ABB SM500F Manual de usuario

—

ABB MEASUREMENT & ANALYTICS | INSTRUCTION | IN/RANDC/007-EN REV. A

SM500F

Field mountable paperless recorder

Battery replacement

Measurement made easy

1 Introduction

This publication details replacement of the battery

(B12454) fitted to the processor board of the

SM500F Paperless recorder. The procedure must be

carried out by a trained technician.

Tools required

• T8 Torx driver

2 For more information

Further information is available from:

www.abb.com/recorders

or by scanning these codes:

Sales Service

3 Safety

IMPORTANT NOTE

Dispose of the old components as detailed in the

instruction manual (IM/SM500F).

SM500F

field mountable

paperless recorder

2 IN/RandC/007-EN Rev. A | SM500F | Paperless recorder | Battery replacement

4 Replacing the battery

1. Isolate the recorder from the power supply.

Referring to Fig. 4.1:

2. Unlock the door with the key (if required) A, press release

catch Band open the door.

Referring to Fig. 4.2:

3. Use a T8 Torx driver to remove 6 Torx screws Csecuring

the door assembly rear cover and remove the rear cover.

Referring to Fig. 4.3:

4. Disconnect processor board flexi-cable D, display

flexi-cable Ekeypad membrane cable Fand inverter

cable (if fitted) Gfrom the processor board. Lift out and

discard the processor board.

5. Turn the processor board over.

Referring to Fig. 4.4:

6. Remove battery Hand insert replacement.

Referring to Fig. 4.3:

7. Position the processor board in the door housing and

reconnect inverter cable G(color recorders only – if fitted)

keypad membrane cable F, display flexi-cable Eand

processor board flexi-cable D.

Referring to Fig. 4.2:

8. Refit the door assembly rear cover and use a T8 Torx driver

to secure 6 Torx screws C.

9. Close and lock the door.

10. Restore the recorder's power supply.

CAUTION – Property damage

The recorder is vulnerable to electrostatic damage.

Wear an anti-static strap or place the instrument on

an anti-static workbench.

Fig. 4.1 Opening the door

Fig. 4.2 Removing the rear cover

Fig. 4.3 Disconnecting / removing the processor board

Fig. 4.4 Replacing the battery

SM500F | Paperless recorder | Battery replacement | IN/RandC/007-EN Rev. A 3

5 Setting the time and date

1. Enter the Configuration level of the SM500F.

2. Enter password (if required) and select Edit current

configuration.

3. Select the Common configuration parameter:

The Common Configuration menu is displayed:

4. Use the arrows to highlight the Time tab:

5. Press the key to select the Date and time

parameter.

A warning dialog is displayed:

6. Press .

The Date and time menu is displayed:

7. Set the required time and date.

8. Once finished, press and exit and save the

configuration as normal.

Important note

Once the battery has been removed, the battery failed

icon is displayed on the front panel of the unit. To

restore normal operation, the correct time and date must

set.

Important note

Changing the time will potentially cause loss of

data. Ensure that all data archiving is up to date

before proceeding.

IN/RandC/007-EN Rev. A 12.2018

—

We reserve the right to make technical changes or modify the contents of this document

without prior notice. With regard to purchase orders, the agreed particulars shall prevail.

ABB does not accept any responsibility whatsoever for potential errors or possible lack of

information in this document.

We reserve all rights in this document and in the subject matter and illustrations contained

therein. Any reproduction, disclosure to third parties or utilization of its contents – in

whole or in parts – is forbidden without prior written consent of ABB.

—

ABB Limited

Measurement & Analytics

Howard Road, St. Neots

Cambridgeshire, PE19 8EU

Tel: +44 (0)0870 600 6122

Fax: +44 (0)1480 213 339

Email: instrumen[email protected]om

ABB Inc.

Measurement & Analytics

125 E. County Line Road

Warminster

PA 18974

USA

Tel: +1 215 674 6000

Fax: +1 215 674 7183

abb.com/measurement

Otros manuales para SM500F

Otros manuales de Instrumento de medición de ABB

ABB

ABB WVM Series Manual de usuario

ABB

ABB EL3000 Series Manual de usuario

ABB

ABB aquamaster s Manual de usuario

ABB

ABB VLMD-1-2 Manual de usuario

ABB

ABB D1M 20 Manual de usuario

ABB

ABB AX400 Series Manual de usuario

ABB

ABB PositionMaster EDP300 Manual de usuario

ABB

ABB MicroGuard solution Manual de usuario

ABB

ABB Endura AZ20 series Manual de usuario

ABB

ABB EXCOUNT-II Manual de usuario

ABB

ABB Gas Sampling Probe 2 Manual de usuario

ABB

ABB VortexMaster FSV430 Instrucciones de instalación

ABB

ABB PointMaster 200 Series Manual de usuario

ABB

ABB CoriolisMaster FCM2000 Instrucciones de instalación

ABB

ABB Navigator 550 Manual de usuario

ABB

ABB ScreenMaster RVG200 Manual de usuario

ABB

ABB Navigator 600 Silica Manual de usuario

ABB

ABB CoriolisMaster FCM2000 Manual de usuario

ABB

ABB JDF300 Manual de usuario

ABB

ABB Relion 670 Series RES670 Manual de usuario

ABB

ABB Aztec 600 Manual de usuario

ABB

ABB 600T Series Manual de usuario

ABB

ABB KM26 Manual de usuario

ABB

ABB AnalyzeIT 7600 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario