ZZ2 ITZ-CDR31-A Manual de usuario
09/20/2022
Apple Car Play
ITZ-CDR31-A
CarPlay / Android Auto + Camera input for Porsche vehicles
equipped with the CDR31 NON-NAV System
929-220-1212 / 877-241-2526 - www.zz-2.com
Components
ZZPlay Interface
BT/WIFI SMB Antenna
Main Harness
Touch/Video PCB Module
Modification Ribbon
Velcro for module
Switching/LVDS Harness
Touch Cable
Microphone
(optional)
09/20/2022
CDR31 Radio Modification
1. Remove the
radio from the
dashboard and
bring to a bench
top for
modification.
Use something
soft to protect
from scratches.
2. Remove (2x)
screws from the
top of the radio
face.
3. Using a small flathead screwdriver, carefully pry all clips (while applying pressure to
remove screen) around the plastic radio face. The entire front LCD panel and button panel is
connected vis ZIF connectors only (no ribbons to the radio chassis).
4. Lay the front panel
assembly down (face
down) on a soft mat.
Disconnect (2x)
ribbons shown.
5. Orient the provided modification ribbon like shown below. Connect the wider
ribbon into the wider connector as show. Make sure the pin-side faces down on
this step.
6. Carefully and slowly (do not tear ribbon), flip the ribbon over such that the smaller
touch-ribbon side lines up with the OE 4-pin touch connector. Once again, the pin-side
of the 4-pin ribbon must face downwards.
7. Once the ZZ2 ribbon is
connected to the board,
connect the leftover OE
ribbons back to the ZZ2
ribbon. When this step is
completed, it should look
like picture here (right)
8. Using pliers (or
similar method), cut
off 1 metal tab from
the radio chassis
mount as shown.
9. Using cloth tape (or similar method), lay over the serrated edge from tab removal
(step 8) to protect the ribbon. Be very cautious when lining up the screen face to the
ZIF connectors (there are alignment pegs towards the middle to help). Also pay close
attention to the exiting ribbon when connecting so as to not pinch/sever anything.
10. Route the ribbon
like shown leaving slack
along the way. Tape
down as you feel
necessary to route to
the back side of the
radio.
11. Connect the provided
Touch/Video PCB Module
to the back side of the
radio like shown using
the double-sided tape. It
is best to leave a 1/4" of
space between the left
and bottom edge for ease
of installation back into
the sub-dash.
CDR31
Installation
Diagram
Notes:
- The radio must be in 'AUX'
mode in order for audio
playback through the OE
speakers.
- Make certain the OE Fiber-
Optic cables are removed from
the OE radio plug and moved to
the radio side of the T-Harness.
-If using (green) reverse wire
trigger, 'Reversing Mode' must
be set to '12V Active' inside Car
Setting menu.
-If adding Aftermarket camera,
'Reversing Camera' must be set
to 'Aftermarket Camera' inside
Car Setting menu.
09/20/2022
DIP Switch Settings
OFF:
ON:
Disconnect power before adjusting dip switches.
ATTENTION: RADIO
MUST BE ON AUX
MODE TO HEAR
AUDIO FROM
CARPLAY THROUGH
THE SPEAKERS
User Operation
09/20/2022
All CarPlay/AA/Interface
commands are
performed on the touch
screen for CDR31.
Switch IN and OUT to OE
mode to interface by
pressing and holding the
provided external switch
(below)
Controlling CarPlay/
Android Auto is used
fully via the touch
screen. NOTE: If after
installation there is a
problem with touch
response, press and
HOLD the screen for
12 seconds to calibrate
touch screen.
•How to connect to Apple CarPlay / How to setup Bluetooth Phone Calls
1. If you would like to use a cable to
connect your iPhone, please use a
certified Apple cable.
2. If you would to use a wireless
connectivity, please follow the next
steps.
3. Before pairing the iPhone with the
system, please make sure you do a
"hard reset" on the phone in order to
prevent any malfunction. (Check
phone manual/online)
4. Once you are done with the previous
step go to Settings > Bluetooth and
the phone should be able to find a
Bluetooth device called ZZPLAY*****
under the Other Devices.
4. Select ZZPLAY***** and a Bluetooth
Pairing Request will be displayed on
the screen with a code. Select "PAIR".
5. Right after the Pairing notification a new
request to Sync your contact with the car
will be displayed. Select "ALLOW" in order
to have caller ID and access to your
contacts through CarPlay.
6. A notification asking for a permission to
connect your iPhone to the car even when
the phone is locked will pop up. Select
"Use CarPlay" and the CarPlay main
screen should show up on the factory radio
screen.
7. When the phone is connected and
paired properly, the screen will
automatically switch to CarPlay. Once you
are in CarPlay mode, if ever necessary,
select the ZZ2 app to go to the interface's
main menu.
09/20/2022
For uninterrupted USB
Audio Playback
For Screen-Mirroring
iPhone & Android devices.
To view
Bluetooth devices
To enter
CarPlay Mode
All Settings Menu for
interface
For uninterrupted
USB Video Playback
Currently connected devices
To view (typically front)
connected camera
To enter Android
Auto Mode
ZZPLAY Interface
Main Menu
Car Setting:
Allows adjustments for
camera(s) and MIC options.
These options are specific to
the how the interface
handles camera triggers and
types (data vs analog wire,
OEM vs aftermarket etc). A
few other vehicle-specific
settings can be found here as
well.
General:
Allows adjustments for global
volume control and
navigation (specific) volume
control output. Also there is
an option for auto-pairing the
user’s handset.
Selecting ‘Settings’ will bring you to the ZZPLAY Interface Setup
Menu with all options pertaining to the specific vehicle and install.
The next few pages overview the ZZPLAY interface, navigating settings and explains
entering/exiting all menus. There are (2) menu systems that exist outside of the OE radio
system: Carplay (or Android Auto) menu and the ZZPLAY Interface Menu. They operate
independent of each other (the ZZPLAY Interface menu will function regardless of whether or
not a phone is connected to the module). Settings found inside Carplay will only affect
CarPlay functionality. Settings for the ZZPLAY Interface control things like reverse camera
settings, audio output control settings and other vehicle/interface-specific parameters.
CARPLAY
ZZPLAY INTERFACE MENU
To enter the ZZPLAY Interface Menu from the
CARPLAY system, locate the
ZZPLAY tile and select it. If there is no phone
connected, simply using the activation button
(which normally brings you into CARPLAY mode)
will enter you in the ZZPLAY Interface Menu.
ZZPLAY Interface Settings Menu
09/20/2022
Tabla de contenidos
Otros manuales de Accesorios para automóviles de ZZ2
