Abicor Binzel SI4 Series Manual de usuario

TECHNOLOGY FOR THE WELDER’S WORLD.

www.binzel-abicor.com

ABICOR BINZEL Corporation

650 Medimmune Court, Suite 110

Frederick, MD 21703

Phone: (301) 846-4196

Fax: (301) 846-4497

ABIROB W Liner Instructions

SI4-XXX Series Liners

LINCOLN DIRECT TORCHES

1. Position the torch cable as straight as possible.

2. With the torch neck and consumables ﬁtted, insert the liner into the rear of the torch until it bottoms in the tip

holder/tip or wire-brake if ﬁtted.

3. At the rear end of the torch measure the distance from the feeder plug to the end of the liner collet (Fig. 1). This is

dimension “X”.

4. Remove the liner from the torch and remove the dimension “X” from the front end of the liner (Fig. 2).

5. At the rear end of the liner, you must trim the excess liner which protrudes from the liner collet. Measure 4mm

past the collet and cut the excess oﬀ (Fig. 3). Note: When cut properly the liner should be ﬂush to 1mm recessed in

the liner nut.

6. Apply O-ring grease. Install the liner into the torch and tighten the liner retention nut (Fig. 4).

Fig. 1

Fig. 2

Fig. 3

Fig. 4

liner liner collet

4mm

liner retention nut

cut

Feeder plug

(Miller Direct Torches

on back...)

TECHNOLOGY FOR THE WELDER’S WORLD.

www.binzel-abicor.com

ABICOR BINZEL Corporation

650 Medimmune Court, Suite 110

Frederick, MD 21703

Phone: (301) 846-4196

Fax: (301) 846-4497

ABIROB W Liner Instructions

SI4-XXX Series Liners

MILLER DIRECT TORCHES

1. Position the torch cable as straight as possible.

2. With the torch neck and consumables ﬁtted, insert the liner into the rear of the torch until it bottoms in the tip

holder/tip or wire-brake if ﬁtted.

3. At the rear end of the torch measure the distance from the feeder plug to the end of the liner collet (Fig. 1) and

subtract 5mm. This is dimension “X”.

4. Remove the liner from the torch and remove the dimension “X” from the front end of the liner (Fig. 2).

5. At the rear end of the liner, you must trim the excess liner which protrudes from the liner collet. Measure 7mm

past the collet and cut the excess oﬀ (Fig. 3). Note: When cut properly the liner should protrude from the liner collet

by approximately 2mm or two coils.

6. Apply O-ring grease. Install the liner into the torch and tighten the liner retention nut (Fig. 4).

Fig. 1

Fig. 2

Fig. 3

Fig. 4

liner liner collet

7mm

liner retention nut

cut

2mm

(L - 5mm = X)

Feeder plug

(Lincoln Direct Torches

on back...)

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de soldadura de Abicor Binzel

Abicor Binzel

Abicor Binzel MIG Manual de usuario

Abicor Binzel

Abicor Binzel ABIPLAS 71 HF Manual de usuario

Abicor Binzel

Abicor Binzel iROB 401 AC/DC Manual de usuario

Abicor Binzel

Abicor Binzel MT 452 W Manual de usuario

Abicor Binzel

Abicor Binzel FreedomDrive Abimig AT355 Manual de usuario

Abicor Binzel

Abicor Binzel ABIMIG GRIP W Series Manual de usuario

Abicor Binzel

Abicor Binzel ABICAR 1200 PRO Manual de usuario

Abicor Binzel

Abicor Binzel iROB 420 Manual de usuario

Abicor Binzel

Abicor Binzel ABIROB A Series Manual de usuario

Abicor Binzel

Abicor Binzel xFUME FLEX 115V CSA Manual de usuario

Abicor Binzel

Abicor Binzel ALPHA FLUX 350 Manual de usuario

Abicor Binzel

Abicor Binzel MIG/MAG ROBO Series Manual de usuario

Abicor Binzel

Abicor Binzel PP Plus Series Manual de usuario

Abicor Binzel

Abicor Binzel ABIPLAS CUT 200 W/MT Manual de usuario

Abicor Binzel

Abicor Binzel ABIMIG A155 Manual de usuario

Abicor Binzel

Abicor Binzel TIG ABITIG MT Manual de usuario

Abicor Binzel

Abicor Binzel SR/ABITIGL ABITIG GRIP Manual de usuario

Abicor Binzel

Abicor Binzel iMIG POWER 400 Manual de usuario

Abicor Binzel

Abicor Binzel ROBO WH W600 Manual de usuario

Abicor Binzel

Abicor Binzel ABI-CAR E-1200 Manual de usuario

Abicor Binzel

Abicor Binzel ABICAR ADVANCED 42V Manual de usuario

Abicor Binzel

Abicor Binzel AUT-WIG 20G Manual de usuario

Abicor Binzel

Abicor Binzel ABICAR 1200 PRO Manual de usuario

Abicor Binzel

Abicor Binzel ABITIG GRIP 150 2 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario