ZyXEL Communications C3000Z Manual de usuario

Quick Start Guide

www.zyxel.com

C3000Z

WiFi-N/AC 2.4G 3x3 /5G 4X4 VDSL2 4-port

Bonding Combo WAN IAD

Version CZD001-4.16.002.0

Edition 1, 04/2017

Default Login Details

LAN IP Address http://192.168.0.1

User Name admin

Password Check the device label

Quick Start Guide

Device Panels

POWER

DSL

INTERNET

ETHERNET

USB SLOT

POWER

RESET

DSL PORT

USB

ETHERNET 1-4

WIFI 2.4G

WAN/LAN

LAN/WAN

PORTS 1-4

WPS

BUTTON

PORT

WIFI 5G

Overview

The Device is a VDSL2 bonding integrated access device (IAD) with a

four-port built-in Ethernet switch and IEEE 802.11ac wireless. The

Device allows wired and wireless clients to safely access the Internet.

Additionally, the Device includes a Gigabit Ethernet LAN port that can

also serve as a WAN connection to support a dual WAN function. The

USB port allows you to connect a USB memory stick or USB hard drive

for storing or sharing files through the network.

Requirements

Make sure you have the following things before you start.

• Internet access - account information provided by your ISP, such as

user name, password, and so on.

• Internet Explorer 8.0 and later versions, with JavaScript enabled, or

Mozilla Firefox 14 and later versions.

Hardware Connections

1. Use a telephone cable to connect your Device’s DSL port to a

telephone jack (or the DSL or modem jack on a splitter if you have

one).

2. ETHERNET: Use an Ethernet cable to connect a computer to a LAN

port for initial configuration and/or Internet access.

3. USB: You can connect a USB memory stick or a USB hard drive for

file sharing. The Device automatically detects the USB device.

Alternatively, use a USB cable (not provided) to connect a USB

printer to this port.

4. POWER: Use the provided power adaptor to connect the POWER

socket to an appropriate power source. Make sure the power at the

outlet is on. Look at the lights on the front panel.

•ThePOWER light blinks while your Device starts up and then stays

solid green once it is ready.

•TheDSL lights are solid green after your Device has a DSL

connection.

•TheINTERNET light turns on when the Device is able to access the

Internet and blinks when the Device is sending or receiving data.

•TheWAN/LAN light is on if the WAN/LAN port is properly connected

and blinks when there is traffic.

• Each ETHERNET light is on if the corresponding LAN port is

properly connected and blinks when there is traffic.

•TheUSB light turns on when there is a USB printer or memory

device is connected to the Device and blinks when transmitting data.

•TheWiFi 2.4G light is green when the wireless LAN is ready and

blinks when there is traffic.

•TheWiFi 5G light is green when the wireless LAN is ready and

blinks when there is traffic.

•TheWPS light is green when WPS is enabled and blinks amber

while WPS is in process.

If the lights do not come on, check your connections and inspect your cables

for damage. If the lights are still off, contact technical support.

Internet Connection Setup

Your Device can automatically detect and configure your Internet

connection once the hardware is connected properly.

Automatic Connection

1. Open your web browser to a website. Wait while your Device tries to

detect your DSL connection to your ISP. This may take a few

minutes.

2. After it detects the connection, the DSL lights show amber on your

Device and the INTERNET light comes on when the Internet is ready

for you to use. If you have a PPPoE connection, you will have to

enter the user name and password provided by your ISP.

3. Go to Set Up a Wireless Network if you wish to configure your

wireless settings.

4. If the automatic connection is not successful, check your connections

and restart the Device. Also, make sure you have entered the user

name and password correctly. If you still cannot access the Internet,

follow the steps in the next section to manually configure the Internet

connection.

Manual Connection

You can also manually log into the Device’s Web Configurator and

configure the Internet connection.

1. In your browser, if the Device does not automatically re-direct you to

the login screen, go to http://192.168.0.1.

2. Enter the default user name admin and password (see the Device’s

label). Click Apply.

If the login screen does not open, make sure you allow web browser pop-up

windows, JavaScripts and Java permissions. Your computer should be also

set to get an IP address automatically from a DHCP server.

3. The main screen appears. Click Quick Setup to configure the

Device’s Internet access.

4. Enter the user name and password provided by your ISP. Click Apply

to finish the configuration.

5. The DSL lights are green on your Device and the INTERNET light

comes on when the Internet is ready for you to use. If you still cannot

access the Internet, contact your ISP.

Set Up a Wireless Network

You can set up a wireless network using the following methods:

Using Wireless Protected Setup (WPS)

Press the WPS button on the Device’s front panel for more than 5

seconds to turn the WPS function on.

Follow these steps to add a WPS-enabled device to the wireless

network using the WPS button.

Set Up a Wireless Network Manually

The wireless LAN on your Device is enabled by default. To add a

wireless client to the network, use the settings found on the bottom panel

of your Device.

Configure wireless devices that you want to connect to the wireless

network to use the same wireless settings as the Device.

The default wireless settings vary for each Device. Refer to the label of

your Device and use the provided information.

Place the devices you

want to connect near one

another.

Press the WPS button on

the Device.

Press the WPS button on

a compatible device

within 2 minutes of

pressing the button on

the Device.

The WPS light on the

Device blinks amber

when connection is in

progress and is solid

green when connected.

WPS

1010

Wall Mounting

The following are dimensions of a screw anchor and M4 tap screw used

for wall mounting. All measurements are in millimeters (mm).

1. Locate a high position on a wall that is free of obstructions. Use a

sturdy wall.

2. For a concrete or brick wall find a drill bit with the same diameter as

the screw anchors. If you do not need the screw anchors, find a drill

bit slightly smaller in diameter than the included screws.

3. Drill the two screw holes in the wall. Make sure the distance between

the centers of the holes is the same as the wall-mount holes.

Be careful to avoid damaging pipes or cables located inside the

wall when drilling holes for the screws.

Tabla de contenidos

Otros manuales de Módem de ZyXEL Communications

ZyXEL Communications

ZyXEL Communications AAM1008-61 Manual de instrucciones

ZyXEL Communications

ZyXEL Communications XMG5101-S10A Manual de usuario

ZyXEL Communications

ZyXEL Communications 2864 Series Manual de usuario

ZyXEL Communications

ZyXEL Communications P630M Manual de usuario

ZyXEL Communications

ZyXEL Communications Omni 56K Manual de usuario

ZyXEL Communications

ZyXEL Communications Prestige 642 Manual de usuario

ZyXEL Communications

ZyXEL Communications P-871M Manual de instrucciones

ZyXEL Communications

ZyXEL Communications P-870M-I1 V2 Manual

ZyXEL Communications

ZyXEL Communications Prestige 941 Manual de usuario

ZyXEL Communications

ZyXEL Communications PMG1005-T20B Manual de usuario

ZyXEL Communications

ZyXEL Communications ONU-2024 Series Manual de usuario

ZyXEL Communications

ZyXEL Communications P-2612HW-F1 - Manual de usuario

ZyXEL Communications

ZyXEL Communications WiMAX XOHM Guía

ZyXEL Communications

ZyXEL Communications Omni 288S Manual de usuario

ZyXEL Communications

ZyXEL Communications U-90E Manual de usuario

ZyXEL Communications

ZyXEL Communications P-870M-I Series Manual de usuario

ZyXEL Communications

ZyXEL Communications P-630-S Series Manual

ZyXEL Communications

ZyXEL Communications IES-612-51A Manual de usuario

ZyXEL Communications

ZyXEL Communications U-1496 series Manual de usuario

ZyXEL Communications

ZyXEL Communications NBG-419N Manual de usuario

ZyXEL Communications

ZyXEL Communications XOHM MAX-206M2 Manual de usuario

ZyXEL Communications

ZyXEL Communications IES-1248-51 Manual de usuario

ZyXEL Communications

ZyXEL Communications P-971M Manual de usuario

ZyXEL Communications

ZyXEL Communications P-600 Series Guía de referencia

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario