ADA INSTRUMENTS DigiTeo-2 Manual de usuario

Operating manual

Electronic theodolite

Model: DigiTeo-2/5/10/20

Manufacturer Address: WWW. ADAINSTRUMENTS.COM

DigiTeo-2/5/10/20

Table of contents

1. Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. Construction features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Display and display mark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5. Operating keyboard and operating key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

6. Preparative before measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

7. The use of the laser plummet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

8. Power switch on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

9. Change the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

10. Angle measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

11. Output the data and serial communication (DigiTeo-2; 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

12. Memory mode (DigiTeo-2; 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

13. Function setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

14. Setting the vertical collimation error and the telescope axis error and the compensator error . . . . . . . . . . . . . . . . . . . . 16

15. The other function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

16. Check and adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

17. Error display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

18. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

19. Accessories and equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

20. Container contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

21. Warranty/Exceptions from responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

22. Appendix 1- “Certicate of acceptance and sale”

23. Appendix 2- “Warranty card”

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

General

Thank you for selecting the DigiTeo Electronic Theodolite of ADA Instruments. For the best performance of the instrument, please

read this operator’s manual carefully and keep it in a convenient location for future reference.

Precautions

1. Avoid heavy shock

For long-distance transportation, pay attention to external package and shock proof.

2. Setting and moving

When placing the instrument on the tripod head, hold the instrument and rotate the tripod screw until it is xed securely on top of the

tripod head. Repeat the above mentioned procedure for removing the instrument from tripod head. If the instrument must be carried

with tripod attached, never carry it horizontally over the shoulder, always keep it in vertical direction when carried. The instrument

must be kept in container for long-distance transportation.

3. Keep it clean

Clean dust of the instrument surface with cotton wool or small brush after using the instrument. Dry the instrument on time after

exposed in the rain. Make sure not to use chemicals to clean battery case and plastic parts. If necessary, damp soft cloth is permissible.

High absorbent cotton and lens-cleaning paper are used for exposed optics. Never use handkerchief and clothes.

4. Avoid the long-time irradiation

Never leave the instrument in extreme heat longer than necessary. It could adversely affect its performance.

5. Check the batterie

Be sure to check the battery for voltage level before using the instrument.

6. Notice

Store of the instrument should have good air circulation and low humidity. Temperature is kept under 45ºC. Often change drier in

the instrument container.

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

Application

DigiTeo electronic theodolite adopts incremental digit angle measurement system. The resolution of horizontal angle reading and verti-

cal angle reading is 1″, 5″(0.2mgon, 1mgon ). The angle precision is 2″, 5″(0.5mgon, 1mgon ).

Meanwhile microcomputer techniques adopted in the instrument realizes automatic calculation, storage, and display. The instrument

can display the readings of horizontal angle and vertical angle simultaneously. It can use with the PDA and EDM . Then you can get the

electric speed measurement instrument. It can display, put down the angle, distance and coordinate data. It can correct the instrument

error. Many measuring modes as angle, slope etc can be fullled. DigiTeo electronic theodolite is used for the control surveying, mine,

railway, and irrigation etc projects surveys. Still capable of topographic surveys and general projects surveys.

Construction features

Objective lens

Sighting collimator

Vertical tangent screw and motion clamp

Late level

Display windows

Battery

Operating key

Base

Circular level

Handle screw

Carrying handle

Focusing knob

Eyepiece

Horizontal x clamp and motion clamp

RS-232C communication interface

Base locking lever

Foot screw

10.

11.

12.

13.

14.

15.

16.

17.

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

Pic.1

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

Display and display mark

Display Function Display Function

SD Slope distance HOLD Hold the horizontal angle

HD Level distance TILT Over the compensation range

VD Height distance Battery level

VA Vertical angle % Percent grade

HALHorizontal angle left m Distance unit, #m

HARHorizontal angle right gon Angle unit

SFT The second function 08-06-09 Date

REP Repeat the horizontal angle 14:38 Time

CRN Compensate Auto power off

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

Operating keyboard and operating key

Keys Function 1 Function 2

OSET Setting horizontal 0 Distance measurement

(Connected with rangender)

HOLD Hold the horizontal angle Repeat horizontal angle

measurement

SFT Illuminate Select the second

function

R/L Horizontal angle right or left Setting the mode

V% Percent grade of vertical

angle

Output the data

Power switch

Preparative before measurement

1. Level the instrument.

1.1. Level and center the instrument correctly to insure

the best performance.

1.2. Place the tripod.

First, put the tripod leg in the proper position and

tighten the locking screws.

1.3. Leveling the instrument with circular level.

Use leveling screws 1,2 to move the bubble of the

circular level until the bubble of the circular level

until the bubble is now located on a line perpendicu-

lar to a line running through the centers of the two

leveling screws being adjusted. Revolve the level-

ing screw 3 to shift the bubble to the center of the

circular.

bubble bubble

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

1.4.1. Loosen horizontal motion clamp and revolve

the instrument. By adjusting leveling screws 1,2 , the

plate level vial is parallel to a line running through the

centers of two leveling screws, and place the bubble

in the center of the level vial.

1.4.2. Next, revolve the instrument 90° (100gon)

around its vertical axis and use the remaining screw

3 to center the level bubble once more.

1.4.3. Repeat the above procedure for each 90°

(100gon) revolution of the instrument and check

whether the level bubble is correctly centered for

all points.

2. Centering the instrument with laser plummet

Turn on the laser plummet by pressing and holding down the SFT for

2 seconds. Move the tool by loosening the screws on the tripod. Align

the point of the laser plummet with the required point on the terrain

(object).

3. Final levelling of the instrument

Repeat procedure of (1) and check whether the level bubble is in the

center of the level vial. Finally tighter adjusting screw.

1.4. Further leveling the instrument with plate level

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

Power switch on

Press , all segments of the display will light on. The

display shows that Vertical angle should be zero. Rotate

the telescope to set the instrument to a vertical angle read-

ing of 0. Press over 2 seconds, it can be power off.

● In order to make sure instrument work continuously,

pay attention to battery display. If battery is insufcient,

replace battery.

● For setting the vertical angle at 0, a datum 0 is provided

on the vertical angle scale circumference. If the telescope

is turned and the sensor passes the datum 0, angle mea-

surement begins.

Power display

Sufcient battery power

Effective battery power

Need to replace battery

Measurement is impossible. The power will

be cut off in one minute.

Change the batteries

For removing: Push the two locking levers to the op-

posite direction and pull out the battery box . Then take

the battery from the box.

Angle measurement

1. Measuring a HAR and vertical angle

Operating Display

Collimate the rst target.

Press [OSET] twice and make

the target horizontal angle A is

0°00′00″.

Collimate the second target B

and the horizontal and vertical

angles are displayed.

How to collimate

- Point the telescope towards the light. Turn the diopter ring and adjust

the diopter so that the cross-hair is clearly observed. (Turn the ring

coward you rst and then backward to focus.)

Installation: First Put the battery into the battery box , then Push the two

locking levers to the opposite direction and put the battery box to the

instrument until it clicks into the position.

MEASUREMENT FOUNDATION

DigiTeo-2/5/10/20

- Observe the target with sighting collimator. Allow a

certain space between the collimator and yourself, if for

collimating.

- Focus the target with the focusing knob (pic.2).

Note:

If the focus of the telescope is incorrect the parallax is

created between the cross-hair and target when viewing

vertically or horizontally. This will affect precision in

measurement or survey. The parallax should be elimi-

nated by carefully focusing.

Pic.2

2. Alternation of HARand horizontal angle left HAL

Conrm in the angle mode

Operating Display

Collimate the target A.

Press [L/R], and it will

change between the HAR

and HAL.

Measure in the HL mode.

● Press [L/R] key, HAR/ HALis alternation. Every time press

the key, HALand HARmode can alternate.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de ADA INSTRUMENTS

ADA INSTRUMENTS

ADA INSTRUMENTS ZCM 130 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS Schmidt Hammer 225 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS WHEEL 100M Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS PRODIGIT MARKER Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS LASERMARKER 70 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS COSMO 70eter Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ZFM 100 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ARMO MINI Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ROBOT-40 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS Cosmo 70 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ROTARY 500 HV SERVO Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS AngleMeter 30 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ZHT 125 Electronic Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS COSMO MINI Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ZSM 330 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ZHM 125B Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS AngleRuler Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS Vertical Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS 3D Liner 2V Green Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ZHT 60 Manual de usuario

ADA INSTRUMENTS

ADA INSTRUMENTS ProDigit MICRO Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario