ABB FAIO-01 Manual de usuario

—

OPTIONS FOR ABB DRIVES, CONVERTERS AND INVERTERS

FAIO-01 analog I/O extension module

User's manual

FAIO-01 analog I/O

extension module

User's manual

Table of contents

1. Safety instructions

4. Installation

5. Start-up

3AUA0000124968 Rev C

EFFECTIVE: 2019-12-05

Table of contents

1 Safety instructions

7Contents of this chapter ............................................................

7Use of warnings ........................................................................

8Safety in installation ..................................................................

2 Introduction to the manual

9Contents of this chapter ............................................................

9Target audience ........................................................................

9Compatibility .............................................................................

10Terms and abbreviations ...........................................................

3 Hardware description

11Contents of this chapter ............................................................

11Product overview ......................................................................

12Layout .................................................................................

4 Installation

15Contents of this chapter ............................................................

15Unpacking and examining the delivery .....................................

15Installing the module .................................................................

16…onto the drive control unit ...............................................

17…onto an extension adapter module .................................

17Selecting the input mode, voltage range and signal type .........

18General cabling instructions .....................................................

18Wiring ........................................................................................

Connection example for motor winding temperature

measurement ......................................................................

19Connection example for external devices ..........................

5 Start-up

21Contents of this chapter ............................................................

21Before you start .........................................................................

22Setting the parameters ..............................................................

22Example – Primary control program ...................................

Table of contents 5

6 Diagnostics

23Contents of this chapter ............................................................

23Faults and warning messages ..................................................

23LEDs .........................................................................................

7 Technical data

25Contents of this chapter ............................................................

25Data ..........................................................................................

25Degree of protection ...........................................................

25Ambient conditions .............................................................

25Package ..............................................................................

26Hardware settings ...............................................................

26A/D conversion resolution ..................................................

26Isolation areas ....................................................................

27Analog inputs and outputs ..................................................

27Power supply ......................................................................

27General ...............................................................................

28Dimensions ...............................................................................

Further information

6 Table of contents

Safety instructions

Contents of this chapter

The chapter contains the warning symbols used in this manual and

the safety instructions which you must obey when you install or

connect an optional module to a drive, converter or inverter. If you

ignore the safety instructions, injury, death or damage can occur.

Read this chapter before you start the installation.

Use of warnings

Warnings tell you about conditions which can cause injury or death,

or damage to the equipment. They also tell you how to prevent the

danger. Notes draw attention to a particular condition or fact, or give

information on a subject.

The manual uses these warning symbols:

Safety instructions 7

WARNING!

Electricity warning tells about hazards from electricity which

can cause injury or death, or damage to the equipment.

WARNING!

General warning tells about conditions, other than those

caused by electricity, which can cause injury or death, or

damage to the equipment.

Safety in installation

These instructions are for all who install or connect an optional module

to a drive, converter or inverter and need to open its front cover or

door to do the work.

WARNING!

Obey these instructions. If you ignore them, injury or death,

or damage to the equipment can occur. If you are not a

qualified electrical professional, do not do electrical installation

or maintenance work. Go through these steps before you begin

any installation or maintenance work.

•Disconnect the drive, converter or inverter from all possible power

sources. After you have disconnected the drive, converter or

inverter, always wait for 5 minutes to let the intermediate circuit

capacitors discharge before you continue.

• Disconnect all dangerous voltages connected to other control

signal connectors in reach. For example, it is possible that

230 V AC is connected from outside to a relay output or digital

input of the drive, converter or inverter.

• Always use a multimeter to make sure that there are no parts

under voltage in reach. The impedance of the multimeter must

be at least 1 Mohm.

8 Safety instructions

Introduction to the manual

Contents of this chapter

This chapter introduces this manual.

Target audience

This manual is intended for people who plan the installation, install,

commission, use and service the extension module. Before you do

work on the module, read this manual and the applicable drive,

converter or inverter manual that contains the hardware and safety

instructions for the product in question.

You are expected to know the fundamentals of electricity, wiring,

electrical components and electrical schematic symbols.

The manual is written for readers worldwide. Both SI and imperial

units are shown.

Compatibility

See the appropriate hardware manual.

Introduction to the manual 9

Terms and abbreviations

DescriptionTerm

Frequency converter for controlling AC motorsDrive

Electromagnetic compatibilityEMC

Optional analog I/O extension moduleFAIO-01

10 Introduction to the manual

Tabla de contenidos

Otros manuales de Unidad de control de ABB

ABB

ABB Welcome M2306 Manual de usuario

ABB

ABB FCAN-01 Manual de instalación

ABB

ABB 616019-T1 Manual de uso y cuidado

ABB

ABB UCU-22 Manual de usuario

ABB

ABB REC650 ANSI Guía de inicio rápido

ABB

ABB i-bus EIB Manual de usuario

ABB

ABB COM600 series Manual de usuario

ABB

ABB Relion REC670 Instrucciones de uso

ABB

ABB RELION Series Manual de usuario

ABB

ABB Symphony Harmony Series Manual de usuario

ABB

ABB ACS 600 MultiDrive Manual de usuario

ABB

ABB Relion 670 series Guía de inicio rápido

ABB

ABB ACS880-04 drive modules Manual de usuario

ABB

ABB Relion 630 Series Guía de inicio rápido

ABB

ABB FCB400 Series Manual de usuario

ABB

ABB Relion SAM600-IO Manual de usuario

ABB

ABB MPS-C 2000 Manual de usuario

ABB

ABB HD5-B Series Manual de usuario

ABB

ABB i-bus KNX Manual de usuario

ABB

ABB Arc Guard System TVOC-2 Manual del producto

ABB

ABB CP1484 Manual de usuario

ABB

ABB ACQ810 Manual de usuario

ABB

ABB Relion 670 series Guía de inicio rápido

ABB

ABB OHDI-01 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario