ADEMCO VISTA Manual de usuario

4120EC

SECURITY SYSTEM

USER’S MANUAL

N4861V4 9/92

TABLE OF CONTENTS

lNTRoDucTloN ..................................................................................3

FIRE AND BURGLARY PROTECTION .....................................................4

ENTRY/EXITDELAYS ............................................ .............................. .

SECURllY CODES .............................................................................5

DURESS CODE ...................................................................................5

FUNCTIONSOFTHECONSOLE ............................................................. 6

DlsmMING mEsYswM ANDslLENclNG AMRMs ................................8

cHIMEmE .....................................................................................8

CHECKING FOROPEN ZONES ................................................ .............. 9

Bypassing PRoEcTloN zoNEs ........................<...............................9

ARMINGPERIMEIERONLY(STAY/lNSTANT) .........................................10

ARMINGALLPROTECTION (AWAYMIMXIMUM) .......................................11

PANlc KEYs .....................................................................................l2

TESTINGTHESYSTEM .......................................................................13

mouBLEmNDmloNs ......................................................................l4

FIRE ALARM SYSTEM .........................................................................l5

NATIONAL FIRE PROTECTION ASSN. RECOMMENDATIONS .....................16

Emergency Evacuation ................................................................l7

SUMMARY OF AUDIBLE NOTIFICATIONS ...............................................l8

PRoEcTDN zoNEs LlsT ..................................................................l9

QUICK GUIDE TO SYSTEM Functions .................................................l9

EMERGENCYPHONENUMBERS ..........................................................2O

OWNER’SINSURANCE PREMIUMCREDIT REQUESTFORM ......................21

GLOSS~Y ......................................................................................23

FCCSTATEMENT ...............................................................................25w

~ELIMITATONS OF WISAMRM SYSEM ..........................................26

-2-

INTRODUCTION

Congratulations on your ownership of aVISTA Security System. You’ve made a

wise decision in choosing it, for it represents the latest in security protection

~chnology today.

Basically, this system offers you

three forms of protection: burglary,

fire and emergency. To realize the

system’s full potential, it is important

that you feel comfortable in operating

it. Your system consists of at least

one Console which provides full

control of system operation, various

sensors which provide perimeter and

interior burglary protection, plus a

selected number of strategically

placed smoke or combustion

detectors designed to provide early

warning in case of fire.

The system uses microcomputer

technology to monitor all protection

zones and system status and

provides appropriate information for

display on the Console(s) used with

the system, and initiates appropriate

alarms. When programmed to do so,

the system can also transmit

appropriate alarm or status messages

over the phone lines to acentral alarm

monitoring station.

ItiEr=T

@aEiibiEq EI1313

W,..s m,, 9,?.ss

Eimm

.,.. Cc.x m

Immm

Eimm

L.. J

4127 4137

THE DISPLAY CONSOLES feature amultifunction, 12-key digital keypad,

and uses afixed-word English language/zone numeric LCD display which

displays the nature and location of all occurrences. The consoles also have a

built-in sounder. There are two fixed word consoles available. The 4137 features

backlit keys, while the 4127 features acompact design (its keys are not backlit).

–3-

FIRE &BURGLARY PROTECTiON

One or more sensing devices will have

been assigned by the installer of your

alarm system to each of the various

protection zones in your system

(although not every zone may have

been used). For example, the sensing

device on your Entry/Exit door may

have been assigned to zone 01,

sensing devices on windows in the

master bedroom to zone 02, and so on.

These numbers will appear on the

display when the respective zone is

faulted.

The fire protection portion of your

security system (if used) is always on

and will sound an alarm if afire

condition is detected. Refer to the

FIRE ALARM SYSTEM section for

important information concerning fire

protection, smoke detectors and

planning emergency exit routes from

your house.

ENTRY/EXIT DELAYS

Your system was programmed by the

installer with apreset entry delay time,

during which the system must be

disarmed upon entering or an alarm will

occur. This feature allows you to

reenter through the entry delay door

without setting off the alarm. Aslow

beeping will sound at the console to

remind you to disarm the system. The

entry delay feature can also be turned

off for greater security when sleeping

or while away for extended periods of

time (INSTANT &MAXIMUM modes).

Apreset exit delay was also

programmed to allow you time to leave

the premises without setting off the

alarm after arming the system. See

your installer for your delay times.

The burglary protection portion of your

system must be armed before it will

sense burglary alarm condition

When an alarm occurs, both th~

console and external sounders will

sound, and a message in the Display

Window will identify the zone(s)

causing the alarm. In addition, if your

system is connected to acentral

monitoring station, an alarm report will

be sent. Disarming the system will

stop alarm sounding. Your system

provides four modes of burglary

protection: STAY, AWAY INSTANT

and MAXIMUM, and even allows you

to BYPASS selected zones of

protection while leaving the rest of the

system armed. The system also

provides aCHIME mode, for alerting

users to the opening and closing of

doors and windows while the system

is disarmed. Refer to the other

sections of this manual for

procedures for using these features.

Exit Delay: oseconds

Entry Delay: oseconds

Delays may be from 15 to 225

seconds in non-UL installations, but

no more than 60 seconds for Ex

delay or 45 seconds for Entry delay-

for aUL Listed Household burglary

application.

-4–

SECURITY CODES

At the time of installation, your

installer programs apersonal four-

digit code, known only to you and

yours. This code must be entered

when performing most system

functions, including arming and

disarming of the system. As an

additional safety feature, up to 6

temporary codes can be assigned for

use by those not having a need to

know the master code. Temporary

codes are assigned single-digit “User

numbers” from 3to 8. Before

assigning atemporary code though,

be sure it does not conflict with the

DURESS code (see DURESS CODE

section). Note that the master code

remains in effect even when a

temporary code is assigned.

NOTE: Users to whom temporary

codes have been assigned should not

be shown how to bypass protection

points unless they have a need to

know. It is also recommended that

obvious codes such as 1111 or 1234

not be assigned.

QUICK ARMING: Note that if “Quick

Arming” was programmed by the

installer, the [#] key can be pressed in

place of the security code when

arming the system. The security code

is always required when disarming the

To Assign or deiete

TemDorarv Codes:

E;ter Ma;ter code.

Press CODE [8] key.

Enter User Number to be assigned

or deleted (3-8).

To assign acode, enter temporary

code for that User Number.

To delete acode, enter Master

Code for that User Number.

The Console will beep once when

procedure has been completed

successfully.

}/I

/ I u

coosik QLicx

AJIMXEY

(lF PROGR#MME~

DURESS CODE

(WHEN FORCED TO DLSARM/ARM UNDER THREAT)

Enter the first three digits of the

security code. Increase the final digit

by one and then press OFF (or

AWAY, etc. if arming the system).

The system will disarm (or arm), but

can silently notify the central station

of your situation, if that service has

been provided.

For example, if the Normal security

code is”1 23 4“, the Duress security

code is”1 23 5“.

IMPORTANT

●This code is useful only when

connected to acentral station.

●Duress code capability is not

present for codes ending in 9.

●Users of tempxaty codes must be

instructed to enter their codes

carefully to avoid the possibility of

accidentally entering the Duress

code.

-5-

FUNCTIONS OF THE CONSOLE

1. DISPLAY WINDOW: Refer to the

FIXED WORD DISPLAY CONSOLE

System Status Display table on the

next page for alist of messages that

might appear along with their

meanings.

2. OFF KEY: Disarms the burglary

portion of the system, silences alarms

and audible trouble indicators, and

clears visual alarm trouble after the

problem has been corrected.

3. AWAY KEY: Completely arms

both perimeter and interior burglary

protection for backup protection by

sensing an intruder’s movements

through protected interior areas as well

as guarding doors, windows, etc. Late

arrivals can enter through an entry

delay zone without causing an alarm if

the system is disarmed before the

entry delay time expires.

4. STAY KEY: Arms the perimeter

burglary protection, guarding doors,

windows and other perimeter protection

points, and sounds an alarm if one is

opened. Interior protection is not

armed, which allows movement within

your house without causing an alarm.

Late arrivals can enter through an

entry delay zone without causing an

alarm if the system is disarmed before

the entry delay time expires.

5. TEST KEY: Tests the a!arm

sounder if disarmed. Refer to the

TESTING THE SYSTEM section for

test procedures.

6. BYPASS KEY: Re meves

individual protection zones from being

monitored by the system. Displays

previously bypassed protection zones.

7. CHIME KEY: Turns on &off the

CHIME mode. When on, any entry

through adelay or perimeter zone

while the system is disarmed will

cause atone to sound at the

Console.

8. [#] KEY: Permits ARMING of the

system without use of asecurity code

(“Quick Arm”, if programmed to do sc

9. KEYS O-9: Used to enter y~

individual security access code(s).

10. CODE KEY: Allows the entry of

additional user codes that can be

given to other users of the system.

11. [*] READY KEY: When

depressed prior to arming the system,

the console will display all open

protection zones.

12. INSTANT KEY: Arms in

manner similar to STAY mode, but

turns off the entry delay period,

offering greater security while inside

and not expecting any late arrivals,

An alarm will occur immediately upon

opening any perimeter protection

point, including entry delay zones.

13. MAXIMUM KEY: Arms in

manner similar to AWAY mode, but

eliminates the entry delay period, thus

providing maximum protection. An

alarm will occur immediately upon

opening any protection point,

including entry delay zones.

14. POWER INDICATOR:

(GREEN) Lit when primary power is

on. If off, system is operating on its

backuD batterv oower. CALL YOUR

INSTALLER IMMEDIATELY.

15. ARMED INDICATOR: (RED~

Lit when the system has been armed

(STAY, AWAY, INSTANT or

MAXIMUM).

16. INTERNAL SOUNDER:

Source of audible internal warning and

confirmation sounds, as well as

alarms (see “Summary of Audible

Notifications”).

-6-

\//

\\/

I \ -. .... ..../

IIImp“”‘--”--‘‘= ‘

FIXED WORD DISPLAY CONSOLE

System Status Displays

AWAY All burglary zones, interior &perimeter, are armed.

STAY Perimeter burglaty zones, such as windows &doors, are armed.

INSTANT Perimeter burglary zones armed and entry delay is turned off.

BYPASS One or more burglary protection zones have been bypassed.

NOT READY Appears when burglary portion of the system is not ready for

arming (due to open protection zones).

READY The burglary POrtion of the system is ready

NO AC Appears when AC power has been cut off.

‘AC Appears when AC power is present.

CHIME Aooears when the CHIME

to be armed.

_feature is activated.

-ARM Appears when an intrusion has been detected and the system is

armed (also appears during aFire alarm). Accompanied by the

protection zone ID in alarm.

CHECK Appears when amalfunction is discovered in the system at any

time or if afault is detected in aFIRE zone at any time or in a

DAY~lGHT burglaty zone during adisarmed period.

Accompanied by adisplay of zone number in trouble.

FIRE Appears when afire alarm is present. Accompanied by adisplay

of the zone in alarm.

IMPORTANT!: When using the keypad to enter

codes and commands, sequential key depressions

must be made within 3seconds of one another If 3

seconds elapses without akey depression, the entry

is abortad and must be re eated from its binnin .

-7-

DISARMING THE SYSTEM

AND SILENCING ALARMS

(FOFi AWAY, STAY, INSTANT, AND MAXIMUM ARMING)

PROCEDURE RESULT

Enter security code and press Any alarm sounders will be silence

OFF [1]. The READY message ALARM and zone number (~

will be displayed and the console displayed) will clear only when the

will beep once to confirm that the open sensor is closed.

system is disarmed, unless an Afire alarm is indicated by adisplay of

alarm has occurred. both FIRE and the zone number on

If an alarm has occurred, note the the Console. These will clear only

zone number displayed and repeat when the fire zone is again intact. -

step 1to restore the READY

message display. If the message See “SUMMARY OF AUDIBLE

NOTIFICATION” section for

will not display, go tot he displayed

protection zone and remedy the information which will enable you to

fault (close windows, etc.). If the distinguish between FIRE and

fault cannot be remedied, notify BURGIARY alarm sounds.

the alarm agency. ~~ ENTER

CHIME MODE

(THIS FEATURE IS FUNCTIONAL ONLY WHEN THE SYSTEM IS

Your system can be set to alert you to To turn Chime Mode

the opening of adoor or window while the security code and

it is disarmed by using CHIME mode. CHIME [9] key. The

When activated, three tones will message will appear.

PRESS

OFF

DISARMED)

on, enter

press the

CHIM L

sound at the Console whenever adoor To turn Chime Mode off, enter

or window is opened, and the Not

Ready message will be displayed. the security code and press the

Pressing the READY [*] key will CHIME [9] key again. The CHIME

display the open zone number. Note message will disappear.

that Chime mode can be activated

only when the system is Disarmed.

-8-

cd la&lei

fiiaixl

rala~ ENTER

m0-” ●’-- qm> -- ‘CODE &

PRESS

CHIME

CHECKING FOR OPEN ZONES

BEFORE ARMING YOUR SYSTEM, ALL PROTECTED DOORS,

WINDOWS AND OTHER PROTECTION ZONES MUST BE CLOSED.

PROCEDURE

lftheNOT READY messageis

displayed priorto arming, check

for open zones by depressing

and releasing the READY [*]

key (do not enter code first).

All open protection points will be

displayed. These” pints must

be either closed or bypassed

before the system can be

armed. The READY message

will be displayed when all

protection zones have been

either closed or bypassed.

BYPASSING PROTECTION ZONES

(FOR ARMING WITH ONE OR MORE ZONES SELECTIVELY UNPROTECTED)

PROCEDURE

System must be disarmed first.

Enter security code.

Press BYPASS [6] and enter zone

number(s) of zones to be bypassed

(e.g., 01, 02, 03, etc.).

Important! All single-digit zone

numbers must be preceded by a

zero (example, enter 01 for zone 1).

When finished entering all zone

numbers to be bypassed, wait for

bypassed zones to be sequentially

displayed before arming.

The BYPASS message will be

displayed indicating the presence

of one or more bypassed zones.

Arm the system as usual.

Bypassed zones are unprotected

and will not cause an alarm when

violated while system is armed.

NOTES:

1. All bypasses are removed when an

OFF sequence (security code plus

OFF) is performed.

2. Temporary users should not be

shown how to bypass protection

points unless they have a need to

know.

DISPLAYING BYPASSED ZONES

(For determining what zones have

been previously bypassed)

1. Enter security code and press

BYPASS [6].

2. Wait for all bypassed zones to be

sequentially displayed.

LIMITATIONS

●Fire or emergency zones cannot

be bypassed.

●Arming the system before

bypassed zones are displayed

nullifies all bypasses.

–-@

Elicata

U●-●-. qi_rmg

-9-

ARMING PERIMETER ONLY

STAY: STAYING HOME, EXPECTING LATE ARRIVALS

INSTANT: STAYING HOME, NO LATE ARRIVALS EXPECTED

PROCEDURE

1. Enter the security code when the 3. The armed state message will ~

READY message is displayed. displayed, accompanied by three

2. Press the STAY [3] or INSTANT beeps from the Console. Exit delay

[71key, depending on arming mode begins. Perimeter protection is in

desired. effect immediately, except entry

delay zone if STAY key is

pressed.

STAY KEY RESULT

Arms sensors guarding doors and

windows, with entry delay on. Late

arrivals can enter through the entry

delay zone door and disarm the

system within the entry delay period

without causing an alarm. See your

installer for actual delay times set for

your system. Alarms will occur

instantly when any exterior protection

point is violated, except the entry

delay zone door, which will activate an

alarm if the system is not disarmed

within the entry delay period. Interior

protection points are disarmed to

permit freedom of movement

throughout the interior.

–lo-

INSTANT KEY RESULT

Arms sensors guarding doors a-

windows, with entry delay off. Alarms

will occur instantly when any exterior

protection point is violated, including

the entry delay zone door. Interior

protection points are disarmed to

permit freedom of movement

throughout the interior.

Otros manuales para VISTA

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de seguridad de ADEMCO

ADEMCO

ADEMCO VISTA-20SE Manual del propietario

ADEMCO

ADEMCO Vista-128BP Instrucciones de funcionamiento

ADEMCO

ADEMCO 4140XMPT2 Manual de usuario

ADEMCO

ADEMCO Vista-10 Manual de usuario

ADEMCO

ADEMCO LYNXR24 Manual de usuario

ADEMCO

ADEMCO 4110DLa Manual de usuario

ADEMCO

ADEMCO LYNXR Manual del propietario

ADEMCO

ADEMCO VISTA-20P Series Instrucciones de funcionamiento

ADEMCO

ADEMCO Security System VISTA-15 Instrucciones de montaje

ADEMCO

ADEMCO VISTA-120 Manual de usuario

ADEMCO

ADEMCO Vista-20HW Manual de usuario

ADEMCO

ADEMCO Vista-10P Instrucciones de montaje

ADEMCO

ADEMCO Security Center 4160 Manual de usuario

ADEMCO

ADEMCO 4110 Manual de usuario

ADEMCO

ADEMCO Vista 4140XMPT Manual de usuario

ADEMCO

ADEMCO Security System VISTA-15 Manual de usuario

ADEMCO

ADEMCO 4140XMP Manual de usuario

ADEMCO

ADEMCO 4110DL Manual de usuario

ADEMCO

ADEMCO Vector Manual de usuario

ADEMCO

ADEMCO LYNXR Manual de usuario

ADEMCO

ADEMCO Security System VISTA-10SE Instrucciones de funcionamiento

ADEMCO

ADEMCO VISTA-120 Instrucciones de montaje

ADEMCO

ADEMCO 4140 Manual de usuario

ADEMCO

ADEMCO Vista-128B PLUS Instrucciones de montaje

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario