3M Edge Manual de usuario

3M Occupational Health and Environmental Safety Division

3MTM The Edge Personal Noise Dosimetry

Quick Start Guide

The Edge

Turning on

1. Turn on the Edge by pressing and releasing the key.

Resetting

Resetting the Edge is performed by either using the 3MTM

Detection Management Software DMS when downloading

or setting up parameters. Another option is from the Edge’s

shortcut reset menu.

• To reset from the keypad ensure the Edge is off, then:

1. Press key.

2. Press and hold and keys when the splash screen

appears. The shortcut menu will appear (see below).

3. Press the up arrow until the reset icon is selected.

4. Press and hold the key until it shows the les were

deleted.

• A 3, 2, 1 countdown and a shaded bar indicates reset.

5. To exit, press down arrow until icon is selected. Press

key.

Edge Display and Keypad

Microphone and

windscreen

LED Indicator

•Red - indicates dose has exceeded the alarm level.

• Amber - indicates stopped.

• Green - indicates measuring.

Measurement display

Up arrow

Down arrow

On/Off/Enter key

Run/Stop key

Reset icon

Contrast icon

Exit icon

LED Indicator

•Red - indicates dose has exceeded the alarm level.

• Amber - indicates stopped.

• Green - indicates measuring.

Calibrating

A calibration may be performed before and/or after a

dosimetry test.

1. Remove the windscreen while the Edge is turned on

and stopped.

2. Slide the Edge into the cavity of the

calibrator, ensuring the adapter

ring is inserted into the calibrator.

3. Turn on the calibrator. Set the

calibrator to 114 dB and 1000 Hz

(if applicable).

4. “CAL” will ash on the Edge display

automatically detecting the calibration

screen.

5. Press the key to trigger the calibration screen.

6. To adjust the calibration value on the display, repeatedly

press the up/down arrows to match 114.0 dB.

7. Press key to exit.

Viewing and/or navigating data

1. Press the the up/down arrow keys to navigate through the

measurements and parameters.

Setting up the Edge

All the Edge parameters are setup via 3MTM Detection

Management Software DMS in the Instrument Communication

panel or button from the DMS start screen.

Running a study

Ending a study

1. Press and hold the on/off enter button for the count

down.

Turning off

1. Once the Edge is turned on, press and hold the button.

• A 3, 2, 1 countdown will appear. Then, a run indicator

will appear on the top of the display. Also the LED will

ash green unless this was disabled in the DMS via the

heartbeat eld.

1. While running a study, press and hold the run/stop

button.

• A 3, 2, 1 countdown will appear and the indicator will

appear on the top of the display.

Screen indicators: in run mode

1. To communicate with DMS and the Edge, turn on the Edge

and plug in the USB cable from the edge to the pc. Then,

open 3MTM Detection Management software DMS.

2. Click on the button. The instrument communications

panel will appear. Select the Edge instrument and model from

the dosimetry family.

3. Click on the Edge(s) check boxes in the EdgeDock-5 section and

then select the button.

• DMS will stated Download completed. Select the Data Finder tab

to view your data (if not automatically selected.)

Downloading data and DMS

Locking/unlocking

1. Turn the dosimeter on and press the button to start

measuring.

2. To enable the lock, press button. Then press

three consecutive times, within one second intervals.

3. To unlock, press the button within on second intervals

and then press button.

Communicating DMS start screen

Occupational Health &

Environmental Safety Division

Quest Technologies, a 3M Company

ISO 9001 Registered Company

ISO 17025 Accredited Calibration Lab

1060 Corporate Center Drive

Oconomowoc, WI 53066

Customer Service: 262-567-9157

Toll Free: 800-245-0779

www.3m.com/detection

Please recycle. Printed in USA.

© 2012 3M

All rights reserved.

098-610 Rev.E 3/12

Tabla de contenidos

Otros manuales de Instrumento de medición de 3M

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario