ABB LMT100 Manual de usuario

—

ABB MEASUREMENT & ANALYTICS | COMMISSIONING INSTRUCTIONS

LMT Series

Magnetostrictive level transmitter LMT100 & 200 models

Quick Start Guide

K-TEK Level products

Measurement made easy

LMT SERIES | MAGNETOSTRICTIVE LEVEL TRANSMITTER LMT100 & 200 MODELS | CI/LMT100/200-EN REV. B

Sales Service

Contents

1 Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3 Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LMT SERIES | MAGNETOSTRICTIVE LEVEL TRANSMITTER LMT100 & 200 MODELS | CI/LMT100/200-EN REV. B

Introduction

The LMT Series of level transmitters is a modular range of field

mounted, microprocessor-based electronic transmitters,

utilizing multiple sensor technologies. Accurate and reliable

measurement of liquid levels is provided in even the most

difficult and hazardous industrial environments. The LMT

Series can be configured to provide specific industrial output

signals, according to 4-20 mA with HART digital

communication. The LMT Series consists of two models:

LMT100 (insertion-mounted) and LMT200 (mounted on gauge

(KM26).

Standard Precautions

CAUTION

Only qualified and authorized personnel are to be tasked

with the installation, electrical connection, commissioning

and maintenance of the transmitter. Qualified personnel are

those individuals who have experience in the installation,

electrical connection, commissioning and operation of the

transmitter or similar devices and hold the necessary

qualifications. These qualifications include but not limited

to:

• Training or instruction – authorization to operate and

maintain devices or systems according to safety

engineering standards for electrical circuits, high

pressures and aggressive media

• Training or instruction in accordance with safety

engineering standards regarding maintenance and use of

adequate safety systems.

Since the transmitter may form a link within a safety chain,

it is recommended that the device be replaced immediately

if defects are detected. In the event of use in a hazardous

area, only non-sparking tools are to be used.

IMPORTANT NOTE

Read the LMT Series operating instructions carefully before

working with the product. For personal and system safety and

for optimum performance, make sure you thoroughly

understand the contents before installing, using or maintaining

this instrument.

Features

– High accuracy: 0.01% of full scale or + 1.27mm

– Never requires re-calibration: set it & forget it

– Superior Sensor (Patent #5,473,245)

– Local indication with HMI display

– Dual compartment housing with separate field terminal

compartment

– Loop powered to 22m (75ft) probe length

– Total and/or interface level measurement

– Pressure to 165.48 bar (2400 psig) Std. 124.1 bar (1800 psig)

– Temperature range: -195.5 to 426.6°C (-320 to 800°F) with

options

– Field replaceable/upgradable electronics module

– Built-in RFI / EMI filter

– Field Replaceable / Upgradable Electronics Module

– Digital Communications

– Online Self-verification

LMT SERIES | MAGNETOSTRICTIVE LEVEL TRANSMITTER LMT100 & 200 MODELS | CI/LMT100/200-EN REV. B

1 Electrical Connections

2 Mounting

1 Internal earthing

terminal

2 Power supply, current

output / HART output

3 Load resistance

4 Power supply / supply

isolator

5 PLC / DCS

6 HART Handheld terminal

7 External indicator

8 External earthing

terminal

9 Terminal for external

indicator

0 Laptop

LMT100 Transmitters installations:

A Installed in external chambers in a level and interface measurement

application

B Installed directly into vessel, measuring level and interface level

C Installed directly into vessel measuring level only

Figure 1 LMT100 Mounting

Figure 2 LMT200 Mounting

Bottom Mount

Top Mount

LMT SERIES | MAGNETOSTRICTIVE LEVEL TRANSMITTER LMT100 & 200 MODELS | CI/LMT100/200-EN REV. B

3 Easy Setup

1 Log on to the LMT at the Standard or Advanced access level.

2 Select Easy Setup in the main menu.

3 Select a language in the “Easy Setup” menu and press .

4 Select available option of primary variable in the “Easy

Setup” menu and press .

5 Select available option of units of measure in the “Easy

Setup” menu and press .

6 Set LRV in the “Easy Setup” menu and press .

LRV is the lower range value which corresponds to 4 mA current

out value.

7 Set URV in the “Easy Setup” menu and press .

URV is the upper range value which corresponds to the 20 mA

current out value.

8 Set Damping time in the “Easy Setup” menu and press .

Damping allows smoothing step response in the device output.

9 Select displayed variable in the “Easy Setup” menu and

press .

Sets the selected process variable on the first line on the

process display.

10 Set a tag in the “Easy Setup” menu and press .

A tag is a quick way to identify the device.

*For detailed commission/operation steps refer to LMT

operating instructions.

LMT SERIES | MAGNETOSTRICTIVE LEVEL TRANSMITTER LMT100 & 200 MODELS | CI/LMT100/200-EN REV. B

Specifications (Refer to LMT100/200 Datasheets for Details)

Electronic transmitter:

Repeatability ± 0.005% of Full Scale or 0.305 mm (0.012 in), whichever is greater

Non-linearity ± 0.01% of Full Scale or 0.864 mm (0.034in), whichever is greater

Measuring accuracy ± 0.01% of Full Scale or 1.27 mm (0.050 in), whichever is greater

Supply voltage 12 to 42 Vdc - 4-20mA HART loop powered

Output/Communications 4-20mA HART7®

User Interface Interactive display, DTM, EDDL with NE107 messaging

Power consumption 4-20mA at 36.0 Vdc - 3.6mA 0.13 watts; 21mA 0.76 watts

at 12.0 Vdc - 3.6mA 0.043 watts; 21mA 0.25 watts

HART mode (4.0mA) at 36.0 Vdc 0.144 watts

at 12.0 Vdc 0.048 watts

Ambient temperature -40 to 85°C (-40 to 185°F) Ambient

Humidity 0 to 100% RH

Electrical connection Two M20 x 1.5 or two 1/2in. FNPT, adapters and bus connectors also available

Ingress protection IP66, NEMA 4X

Sensor tube:

Material 316/L Stainless Steel

Process temperature LMT100: -195.5 to 121.1°C (-320 to 250°F)

Process pressure LMT100: -1.0 to 124.1 bar @ 149°C (-14.7 to 1800 psig @ 300°F)

Probe length LMT100: 304.8mm to 9.14m (1 to 30ft) / LMT200: 304.8mm to 15.24m (1 to 50ft)

Figure 3 LMT General Model

6 in. (152.4mm) minimum

See dimensional drawings

Top of vessel

L1 = Unmeasured

Highest

measurable

level

IL - Insertion length

distance from bottom of

process connection to the

end of the probe

L2 = Unmeasured

Lowest

measurable level

No minimum

float separation

PL - Probe length depends

on process temperature

Compression

Fitting Option

LMT SERIES | MAGNETOSTRICTIVE LEVEL TRANSMITTER LMT100 & 200 MODELS | CI/LMT100/200-EN REV. B

Specifications (Refer to LMT100/200 Datasheets for Details)

Electronic transmitter:

Repeatability ± 0.005% of Full Scale or 0.305 mm (0.012 in), whichever is greater

Non-linearity ± 0.01% of Full Scale or 0.864 mm (0.034in), whichever is greater

Measuring accuracy ± 0.01% of Full Scale or 1.27 mm (0.050 in), whichever is greater

Supply voltage 12 to 42 Vdc - 4-20mA HART loop powered

Output/Communications 4-20mA HART7®

User Interface Interactive display, DTM, EDDL with NE107 messaging

Power consumption 4-20mA at 36.0 Vdc - 3.6mA 0.13 watts; 21mA 0.76 watts

at 12.0 Vdc - 3.6mA 0.043 watts; 21mA 0.25 watts

HART mode (4.0mA) at 36.0 Vdc 0.144 watts

at 12.0 Vdc 0.048 watts

Ambient temperature -40 to 85°C (-40 to 185°F) Ambient

Humidity 0 to 100% RH

Electrical connection Two M20 x 1.5 or two 1/2in. FNPT, adapters and bus connectors also available

Ingress protection IP66, NEMA 4X

Sensor tube:

Material 316/L Stainless Steel

Process temperature LMT100: -195.5 to 121.1°C (-320 to 250°F)

Process pressure LMT100: -1.0 to 124.1 bar @ 149°C (-14.7 to 1800 psig @ 300°F)

Probe length LMT100: 304.8mm to 9.14m (1 to 30ft) / LMT200: 304.8mm to 15.24m (1 to 50ft)

CI/LMT100/200-EN Rev. B 8.2018

—

We reserve the right to make technical changes or modify the contents of this document

without prior notice. With regard to purchase orders, the agreed particulars shall prevail.

ABB does not accept any responsibility whatsoever for potential errors or possible lack of

information in this document

We reserve all rights in this document and in the subject matter and illustrations contained

therein. Any reproduction, disclosure to third parties or utilization of its contents - in

whole or in parts – is forbidden without prior written consent of ABB.

—

ABB Inc.

Industrial Automation

125 E. County Line Road

Warminster, PA 18974 USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

ABB Engineering (Shanghai) Ltd.

No. 4528, KangXin Hwy.

Pudong New District

Shanghai, 201319, P.R. China

Phone: +86 10 64231407

Service: +86 4008209696

E-mail: [email protected]om

Service e-mail: instrumentserv[email protected]

www.abb.com/level

Otros manuales para LMT100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de ABB

ABB

ABB 2600T Series Manual de usuario

ABB

ABB AW400 Series Manual de usuario

ABB

ABB TTF300 Manual de usuario

ABB

ABB 2600T Series Guía

ABB

ABB TTH300 Series Manual de usuario

ABB

ABB AWT420 Manual de usuario

ABB

ABB LST300 Series Instrucciones de funcionamiento e instalación

ABB

ABB Endura ACA592-TC Manual de usuario

ABB

ABB AquaMaster 3 FET200 Manual de usuario

ABB

ABB TTH300 Series Instrucciones de instalación

ABB

ABB LST100 Manual de usuario

ABB

ABB STT04 Manual de usuario

ABB

ABB LST400 Manual de usuario

ABB

ABB LMT Series Manual de usuario

ABB

ABB 266 HART Series Manual de usuario

ABB

ABB SLT900 Manual de usuario

ABB

ABB TB82EC Instrucciones de funcionamiento

ABB

ABB 4680 Guía de solución de problemas

ABB

ABB 2600T Series Manual de usuario

ABB

ABB AWT210 Manual de usuario

ABB

ABB PGX100 Manual de usuario

ABB

ABB 266HSH Manual de usuario

ABB

ABB 266 MODBUS Manual de usuario

ABB

ABB TTH200 Manual de funcionamiento

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario