ABB SM1000 Manual de usuario

—

ABB MEASUREMENT & ANALYTICS | INFORMATION | INF05/90 REV. E

ScreenMaster SM1000, SM2000 and SM3000

Paperless recorders

Replacing the battery

1 Introduction

This publication details the replacement of the battery (B11845)

fitted to the main board of ScreenMaster SM1000, SM2000 and

SM3000 paperless recorders. The procedure must be carried

out by a trained technician.

The battery is non-rechargeable and its only function is to

supply power to the recorder’s real-time clock when the

recorder is isolated from the power supply. It can supply power

to the clock for a minimum of 1.5 years before replacement is

required.

2 SM1000 and SM2000

Removing the main board

CAUTION

The recorder is vulnerable to electrostatic damage. Wear an

anti-static strap or dismantle the recorder on an anti-static

workbench.

Remove the main board as follows:

1 Isolate the recorder from its power supply.

2 Remove the recorder from its case – see Figure 1.

Note. Refitting is the reverse of removal.

Withdraw the recorder

from its case

Terminal cover

(if fitted)

Unscrew the

jacking screw

Remove tamper-evident seal (if fitted).

Caution. Do not break the tamper-evident

seal unless authorized to do so.

Figure 1 Removing the recorder from its case

2SCREENMASTER SM1000, SM2000 AND SM3000 | REPLACING THE BATTERY | INF05/90 REV. E

…2 SM1000 and SM2000

…Removing the main board

3 Remove the chassis top cover and PCB locking bar –

see Figure 2.

Remove PCB

locking bar

Lift up top cover

Remove top

cover

Remove screws (one each side)

and discard

Figure 2 Removing chassis top cover and PCB locking bar

SCREENMASTER SM1000, SM2000 AND SM3000 | REPLACING THE BATTERY | INF05/90 REV. E 3

4 Remove the main board – see Figure 3.

Note. Refitting is the reverse of removal.

Lift each end of the connection locking bar

carefully and disconnect the display flex-circuit

from the main board – see Note 1 SM2000 only – disconnect the touchscreen

from the main board – see Note 2

Slot D – see Note 1

See Caution

SM1000 only – disconnect the membrane switch

connector from the main board

SM1000 only – disconnect the

inverter connector from the

main board

Withdraw the main board

from the chassis

Connection locking bar

Notes.

1. To disconnect the display flex-circuit, it may be necessary to remove the I/O module board in Slot D (if fitted).

2. SM2000 main boards manufactured before March 2005 have a 4-pin tochscreen flexi-circuit and a 4-pin connector block. Main boards

manufactured from March 2005 onwards are fitted with a 6-pin connector block. When reconnecting the touchscreen flex-circuit to a

main board equipped with a 6-pin connector block, ensure it is connected to the 4 pins nearest the front of the recorder.

Caution. When fitting a main board, ensure it

locates correctly in the lugs on the chassis

base.

Figure 3 Removing the main board

4SCREENMASTER SM1000, SM2000 AND SM3000 | REPLACING THE BATTERY | INF05/90 REV. E

…2 SM1000 and SM2000

Replacing the battery

Replace the battery as follows:

1 Replace the battery – see Figure 4.

Note. Ensure the battery

positive terminal faces the

rear of the recorder.

Figure 4 Replacing the battery

2 Refit the main board – see Figure 3.

3 Refit the PCB locking bar and chassis top cover –

see Figure 5.

EMC contacts

Lower rear

Position top cover

as shown

Fit screws B12076 from

the service pack

(one each side)

Slide forward

Refit PCB locking bar

ensuring that the slots in the

bar locate correctly on the

boards and chassis

Figure 5 Refitting the PCB locking bar and chassis top cover

4 Refit the recorder to its case – see Figure 1.

5 Restore the recorder’s power supply.

6 Set the date and time – see Section 6.4.3 in the SM1000 User

Guide (IM/SM1000) or Section 4.4.3 in the SM2000 User

Guide (IM/SM2000).

3 SM3000

Removing the main board

CAUTION

The recorder is vulnerable to electrostatic damage. Wear an

anti-static strap or dismantle the recorder on an anti-static

workbench.

Remove the main board as follows:

1 Isolate the recorder from the power supply.

2 Remove the recorder from its case – see Figure 6.

Note. Refitting is the reverse of removal.

Withdraw the recorder

from its case Unscrew the

jacking screw

Remove tamper-evident seal (if fitted).

Caution. Do not break the tamper-evident

seal unless authorized to do so.

Figure 6 Removing the recorder from its case

SCREENMASTER SM1000, SM2000 AND SM3000 | REPLACING THE BATTERY | INF05/90 REV. E 5

3 Remove the main board – see Figure 7.

Note. Refitting is the reverse of removal.

Remove PCB locking bar

securing screws

(1 each side) and remove

PCB locking bar

Remove module boards as

necessary for access to

main board, noting their

positions for reassembly

Pull up each end of clamp

bar and disconnect display

flexi-cable

Remove screws (2 off)

securing main board pillars

to chassis …

Remove brace bar

securing screws

(3 off) and remove

brace bar

Disconnect

membrane switch

flexi-cable

Disconnect

inverter

… and remove

main board

1 2

3 4

Caution. When fitting a main board, ensure it

locates correctly in the lugs on the chassis

base.

7 8

Figure 7 Removing the main board

6SCREENMASTER SM1000, SM2000 AND SM3000 | REPLACING THE BATTERY | INF05/90 REV. E

…3 SM3000

Replacing the battery

Replace the battery as follows:

1 Replace the battery – see Figure 8.

Note. Ensure the battery

positive terminal faces the

rear of the recorder.

Figure 8 Replacing the battery

2 Refit the main board – see Figure 7.

3 Refit the recorder to its case – see Figure 6.

4 Restore the recorder’s power supply.

5 Set the date and time – see Section 6.4.1. of the User Guide

(IM/SM3000).

SCREENMASTER SM1000, SM2000 AND SM3000 | REPLACING THE BATTERY | INF05/90 REV. E 7

4 Notes

INF05/90 Rev. E 07.2019

—

We reserve the right to make technical changes or modify the contents of this document

without prior notice. With regard to purchase orders, the agreed particulars shall prevail.

ABB does not accept any responsibility whatsoever for potential errors or possible lack of

information in this document.

We reserve all rights in this document and in the subject matter and illustrations contained

therein. Any reproduction, disclosure to third parties or utilization of its contents – in

whole or in parts – is forbidden without prior written consent of ABB.

—

ABB Limited

Measurement & Analytics

Howard Road

St. Neots

Cambridgeshire

PE19 8EU

Tel: +44 (0)1480 475 321

Fax: +44 (0)1480 217 948

Email: instrumen[email protected]om

ABB Inc.

Measurement & Analytics

125 E. County Line Road

Warminster

PA 18974

USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

abb.com/measurement

Otros manuales para SM1000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de ABB

ABB

ABB Aztec AWT440 Manual de capacitación

ABB

ABB SM3000 Manual de usuario

ABB

ABB MagMaster Manual de usuario

ABB

ABB ICOS GLA151 Series Manual de usuario

ABB

ABB CoriolisMaster FCH400 Series Manual de usuario

ABB

ABB 2112U-101-500 Manual de usuario

ABB

ABB CoriolisMaster FCM2000 Instrucciones de instalación

ABB

ABB LevelMaster 7100 Manual de usuario

ABB

ABB NETA-21 Manual de usuario

ABB

ABB Sensyflow FMT200-D Manual de usuario

ABB

ABB AX411 Manual de usuario

ABB

ABB AK101 Manual de usuario

ABB

ABB SM500F Manual de usuario

ABB

ABB ACX Manual de instalación y operación

ABB

ABB Relion RES670 Manual de usuario

ABB

ABB NGC8200 Manual de usuario

ABB

ABB AX400 Series Manual de usuario

ABB

ABB aquamaster Manual de usuario

ABB

ABB Relion RES670 Manual de usuario

ABB

ABB FXE4000 Manual de capacitación

ABB

ABB PFCL 201 Manual de usuario

ABB

ABB VSN300 Manual de usuario

ABB

ABB PROFIBUS FEX100-DP Manual de usuario

ABB

ABB AX418 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario