ABB FCAN-01 Manual de instalación

Options for ABB drives, converters and inverters

Quick installation and start-up guide

FCAN-01 CANopen adapter module

Safety instructions

WARNING! Obey the safety instructions. If you ignore them, injury or death, or damage to the

equipment can occur. See the user’s manual.

Mechanical installation

Electrical installation

Layout of the module

1. Pull out the lock.

2. Install the module carefully to an option

module slot of the drive. See the drive

hardware manual.

3. Push in the lock.

4. Tighten the screw to torque 0.8 N·m using

a Torx TX10 screwdriver.

WARNING! Do not use excessive force,

or leave the screw too loose. Over-

tightening can damage the screw or

module. A loose screw decreases the EMC

performance, and can even cause an operation

failure.

No. Description

1Lock

2 Mounting and grounding screw

3 Bus connector [X1]

4 Diagnostic LEDs

Start-up

When the module is connected to the drive, the drive control program sets the applicable parameters.

See the appropriate drive manual.

Basic parameter settings

To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par refresh.

Further information

Index Name Value

20.01 Ext1 commands Fieldbus A

22.11 Speed ref1 source FBA A ref 1

28.11 Frequency ref1 source FBA A ref 1

50.01 FBA A enable Enable (or select the option slot in which the module is installed)

50.02 FBA A comm loss func Fault

51.02 Node ID Set the node address of the device.

51.03 Bitrate Set the bit rate for the CANopen interface.

51.05 Profile The ABB Drives communication profile is the default value.

See the latest version of FCAN-01 CANopen adapter

module user's manual (3AFE68615500 [English]) in ABB

library (www.abb.com/drives/documents).

For more information on fieldbus options and protocols

provided by ABB Drives, see the fieldbus

communications web page

(new.abb.com/drives/connectivity/fieldbus-connectivity).

Pin allocation for [X1] Bus termination

Bus termination is required to prevent signal reflections

from the bus cable ends. The module is not equipped with

internal bus termination. Therefore, the first and last

nodes of the bus must be included with bus termination.

In the this diagram, the built-on terminations of the D-SUB

connectors at the first and last nodes are switched on.

According to CANopen specification CiA 301.

Pin Description

1 - Not in use

2 CAN_L CAN_L bus line

3 CAN_GND CAN ground

4 - Not in use

5 CAN_SHLD Optional CAN shield

6 GND Optional ground

7 CAN_H CAN_H bus line

8 - Not in use

9 CAN_V+ Not supported.

SUB-D9

(male)

CANopen

CANopen CANopenCANopen

OFF

OFF ON

3AXD50000158195 Rev A (EN) 2017-11-23

FCAN-01 manual

Fieldbus communications web page

Otros manuales para FCAN-01

Tabla de contenidos

Otros manuales de Unidad de control de ABB

ABB

ABB OMD200 Guía del usuario

ABB

ABB ACS580-04 Manual de usuario

ABB

ABB RER 103 Instrucciones de funcionamiento e instalación

ABB

ABB HD5-B Series Manual de usuario

ABB

ABB ACL30-04 Series Guía de solución de problemas

ABB

ABB RELION 650 SERIES Guía de inicio rápido

ABB

ABB RER 133 Manual de lista de piezas

ABB

ABB ACS880-04F Manual de usuario

ABB

ABB Relion REC670 Instrucciones de uso

ABB

ABB RDIO-01 Manual de usuario

ABB

ABB XIO-00 Manual de usuario

ABB

ABB MOD 30ML Manual de usuario

ABB

ABB Arc Guard System TVOC-2 Manual del producto

ABB

ABB BCU-01 Manual de usuario

ABB

ABB ACSM1 Series Manual de uso y cuidado

ABB

ABB Busch-priOn Series Manual del producto

ABB

ABB 616016-T2 Manual de uso y cuidado

ABB

ABB Relion 615 series Manual de instalación y operación

ABB

ABB EAS822 Manual de usuario

ABB

ABB REF542plus Manual de usuario

ABB

ABB LEANtouch 6x36/30M-500 Series Manual de usuario

ABB

ABB THQ Guía del usuario

ABB

ABB Welcome M2307 Guía de configuración

ABB

ABB ACQ580-34 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario