Abit WI-1P Manual de usuario
WI-1P
Intel Pentium 4 Workstation Board
Socket 478
User’s Manual
4200-0391-01
Rev. 1.00
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
WI-1P
Table Of Contents
Chapter 1. Introduction .................................................... 1-1
1.1. Specifications ......................................................................... 1-1
1.2. Layout..................................................................................... 1-3
1.3. Jumpers & Connectors Description........................................ 1-4
Chapter 2. Hardware Setup.............................................. 2-1
2.1. Install Pentium®4 CPU and Heatsink Supporting-Base........ 2-1
2.2. System Memory ..................................................................... 2-3
2.2.1. Memory Configuration Table...................................2-3
2.2.2. Installing and Removing Memory Modules.............2-3
2.3. Connectors, Headers, and Switches .......................................2-5
2.3.1. ATX Power Connectors............................................ 2-5
2.3.2. FAN Power Connectors............................................2-6
2.3.3. CMOS Memory Clearing Header............................. 2-7
2.3.4. PS/2 & USB Device Wake-up Connection Header.. 2-8
2.3.5. Front Panel Switches & Indicators Connection
Headers ..................................................................... 2-9
2.3.6. Front Panel Audio Connection Header................... 2-10
2.3.7. Internal Audio Sources Connectors........................ 2-11
2.3.8. PCI Slots ................................................................. 2-12
2.3.9. Additional IEEE1394 Port Connection Header...... 2-13
2.3.10. Additional USB Port Connection Header............... 2-14
2.3.11. System Management Bus Connection Header ....... 2-15
2.3.12. Infrared Device Connection Header ....................... 2-16
2.3.13. Chassis Intrusion Device Header............................ 2-17
2.3.14. AGP Pro Display Card Slot .................................... 2-18
2.3.15. Additional COM2 Port Connection Header ........... 2-19
2.3.16. Floppy and IDE Disk Drive Connectors................. 2-20
2.3.17. Serial ATA Connectors........................................... 2-21
2.3.18. Status Indicators...................................................... 2-23
2.3.19. External I/O Panel Connectors ...............................2-24
User’s Manual
Chapter 3. BIOS Setup...................................................... 3-1
3.1. SoftMenu Setup ...................................................................... 3-2
3.2. Standard CMOS Features.......................................................3-5
3.3. Advanced BIOS Features ....................................................... 3-9
3.4. Advanced Chipset Features.................................................. 3-12
3.5. Integrated Peripherals........................................................... 3-15
3.6. Power Management Setup.................................................... 3-23
3.7. PnP/PCI Configurations ....................................................... 3-27
3.8. PC Health Status................................................................... 3-30
3.9. Load Fail-Safe Defaults........................................................ 3-32
3.10. Load Optimized Defaults ..................................................... 3-32
3.11. Set Password......................................................................... 3-32
3.12. Save & Exit Setup ................................................................ 3-32
3.13. Exit Without Saving ............................................................. 3-32
Chapter 4. Driver Installation .......................................... 4-1
Appendix A. How to Get Technical Support ..................... A-1
WI-1P
Introduction 1-1
Chapter 1. Introduction
1.1. Specifications
CPU
• Supports Intel Pentium 4 Northwood/ Prescott Socket 478 processors
with 800/533MHz FSB
• Up to 3.06GHz and higher (Prescott supports 3.4GHz and higher)
• Supports Intel Hyper-Threading Technology
Chipset
• Intel 875P/ ICH-Hance Rapid
• Supports Dual Channel DDR 400/333 with ECC function and Turbo
mode
• Supports Advanced Configuration and Power Interface (ACPI)
Memory
• Four 184-pin DIMM sockets
• Supports 144-bit wide Dual Channel DDR 400/333 memory
• Up to 4GB, un-buffered with ECC/ Non-ECC memory capacity
Graphics
• Accelerated Graphics Port slot supports AGP 8X/4X (0.8V/1.5V)
Serial ATA
• 2 channel Serial ATA 150MB/s data transfer rate via Intel Hance
Rapid
• 4 channel Serial ATA 150MB/s data transfer rate via Silicon Image
3114 (Option)
Audio
• 6-Channel AC97 CODEC on board
System BIOS
• Supports ABIT SoftMenu
• Supports Plug-and-Play (PNP)
• Supports Advanced Configuration Power Interface (ACPI)
• Write-Protect Anti-Virus function by AWARD BIOS
• 4MB Flash ROM
User’s Manual
1-2 Chapter 1
LAN
• Intel 82547GI single port Gigabit Ethernet Controller
• Front panel LAN Active/Link LED
Extension Slot
• 1x AGP
• 1x PCI 32bit/33MHz (5V)
• 3x PCI-X 64bit/66MHz (3.3V)
Internal I/O Connectors
• 1x Floppy Port supports up to 2.88MB
• 2x Ultra ATA 100/66/33 connectors
• 1x COM port header (COM2)
• 6x Serial ATA 150 connectors
• 1x USB 2.0 header (Each header supports two USB 2.0 devices)
• 1x SM Bus header (For SM Bus and I2C)
• 1x CD-IN, 1x AUX-IN connector
• 1x IEEE1394 header
• 1x IrDA header
External I/O Connectors
• 1x PS/2 keyboard, 1x PS/2 mouse port
• 1x printer port
• 1x COM port
• 1x S/PDIF in
• 1x S/PDIF out
• 1x audio connector (Lin-out, Line-in, Mic)
• 1x audio connector (Surround-out, Center/Subwoofer)
• 2x USB 2.0, 1x RJ-45 w/Transformer LAN Connector
• 1x IEEE 1394 connector
Miscellaneous
• ATX form factor (305mm x 243mm)
• Hardware monitoring – Including Fan speeds, Voltages, System
environment temperature
• Chassis intrusion detector header
Specifications and information contained herein are subject to change
without notice.
WI-1P
Introduction 1-3
1.2. Layout
User’s Manual
1-4 Chapter 1
1.3. Jumpers & Connectors Description
Jumpers Description Default Setting
CCMOS1 CMOS Memory Clearing Header Pins 1-2 Closed (Normal)
JP1 Chassis Intrusion Device Header Opened
Connectors Description
AGP1 AGP Pro Display Card Slot
ATXPWR1/ATX12V1 ATX Power Connectors
CPUFAN1
NBFAN1
SYSFAN1
AUXFAN1/AUXFAN2
CPU Fan Power Connector
Chipset Fan Power Connector
System Fan Power Connector
Auxiliary Fan Power Connectors
CD1/AUX1 Internal Audio Sources Connectors
COM2 Additional COM2 Port Connection Header
DIMM 1~4 DDR DIMM Slots
FDC1 Floppy Disk Drive Connector
FP-1394-1 Additional IEEE1394 Port Connection Header
FP-AUDIO1 Front Panel Audio Connection Header
FPIO1 Front Panel Switches & Indicators Connection Headers
FPIO2 Infrared Device Connection Header
FP-USB1 Additional USB Port Connection Header
IDE1/IDE2 Hard Disk Drive Connectors
PCI1 32bit/33MHz PCI Slot
PCI2/PCI3/PCI4 64bit/66MHz PCI-X Slots
PS2-PWR1
USB-PWR1 PS/2 & USB Device Wake-up Connection Header
SATA1~SATA6 Serial ATA Connectors
SMB1 System Management Bus Connection Header
WI-1P
Hardware Setup 2-1
Chapter 2. Hardware Setup
2.1. Install Pentium®4 CPU and Heatsink Supporting-Base
This motherboard provides a ZIF
(Zero Insertion Force) Socket 478
to install Intel®Pentium®4 CPU.
The CPU you bought should have a
kit of heatsink and cooling fan along
with. If that’s not the case, buy one
specially designed for Pentium®4
Socket 478.
1. Locate the 478-pin ZIF socket
on the motherboard. Fasten the
Retention Module Base onto the
motherboard.
ATTENTION: If you are using
chassis specially designed for
Pentium®4, please pay attention to
the location of metal studs or
spacers if they are already installed
on the chassis. Be careful not let the
metal studs or spacers contact the
printed circuit wire or parts on the
PCB.
2. Pull the CPU socket lever
sideways away from the socket
and then upwards to 90 degree.
Insert the CPU with the correct
orientation. Do not use extra
force to insert CPU; it only fits
in one orientation. Close down
the socket lever while holding
down the CPU.
3. Put the heatsink faces down
onto the CPU until it completely
covers the CPU.
User’s Manual
2-2 Chapter 2
4. Put the Fan and Retention Mechanism Assembly onto the heatsink. Make sure all
the four Retention Locks at each side of the Fan and Retention Mechanism
Assembly snap into the Retention Holes.
5. Push down the Retention Lock at both sides of the Fan and Retention Mechanism
Assembly to lock up together with the Retention Module Base.
6. The Fan and Retention Mechanism Assembly and Retention Module Base should
now firmly lock up with each other with the heatsink inside.
ATTENTION: Do not forget to set the correct bus frequency and multiple for your
processor.
WI-1P
Tabla de contenidos
Otros manuales de Hardware de computadora de Abit
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
