3Com WL-306 Manual de usuario

WL-306 Test Instructions

IMPORTANT NOTES – Please read before testing.

i) You must read the “Power Levels Changing” section before testing so that the

power levels can be set correctly prior to test. See also “Antenna Selection”

below, make sure you select the correct antenna (e.g. “a 0” or “a 1”)

depending upon whichever you are connected to.

ii) All commands are case sensitive and therefore they must be entered precisely

to avoid problems. You can check the cases of each command by entering the

Help commands as detailed below.

iii) Only use the TOP PCMCIA card slot for all the PC Cards. DO NOT used the

blanked off lower slot.

1) Card Installation:

The WL-306 has been installed in the PC’s provided and you must follow the following

instructions precisely to enable it for testing.

Set up the equipment as detailed in the test set up diagram.

When you initially boot up the PC you will get a “3Com OfficeConnect- Wireless Client

Set up” Prompt. Press the cancel button and then proceed as follows:

Click on the “WL-305” icon on the PC desktop.

You should now be at the following prompt

C:\Speedracer

Type in the following command:

C:\Speedracer Set poldebugmac=00-aa-bb-cc-dd-ee

Then: C:\Speedracer Poldebug X {Where X=2 when using the HP PC and X=4 When

testing with the Sony PC}

You are now in “receive mode” and at the debugging prompt ready to test. If you already

have other WLAN equipment transmitting you will see the received data scrolling on the

screen.

2) Setting the WL-306 into Trasmission

Type in the following commands precisely during test noting the spaces and case

(upper/lower) of the commands. Note you only need to enter the commands in BOLD.

r 0 {This will turn the receive mode off and enable you to transmit}

c 1 {This will select channel 1. Similarly you can perform testing on any of

the other channels by typing “c x” where x is the channel number}.

a 1 {This will select antenna connection B. Alternatively you can choose Antenna

connection A using command “a 0” however this is the default setting so it is not

required unless you are changing from Antenna B to A}.

pc 127 {Modifies power level setting from 143 to 127}

tc {Transmit mode = Continuous}

{Note: The above “tc” command sets a continuous number of packets which will be

transmitted after the “T” command below is initiated. If you only need to transmit for a

shorter time you can limit the number of packets by using the “t xxxxx” command where

xxxx is the number of packets. For example t 3000 will transmit for approximately 1

minute. Simply increase the number accordingly for the time required.

T{Start transmitting}

{You can check the power level using the command “pc” only once the “T” command

has started transmission. Use of this command at any other time may cause the power

level to default to an incorrect power level setting}

Changing Channels:

Once the WL-306 is transmitting, as detailed above, the channels can be changed simply

as follows. At the Debugging enabled prompt type:

c x {You can set the channel to anywhere between 1-14 by entering this command

where x is the channel number required. The new channel should adopt the same

properties (e.g. power levels etc) as the previous channel. If you are in any doubt

as to whether this is the case then remove the orange cable from the WL-306, re-

insert the cable and then repeat the commands from 2) above this time entering

the new required channel number}

Turning On/Off modulation:

You can select a signal with or without modulation using the following commands once

the WL-306 is transmitting.

At the Debugging enabled prompt type:

cw 0 {Turns on modulation}

cw 1 {Turns off modulation}

Antenna Selection:

On the open card there are two antenna connectors for the conducted testing as detailed in

the attached diagram. You can select between these two using the following command:

At the Debugging enabled prompt type:

a 0 {to select Antenna connection A}.

a 1 {to select Antenna connection B}

You will see a big change in the power levels if you switch between correct/incorrect

settings so please make sure that you are testing with the correct (maximum) setting.

Bit Rate selection:

The data rate can manually be selected using the following commands however it will

automatically drop, with distance, to the maximum possible under the connection

conditions.

At the Debugging enabled prompt type:

tr 110 {Sets to 11MBps}

tr 10 {Sets to 1MBps}

tr 20 {Sets to 2MBps}

tr 50 {Sets to 5MBps}

Setting up a connection to demonstrate the ETS 300 826 immunity test:

All the above tests can be performed using just one unit and one PC. I have also sent

you a WL-305 PC Card so that you can perform the ETS 300 826 tests and demonstrate

the connection. To do this please set up as follows:

The following example sets the Access Point (WL-306) to transmit a user specified (x)

number of packets to a WL-305 PC Card using channel 1.

Transmit PC from WL-306 (Use PC RA&A 73)

Click on the WL-306 icon on the desktop to bring you to the DOS prompt c:\speedracer

Type the following at the DOS prompt

C:\speedracer set poldebugmac=00-aa-bb-cc-dd-ee

C:\speedracer poldebug 4

{You should now be at the de-bugging prompt}.

>c 1 {Select the low channel}

>tc

Set up the Receive PC as below then send the packets.

>t 10000 {Transmitting 10000 packets. This takes approximately 75 seconds. To

transmit for more time simply increase the number of frames}.

>T {Starts Transmitting the packets. If you cannot see them being received on

the PC Card then ensure that the channel is set identical to above and that

the card is set to receive (r 0)}

Receive PC using PC Card WL-305 (Use PC Card set up in PC RA&A74)

These 10000 packets can be viewed on the Receive PC set up as follows.

Insert the WL-305 PC Card

Click on the WL-306 icon

At the DOS prompt enter the following command:

C:\speedracer poldebug 6.

{You should now be at the debugging prompt for the WL-305. Please then enter the

following commands to show the received data}

>c 1 {To select the same channel as the send}

>r 1 {To enable display on the receive}

You will then see:

“Good frame…….” Being displayed on the receive as each packet is received.

>RXSTATS {Type this to display information on the received packets. It will show

Total number of packets received, good packets and packets with CRC

errors.

NOTE: There is a bug in the program which always shows 7 CRC errors. This is the

same whether you send 10000 or 20 frames}

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de 3Com

3Com

3Com OfficeConnect 3CRWE454G75 Manual de usuario

3Com

3Com WL-455 Manual de usuario

3Com

3Com AirConnect 9550 Guía de instalación

3Com

3Com 3CRWEASYA73 / WL-575 Manual de usuario

3Com

3Com 3CRWE870075A - Wireless LAN Access Point... Manual de usuario

3Com

3Com 8200 Manual de usuario

3Com

3Com WL-607 Manual de usuario

3Com

3Com 3CRWX315075A - Wireless LAN Managed Access Point... Manual de usuario

3Com

3Com 3CRWEASYG73 - 11g Wireless LAN Outdoor Manual de usuario

3Com

3Com 3CRWE876075 / WL-546 Manual de usuario

3Com

3Com 3CRWE20096A - Wireless LAN Access Point 2000 Manual de usuario

3Com

3Com LANplex 6000 Manual de usuario

3Com

3Com 7250 Manual de usuario

3Com

3Com 7760 - Wireless 11a/b/g PoE Access Point Manual de usuario

3Com

3Com 3CRGPC10075 Manual de usuario

3Com

3Com AP9152 Manual de usuario

3Com

3Com 3CRWX275075A - Wireless LAN Managed Access Point... Manual de usuario

3Com

3Com AirConnect Manual de usuario

3Com

3Com 7608 Manual de usuario

3Com

3Com 8250 Manual de usuario

3Com

3Com 3CRWE920G73 Manual de usuario

3Com

3Com 8000 Manual de usuario

3Com

3Com 3CRWX375075A - Wireless LAN Managed Access Point... Manual de usuario

3Com

3Com 8500 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario