Abit AV8 Manual de usuario
AV8
AMD Athlon 64™ (FX) System Board
Socket 939
User’s Manual
4200-0400-01
Rev. 1.00
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are the
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
If you do not properly set the motherboard settings, causing the motherboard to
malfunction or fail, we cannot guarantee any responsibility.
AV8
Table Of Contents
Chapter 1. Introduction .......................................................................... 1-1
1-1. Features & Specifications ........................................................................1-1
1-2. Layout Diagram .......................................................................................1-3
Chapter 2. Hardware Setup.................................................................... 2-1
2-1. Install The Motherboard...........................................................................2-1
2-2. Install CPU and Heatsink.........................................................................2-2
2-3. Install System Memory ............................................................................2-3
2-4. Connectors, Headers and Switches ..........................................................2-5
(1). ATX Power Input Connectors........................................................2-5
(2). FAN Connectors.............................................................................2-6
(3). CMOS Memory Clearing Header ..................................................2-7
(4). Wake-up Header.............................................................................2-8
(5). Front Panel Switches & Indicators Headers ..................................2-9
(6). Additional USB Port Headers......................................................2-10
(7). Additional IEEE1394 Port Headers .............................................2-11
(8). Front Panel Audio Connection Header ........................................2-12
(9). Internal Audio Connectors ...........................................................2-13
(10). GURU Clock Connection Header................................................2-13
(11). Accelerated Graphics Port Slot....................................................2-14
(12). Floppy Disk Drive Connector......................................................2-15
(13). IDE Connectors............................................................................2-16
(14). POST Code Display .....................................................................2-17
(15). Serial ATA Connectors .................................................................2-18
(16). Status Indicators...........................................................................2-19
(17). Back Panel Connectors ................................................................2-20
Chapter 3. BIOS Setup............................................................................ 3-1
3-1. µGuru Utility............................................................................................3-3
3-2. Standard CMOS Features.........................................................................3-9
3-3. Advanced BIOS Features.......................................................................3-12
3-4. Advanced Chipset Features....................................................................3-14
3-5. Integrated Peripherals ............................................................................3-18
3-6. Power Management Setup .....................................................................3-21
3-7. PnP/PCI Configurations.........................................................................3-24
3-8. Load Fail-Safe Defaults .........................................................................3-26
User’s Manual
3-9. Load Optimized Defaults .......................................................................3-26
3-10. Set Password ..........................................................................................3-26
3-11. Save & Exit Setup ..................................................................................3-26
3-12. Exit Without Saving...............................................................................3-26
Appendix A. Install VIA 4-in-1 Driver ................................................................. A-1
Appendix B. Install Audio Driver ......................................................................... B-1
Appendix C. Install LAN Driver ........................................................................... C-1
Appendix D. Install VIA USB 2.0 Driver .............................................................D-1
Appendix E. Install VIA Serial ATA RAID Driver.............................................. E-1
Appendix F. Install ABIT µGuru Driver.............................................................. F-1
Appendix G. POST Code Definition .....................................................................G-1
Appendix H. Troubleshooting (Need Assistance?)...............................................H-1
Appendix I. How to Get Technical Support ......................................................... I-1
AV8
Introduction 1-1
Chapter 1. Introduction
1-1. Features & Specifications
1. CPU
• Supports AMD AthlonTM 64 / AthlonTM 64 FX 939-pin processor
• 2000MHz system bus using HyperTransportTM technology
2. CPU Integrated Dual Channel Memory Controller
• Four 184-pin DIMM sockets (Un-buffered, Non-ECC DIMM)
• Supports 2 DIMM Single Channel DDR 400/333/266 (Max. 2GB)
• Supports 4 DIMM Dual Channel DDR 400/333/266 (Max. 4GB)
3. Chipset
• VIA K8T800 Pro + VT8237
• Supports Advanced Configuration and Power Management Interface (ACPI)
• Accelerated Graphics Port connector supports AGP 8X/4X
4. SATA 150 RAID
• Supports SATA 150 MB/s RAID 0/1
5. Gigabit LAN
• On board Gigabit PCI Ethernet Controller
• Operation support ACPI & Wake on LAN
6. IEEE 1394
• Supports 3 ports IEEE 1394 at 100/200/400 Mb/s transfer rate
7. Audio
• On board 6-Channel AC 97 CODEC
• Professional digital audio interface supports optical S/PDIF Input/Output
8. ABIT Engineered
• ABIT µGuruTM Technology
• ABIT CPU ThermalGuardTM Technology
9. Internal I/O Connectors
• 1x AGP 8X/4X slot
• 5x PCI slots
• 1x floppy port supports up to 2.88MB
• 2x Ultra DMA 33/66/100/133 connectors
• 2x SATA 150 connectors
User’s Manual
1-2 Chapter 1
• 2x USB headers
• 2x IEEE 1394 headers
• 1x FP-Audio header
• 1x CD-IN, 1x AUX-IN header
10. Back Panel I/O
• 1x PS/2 keyboard, 1x PS/2 mouse
• 1x Serial port connector, 1x Parallel port connector
• 1x S/PDIF In connector
• 1x S/PDIF Out connector
• 1x AUDIO1 connector (Rear-Left / Rear-Right, Center/Subwoofer)
• 1x AUDIO2 connector (Mic-In, Line-In, , Front-Left/Front-Right)
• 2x USB, 1x IEEE 1394 Connector
• 2x USB, 1x RJ-45 LAN Connector
11. Miscellaneous
• ATX form factor: 305 x 245 mm
Specifications and information contained herein are subject to change without notice.
AV8
Introduction 1-3
1-2. Layout Diagram
User’s Manual
1-4 Chapter 1
AV8
Hardware Setup 2-1
Chapter 2. Hardware Setup
Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow motherboard to be securely
attached on and at the same time, prevented from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use with studs
2. or use with spacers
In principle, the best way to attach the board is to
use with studs. Only if you are unable to do this
should you attach the board with spacers. Line up
the holes on the board with the mounting holes on
the chassis. If the holes line up and there are
screw holes, you can attach the board with studs.
If the holes line up and there are only slots, you
can only attach with spacers. Take the tip of the
spacers and insert them into the slots. After doing
this to all the slots, you can slide the board into
position aligned with slots. After the board has been positioned, check to make sure everything is OK
before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
User’s Manual
2-2 Chapter 2
2-2. Install CPU and Heatsink
This motherboard provides a ZIF (Zero Insertion
Force) Socket 939 to install AMD Socket 939
CPU. The CPU you bought should contain with a
kit of heatsink, cooling fan, retention frame and
blackplate. If that’s not the case, buy one specially
designed for Socket 939.
Please refer to the figure shown here to install
CPU and heatsink. (For reference only. Your
Heatsink & Fan Assembly may not be exactly the
same as this one.)
1. Locate the Socket 939 on this motherboard.
Pull the CPU release lever sideways to
unlatch and then raise it all the way up.
2. Drop the processor with its pin side down into
the CPU socket. Do not use extra force to
insert CPU; it only fits in one direction. Close
the CPU release lever.
3. Align the Backplate Standoffs with the
mounting holes on motherboard. Position the
backplate onto motherboard.
4. Place the Retention Frame onto the
motherboard and align it with the Backplate
Standoffs.
5. Place heatsink on top of CPU, and make sure
the heatsink fits properly on the retention
frame.
6. Hook both sides of the Spring Clip onto the
Mounting Tabs of Retention Frame. Tighten
screws until the Spring Clip is fully installed.
7. Attach the fan connector of Heatsink & Fan
Assembly with the CPU-FAN connector on
the motherboard.
ATTENTION: Do not forget to set the correct
bus frequency and multiple for your processor.
AV8
Tabla de contenidos
Otros manuales de Hardware de computadora de Abit
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
