ABB STT04 Manual de usuario

INSTRUCTION MANUAL

Smart Transmitter Terminal

STT04

PN25054

Trademarks and Registrations

Registrations and trademarks used in this document include:

® Windows Registered trademark of Microsoft Corporation

® Windows NT Registered trademark of Microsoft Corporation

® Lexan Registered trademark of General Electric Company, GE Plastics Division

WARNING notices as used in this manual apply to hazards or unsafe practices which could result in personal

injury or death.

CAUTION notices apply to hazards or unsafe practices which could result in property damage.

NOTES highlight procedures and contain information which assist the operator in understanding the informa-

tion contained in this manual.

All software, including design, appearance, algorithms and source codes, is copyrighted by ABB Inc. and is

owned by ABB Inc. or its suppliers.

WARNING

POSSIBLE PROCESS UPSETS. Maintenance must be performed only by qualified personnel and only after

securing equipment controlled by this product. Adjusting or removing this product while it is in the system may

upset the process being controlled. Some process upsets may cause injury or damage.

NOTICE

The information contained in this document is subject to change without notice.

ABB Inc., its affiliates, employees, and agents, and the authors of and contributors to this publication specifi-

cally disclaim all liabilities and warranties, express and implied (including warranties of merchantability and fit-

ness for a particular purpose), for the accuracy, currency, completeness, and/or reliability of the information

contained herein and/or for the fitness for any particular use and/or for the performance of any material and/or

equipment selected in whole or part with the user of/or in reliance upon information contained herein. Selection

of materials and/or equipment is at the sole risk of the user of this publication.

This document contains proprietary information of ABB Inc., and is issued in strict confidence. Its use, or repro-

duction for use, for the reverse engineering, development or manufacture of hardware or software described

herein is prohibited. No part of this document may be photocopied or reproduced without the prior written con-

sent of ABB Inc..

ABB Instrumentation

ADDENDUM

INTRODUCTION

This addendum supplements information contained in the WPBEEUI110502B0 STT04 Product Instruction. The

purpose of this addendum is to "map" or corellate function ke

s on the revised STT04EBO ke

pad to the original

STT04 ke

pad function ke

s that are documented in the Product Instruction. This addendum also provides

supplemental 600TEN Transmitter information which is not contained in the existin

STT04 Product Instruction.

Refer to the STT04 Product Instruction for specific operatin

details.

OPERATOR/INTERFACE CONTROLS

The illustrations below show the comparison between the old and new STT04 ke

pads:

Old Keypad New Keypad

STT04EB_

Smart Transmitter Terminal

PN24969

ADDENDUM

Table 1 provides a comparison of old-ke

pad vs. new-ke

pad functions for the ke

s on the STT04 terminal.

NOTE: The configure, view, select device and options keys function without a field device connected to the

STT04 terminal. The other functions are locked out until a field device is connected to the terminal.

Table 1. Keypad Functions

Old Key New Key Function

Powers the unit up and displa

s the STT04 firmware revision level.

Turns power off. Stored confi

urations remain in internal memor

. The termi-

nal will shut itself off after 15 minutes of idle operation.

Scrolls throu

h menus and selects functions.

Inputs values into the terminal. Includes di

its 0 throu

h 9, ASCII characters A

throu

h Z, si

ns, and punctuation.

Completes an input or a selection.

1. Inputs a new confi

uration into the STT04 internal memor

2. Modifies an existin

confi

uration.

3. Erases an existin

confi

uration from the terminal memor

Retrieves, views and optionall

saves the confi

uration of the selected field

device.

Sends a confi

uration from the STT04 terminal to a selected field device.

Steps throu

h various calibration procedures

(

dependenton the selected field

device

)

Monitors primar

input or output, secondar

output, ambient temperature of

the selected field device, and other variables.

OFF

+ : / < > *

% & G H I

ENTER

CONFIG

GET

CONFIG

SEND

CONFIG

CALI-

BRATE

MONITOR

ADDENDUM

Displa

s field device status based on results of continuous self-dia

nostics.

1. Chan

es en

ineerin

units.

2. Sets lower and upper ran

e values of primar

and secondar

units.

3. Chan

es the output dampenin

1. Sets output to a fixed value.

2. Cancels a fixed output.

3. Sets up LCD - select displa

units to be displa

ed on the field device LCD.

4. Chan

es device confi

uration to the standard confi

uration

(

PTS onl

NOTE: For special feature functions for the Type AVS Smart Positioner, refer

to Appendix A.

Escapes the current function and returns the displa

to the

READY

condition.

Selects and chan

es workin

confi

urations and field devices

(

if connected

)

Steps throu

h the selections of the workin

confi

uration. Views a confi

ura-

tion, but does not allow modifications to be made.

1. Sets the lan

e of the displa

screens.

2. Sets the communication format.

3. Displa

s the amount of char

e left on the batter

pack.

4. Displa

s the STT04 name.

Returns to a previous screen durin

confi

uration, calibration, reran

e, etc.

Table 1. Keypad Functions(continued)

Old Key New Key Function

STATUS

RE-

RANGE

SPECIAL

FEATURE

CLEAR

SELECT

DEVICE

VIEW

OPTIONS

BACK

ADDENDUM

APPENDIX - 600T & 600TEN PRESSURE TRANSMITTER

INTRODUCTION

This appendix covers the confi

uration and calibration functions of the T

pe 600T EN Pressure Transmitter.

Refer to SECTION 4 - OPERATING PROCEDURES for information on the followin

functions:

CREATE/MODIFY CONFIGURATION

A confi

uration can be created off-line, without a connected field device. Refer to Fi

ure 1 for an overview of the

confi

uration function. The followin

table details the confi

uration process.

• Send configurations. • Select configurations.

• Get configurations. • Erase configurations.

• View configurations. • Operational functions.

Figure 1. Configuration Flowchart (600T & 600T EN)

ADDENDUM

Key Display Comments

Select

NEW

to create a confi

uration. To modif

existin

confi

uration, select

MODIFY

. The screen

uence is the same, however, the

MODIFY

screens will appear with the values and arrow posi-

tions as the

were ori

inall

confi

ured.

Select

HART

Select

600T

Enter a name for the confi

uration ID ta

usin

up to

ht ASCII characters. To select a character, press

the ke

that has the desired character. Continue to

press the ke

until the desired character appears.

Use the ri

ht arrow ke

to move to the next charac-

ter. Use the left arrow ke

o back to the previous

character.

Select

ANALOG.

NOTE:

The DIGITAL

selection should only be made

when using an IMFBS01 field bus I/O module. A

CHANNEL #

prompt appears when

DIGITAL

selected.

CONFIG

ENTER

CONFIGURATION

→NEW

MODIFY

ERASE

ENTER

DEVICE TYPE

BAILEY FSK

→HART

[ 6 TIMES ]

ENTER

TRANSMITTER TYPE

PTH EBTH

TB82 pH TB82 ORP

TB82 pION TB82 CONC

TZID/AXH AS800

TEU211 TS11/TS01

50XE4000 50XM2000

50SM‘1000 →600T

HART UNIV

ENTER

STT04 CONFIGURATION

[

]

←PREVIOUS NEXT→

ENTER

SELECT MODE:

→ ANALOG

DIGITAL

ADDENDUM

pe a descriptive messa

e usin

up to 32 charac-

ters. This field can be used to note an

thin

of impor-

tance to the device or installation.

To select a character, press the ke

that has the

desired character. Continue to press the ke

until the

desiredcharacter appears. Use the ri

ht arrow ke

move to the next character. Use the left arrow ke

o back to the previous character.

pe a descriptor strin

usin

up to 16 characters.

This field can be used for notations about the device

or process.

To select a character, press the ke

that has the

desired character. Continue to press the ke

until the

desiredcharacter appears. Use the ri

ht arrow ke

move to the next character. Use the left arrow ke

o back to the previous character.

Enter a da

and press . Enter a month and

press . Enter a

ear and press .

This date can represent the creation date of the con-

uration, the date the device or element was

installed, or some other si

nificant date.

Select

600T EN

Select

LINEAR

NOTE: Other output t

pe selections are:

SQUARE ROOT

SQR (x^3)

SQR (x^5)

5th ORDER POLYNOMIAL

DOUBLE POLYN

Use to return to a previous confi

uration

screen from an

screen in the confi

uration process.

Enter a value between 0 and 16 seconds.

Key Display Comments

ENTER

MESSAGE:

←PREVIOUS NEXT→

ENTER

DESCRIPTOR:

←PREVIOUS NEXT→

ENTER

DATE:

DAY: nn

MONTH: nn

YEAR: nn

ENTER

CONFIG TYPE

600T

→600T EN

ENTER

OUTPUT TYPE

→LINEAR

SQU (x)

SQR (x^3)

SQR (x^5)

5th ORD. POLY

DOUBLE POLYN

BACK

ENTER

DAMPING:

(0 - 16 SEC)

0.5 SECS

ADDENDUM

Select an en

ineerin

unit best suited for the

application. Other units not shown include

mmHg-

0oC, PSI, BARS, mBAR, gSqCm, Kgcm2, PA, KPA,

torr-0oC, ATM, MPa, iH2O-4oC, mmH2O-4oC

Input lower ran

e value usin

the number ke

s, then

press . Input the upper ran

e value, then

press .

Select the 600T EN

TEMPERATURE UNITS.

Use arrow ke

to select option, then press

Select

YES

Key Display Comments

ENTER

ENGINEERING UNIT

→iH20-20c

iHg-0Oc

ftH2O-20c

mmH20-20c

ENTER

LOWER RANGE VAL

nn.nn UNITS

UPPER RANGE VAL

nn.nn UNITS

ENTER

TEMPERATURE UNITS

→ °C °F

°R °K

ENTER

STORE THIS

CONFIGURATION?

→YES

ENTER

ID TAGNAME

READY

ADDENDUM

CALIBRATION

This section details the 600T EN

SUHVVXUH

transmitter calibration functions usin

an STT04 terminal. There are four

types of calibration functions:

•Sensor Trim

•D-to-A adjust (Analog Mode only)

•PV Bias

•Set Output %

Refer to Fi

ure 2 for an overview of the calibration functions.

Figure 2. Calibration Flowchart (600T EN)

Tabla de contenidos

Otros manuales de Transmisor de ABB

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario