori-

zation (RMA) number from your dealer. This allows us to process your return

more quickly.

4. Carefully pack the defective product, a completed Repair and Replacement

Order Card, and proof of the purchase date (such as a photocopy of your sales

receipt) in a shippable container. Products returned without a proof of purchase

date are not eligible for warranty service.

5. Write the RMA number clearly on the outside of the package and ship it prepaid

to your dealer.

Part No. 2001728200 Edition 1

Printed in Taiwan November 2015

iii HPC-7282 User Manual

Safety Instructions

1. Read these safety instructions carefully.

2. Retain this user manual for future reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use only a damp

cloth for cleaning. Do not use liquid or spray detergents.

4. For pluggable equipment, the power outlet socket must be located near the

equipment and easily accessible.

5. Protect this equipment from humidity.

6. Place this equipment on a reliable surface during installation. Dropping or letting

the equipment fall may cause damage.

7. Do not leave this equipment in an unconditioned environment where the room

temperature fluctuates below 0 °C (32°F) or above 40 °C (104°F). This may

damage the equipment.

8. The openings on the enclosure are for air convection. Protect the equipment

from overheating. Do not cover the openings.

9. Ensure the power source voltage is correct before connecting the equipment to

a power outlet.

10. Position the power cord away from high traffic areas. Do not place anything over

the power cord.

11. All cautions and warnings on the equipment should be noted.

12. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage by transient overvoltage.

13. Never pour liquids into an opening. This may cause fire or electrical shock.

14. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

15. If one of the following occurs, have the equipment checked by service person-

nel:

The power cord or plug is damaged.

Liquid has penetrated the equipment.

The equipment has been exposed to moisture.

The equipment is malfunctioning or does not operate according to the user

manual.

The equipment has been dropped and damaged.

The equipment has obvious signs of breakage.

16. The computer is equipped with a battery-powered real-time clock circuit. Batter-

ies are at risk of exploding if incorrectly replaced. Replace only with the same or

equivalent type recommended by the manufacturer. Discard used batteries

according to the manufacturer’s instructions.

17. The CD drives provided with the computer are compliant with relevant safety

standards, including IEC 60825.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

18. This device complies with Part 15 of the FCC Regulations. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference

that may cause undesired operation.

19. Always completely disconnect the power cord from the chassis before manually

handling the hardware. Do not make connections while the power is on. Sudden

power surges can damage sensitive electronic components.

HPC-7282 User Manual iv

20. Always ground yourself to remove any static charge before touching the mother-

board, backplane, or add-on cards. Contemporary electronic devices are very

sensitive to static electric charges. As a safety precaution, wear a grounding

wrist strap at all times. Place all electronic components on a static dissipative

surface or in a static-shielded bag when not in the chassis.

21. Any unverified component may cause unexpected damage. To ensure correct

installation, always use the components (screws) provided in the accessory box.

A Message to the Customer

Advantech Customer Services

Every Advantech product is built to the most exact specifications to ensure reliable

performance in the harsh and demanding conditions typical of industrial environ-

ments. Whether your new Advantech product is destined for a laboratory or factory

floor, be assured that your product will deliver the reliability and ease of operation for

which Advantech is renowned. Your satisfaction is our primary concern. This section

will provide a guide to Advantech's customer services. To ensure you receive the full

benefit of our services, please carefully follow the instructions below.

Technical Support

We want all customers to get the best performance possible from our products.

Should you experience technical difficulties, we are available to help. Answers to the

most frequently asked questions can be easily found in the product documentation.

Because these answers are normally a lot more detailed than those provided over

the phone, we recommend consulting this manual first. If you are still unable to find a

solution, gather all information or questions that apply to your problem, and with the

product in hand, call your dealer. Our dealers are well trained and ready to provide

the support you need to get the most from your Advantech products. Generally, most

of the problems reported are minor and can be easily solved over the phone.

Additionally, Advantech engineers are available to provide free technical support

every business day. We are always ready and willing to give advice about application

requirements or specific information regarding the installation and operation of any of

our products.

v HPC-7282 User Manual

Initial Inspection

Before system installation, please ensure that the following items have been included

in your shipment:

Chassis

–1 x HPC-7282 chassis

Components

–3 x 80*25 mm 4-pin PWM fan

–8 x HDD tray

–1 x SAS/SATA hard drive backplane

Accessories

–1 x accessory box with a package of screws

–2 x HDD tray key

If any of these items are missing or damaged, contact your distributor or sales repre-

sentative immediately. The HPC-7282 has been mechanically and electrically

inspected before shipment. Thus, the system should be free from blemishes and

scratches and in perfect working order upon receipt. While unpacking, double check

the system for signs of shipping damage (for example, a damaged box, scratches,

dents, etc.). If the system is damaged or fails to meet the specifications, notify our

service department or your local sales representative immediately. Additionally,

please notify the carrier. Retain the shipping carton and packing material for inspec-

tion by the carrier. After inspection, we will make arrangements to repair or replace

the unit.

HPC-7282 User Manual vi

vii HPC-7282 User Manual

Contents

Chapter 1 General Information ............................1

1.1 Introduction ............................................................................................... 2

1.2 Specifications ............................................................................................ 2

1.3 Environmental Specifications .................................................................... 2

Table 1.1: Environmental Specifications ..................................... 2

1.4 Dimensions Diagram................................................................................. 3

Figure 1.1 Dimensions Diagram .................................................. 3

Chapter 2 System Setup.......................................5

2.1 Overview ................................................................................................... 6

2.2 Removing the Chassis Cover.................................................................... 6

2.2.1 Disconnecting the Chassis from the Power Source...................... 6

2.2.2 Removing the Chassis Cover ....................................................... 6

Figure 2.1 Top Cover Removal.................................................... 6

Figure 2.2 Top Cover Reattachment ........................................... 7

2.3 Removing and Replacing the System Fans .............................................. 7

2.3.1 Fan Installation.............................................................................. 7

Figure 2.3 Fan Removal and Installation ..................................... 7

2.4 Installing a Motherboard............................................................................ 8

Figure 2.4 Motherboard Installation ............................................. 8

2.5 Installing a Power Supply Unit .................................................................. 9

Figure 2.5 Single Power Supply Unit Installation......................... 9

Figure 2.6 2U Redundant Power Supply Unit Installation............ 9

Chapter 3 Operation............................................11

3.1 Overview ................................................................................................. 12

Figure 3.1 Chassis User Interface ............................................. 12

3.2 Control Panel Buttons ............................................................................. 12

3.3 Control Panel LEDs................................................................................. 13

3.4 Front Control Board................................................................................. 14

Chapter 4 2U 8-Bay SAS Backplane..................15

4.1 HDD Backplane Top View....................................................................... 16

Table 4.1: Rear SAS/SATA Connectors.................................... 16

Table 4.2: Rear LED Indicators ................................................. 16

4.1.1 HDD Backplane (Mini-SAS) Top View (optional) ........................ 17

Table 4.3: Rear SAS/SATA Connectors.................................... 17

Table 4.4: Rear LED Indicators ................................................. 17

4.2 HDD Backplane Rear View ..................................................................... 18

4.2.1 HDD Backplane (Mini-SAS) Rear View (optional) ...................... 18

4.3 Rear Connector and Pin Definitions........................................................ 19

4.3.1 Backplane Main Power Connectors............................................ 19

Table 4.5: Backplane Main Power 4-Pin Connector.................. 19

4.3.2 Fan Connectors .......................................................................... 19

Table 4.6: 3-Pin Fan Connectors............................................... 19

4.3.3 Redundant Power Supply Fail Alarm Connector ........................ 19

Table 4.7: Redundant Power Supply 2-Pin Connector.............. 19

4.3.4 SATA Ports ................................................................................. 19

HPC-7282 User Manual viii

Chapter 1

1General Information

HPC-7282 User Manual 2

1.1 Introduction

HPC-7282 is a 2U rackmount industrial computer chassis for high-performance and

high-capacity computing applications. The equipment meets a variety of application

requirements for filing, printing, e-mail, and web access. This powerful computing

platform is suitable for mission-critical computer telephony applications, industrial

automation, and factory management. A wide range of standard computing peripher-

als can be integrated with the chassis to satisfy the demands of various applications

and need for 24/7 operation under harsh conditions.

1.2 Specifications

Construction: Heavy-duty steel

Disk Drive Capacity: One slim ODD bay

Front Panel LED Indicators: Power, HDD activity, LAN status, and system

information

Front Panel Switch and Button: Power switch, system reset button

Front Panel I/O Interfaces: Two USB2.0 ports, one COM port

Cooling System: Three 80 x 25 mm hot swappable cooling fans

Weight: 15 kg

Dimensions (W x H x D): 437 x 88 x 533.4 mm

1.3 Environmental Specifications

Table 1.1: Environmental Specifications

Environment Operating Non-Operating

Temperature 0 °C ~ 40 °C -40 °C ~ 70 °C

Humidity 10 ~ 85% @ 40 °C non-condensing 10 ~ 95% @ 40 °C non-condensing

Tabla de contenidos

Otros manuales de Hardware de computadora de Advantech

Advantech

Advantech ASMB-815 Series Manual de usuario

Advantech

Advantech PCLD-8811 Manual de instalación y operación

Advantech

Advantech PCIE-1841 Manual de usuario

Advantech

Advantech SOM-5883 Manual de usuario

Advantech

Advantech ASMB-830 Series Manual de usuario

Advantech

Advantech PCA-6011 Manual de instalación y operación

Advantech

Advantech PCL-818L Manual de usuario

Advantech

Advantech Watchdog Timer UNO-2171 Manual de usuario

Advantech

Advantech SKY-MXM-A1000 Manual de usuario

Advantech

Advantech RSB-4221 Manual de usuario

Advantech

Advantech SOM-7583 Manual de usuario

Advantech

Advantech FWA-3700 Manual de usuario

Advantech

Advantech AIMB-786 Manual de instalación y operación

Advantech

Advantech PCA-6753 Manual de instalación y operación

Advantech

Advantech PCA-6114P7 Manual de instalación y operación

Advantech

Advantech MIO-2263 Manual de instalación y operación

Advantech

Advantech EPD-660 Manual de usuario

Advantech

Advantech FWA-3033-00A1R Manual de instalación y operación

Advantech

Advantech AIMC-3202 Manual de instalación y operación

Advantech

Advantech PCA-6011 Manual de instalación y operación

Advantech

Advantech EPD-332 Manual de usuario

Advantech

Advantech MIC-300 Manual de instalación y operación

Advantech

Advantech ASMB-831 Series Manual de instalación y operación

Advantech

Advantech PCE-3029 Manual de instalación y operación

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario