ZyXEL Communications Internet Security Gateway ZyWALL 100 Manual de usuario

ZyWALL 100

Internet Security Gateway

Quick Start Guide

Version 3.52

March 2003

ZyWALL 100

Introducing the ZyWALL

The ZyWALL 100 is the ideal secure gateway for all data passing between the Internet and the LAN. By

integrating NAT, firewall, VPN capability and wireless LAN, ZyXEL’s ZyWALL 100 is a complete security

solution that protects your Intranet and efficiently manages data traffic on your network. The embedded web

configurator is easy to operate and totally independent of the operating system platform you use.

You should have an Internet account already set up and have been given most of the following information.

Internet Account Information

Your device’s WAN IP Address (if given): __________________

DNS Server IP Address (if given): Primary __________________, Secondary _________________

Encapsulation:

 Ethernet Service Type: _______________________

User Name: ____________ Password: ____________

 PPTP User Name: ____________ Password: ____________

Your WAN IP Address: ____________ PPTP Server IP Address: ___________

Connection ID (if required): ____________

 PPPoE (PPPoE) Service Name: ____________

User Name: ____________ Password: ____________

Quick Start Overview

Hardware Installation...........................................................................................................................2

Setting Up Your Computer’s IP Address ............................................................................................5

Configuring Your ZyWALL .................................................................................................................7

ZyWALL 100

Hardware Installation

Rear Panel

LABEL DESCRIPTION

1. LAN 10/100M Connect a computer to this port with an Ethernet cable. This port is auto-negotiating (can

connect at 10 or 100Mbps). Push the UPLINK button in with a straight-through Ethernet cable or

have the UPLINK button out with a crossover Ethernet cable.

2. WAN 10/100M Connect your cable/DSL modem to this port with the cable that came with your modem.

3. POWER 100-

240VAC

Connect the included power cord (use only this cord) to this power socket.

After you’ve made the connections, connect the power cord to a power supply and push the power switch to the on position.

Look at the front panel LEDs.

CONSOLE Only connect this port if you want to configure the ZyWALL using the SMT via console port; see

your User’s Guide for details.

Connect the 9-pin male end of the console cable to the console port of the ZyWALL and the

other end to a serial port (COM1, COM2 or other COM port) on your computer. Your computer

should have a terminal emulation communications program (such as HyperTerminal) set to

VT100 terminal emulation, no parity, 8 data bits, 1 stop bit, no flow control and 9600 bps port

speed.

DIAL BACKUP

Only connect this port if you want to set up a backup WAN connection; see your User’s Guide for

details.

Connect the 9-pin female end of your modem or TA cable to this port and the other end to your

modem or TA.

DMZ 10/100M Connect publicly accessible servers (Web, FTP, etc.) to this port to make them visible to the

outside world. Use a crossover Ethernet cable to connect this port to a single computer.

For multiple computers, use a straight-through Ethernet cable to connect this port to a hub.

RESET You only need to use this button if you’ve forgotten the ZyWALL’s password. It returns the

ZyWALL to the factory defaults (password is 1234, LAN IP address 192.168.1.1, terminal

emulation settings as described above etc.; see your User’s Guide for details).

ZyWALL 100

LABEL DESCRIPTION

WIRELESS LAN Do not insert or remove a card with the ZyWALL turned on.

Turn off the ZyWALL before inserting or removing an 11 Mbps 802.11b-compliant wireless LAN

PCMCIA card (to avoid damage).

Slide the 64-pin connector end of the PCMCIA wireless LAN card into the slot as shown next.

Do not force, bend or twist the wireless LAN card.

The Front Panel LEDs

The PWR LED turns on when you connect the power. The SYS LED blinks while performing system testing

and then stays on if the testing is successful. The CON/AUX, LAN, WAN and WLAN LEDs turn on if they

are properly connected. Refer to the following table for more detailed LED descriptions.

ZyWALL 100

LED COLOR STATUS MEANING

On The ZyWALL is turned on.PWR Green

Off The ZyWALL is turned off.

SYS Green Off The ZyWALL is not ready or failed.

On The ZyWALL is ready and running.

Flashing The ZyWALL is rebooting.

Red On The power to the ZyWALL is too low.

WLAN Green Off The wireless LAN is not ready, or has failed.

On The wireless LAN is OK.

Flashing The wireless LAN is sending or receiving packets.

Green Off The 10M LAN is not connected.

On The ZyWALL is connected to a 10M LAN.

LAN 10M

Flashing The 10M LAN is sending or receiving packets.

Off The 100M LAN is not connected.

On The ZyWALL is connected to a 100Mbps LAN.

LAN 100M Orange

Flashing The 100M LAN is sending or receiving packets.

Green Off The 10M DMZ is not connected.

On The ZyWALL is connected to a 10M DMZ.

DMZ 10M

Flashing The 10M DMZ is sending/receiving packets.

Orange Off The 100M DMZ is not connected.

On The ZyWALL is connected to a 100Mbps DMZ.

DMZ 100M

Flashing The 100M DMZ is sending or receiving packets.

Off The 10M WAN link is not ready, or has failed.

On The 10M WAN link is OK.

WAN 10M Green

Flashing The 10M WAN link is sending or receiving packets.

Off The 100M WAN link is not ready, or has failed.

On The 100M WAN link is OK.

WAN 100M Orange

Flashing The 100M WAN link is sending or receiving packets.

Off The backup port is not connected.AUX LNK Green

On The backup port is connected.

ZyWALL 100

LED COLOR STATUS MEANING

Off The auxiliary port is not sending or receiving packets.AUX ACT Green

Flashing The auxiliary port is sending or receiving packets.

Setting Up Your Computer’s IP Address

Skip this section if your computer is already set up to accept a dynamic IP

address. This is the default for most new computers.

The ZyWALL is already set up to assign your computer an IP address. Use this section to set up your

computer to receive an IP address or assign it a static IP address in the 192.168.1.2 to 192.168.1.254 range

with a subnet mask of 255.255.255.0. This is necessary to ensure that your computer can communicate with

your ZyWALL.

Your computer must have an Ethernet card and TCP/IP installed. TCP/IP should already be installed on

computers using Windows NT/2000/XP, Macintosh OS 7 and later operating systems.

Windows 2000/NT/XP

1. In Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel.

2. In Windows XP, click Network Connections.

In Windows 2000/NT, click Network and Dial-up Connections.

3. Right-click Local Area Connection and then click Properties.

4. Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties.

ZyWALL 100

5. The Internet Protocol TCP/IP Properties screen opens (the

General tab in Windows XP).

- To have your computer assigned a dynamic IP address, click

Obtain an IP address automatically.

-To configure a static IP address, click Use the following IP

Address and fill in the IP address (choose one

from192.168.1.2 to 192.168.1.254), Subnet mask

(255.255.255.0), and Default gateway (192.168.1.1) fields.

6. Click Advanced. Remove any previously installed gateways in

the IP Settings tab and click OK to go back to the Internet

Protocol TCP/IP Properties screen.

7. Click Obtain DNS server address automatically if you do

not know your DNS server IP address(es).

If you know your DNS server IP address(es), click Use the

following DNS server addresses, and type them in the

Preferred DNS server and Alternate DNS server fields.

If you have more than two DNS servers, click Advanced, the

DNS tab and then configure them using Add.

8. Click OK to close the Internet Protocol (TCP/IP) Properties

window.

9. Click OK to close the Local Area Connection Properties

window.

Checking Your Computer’s IP Address

1. In the computer, click Start, (All) Programs, Accessories and then Command Prompt.

2. In the Command Prompt window, type "ipconfig" and then press ENTER. Your computer’s IP address must be in

the correct range (192.168.1.2 to 192.168.1.254) with subnet mask 255.255.255.0 in order to communicate with

the ZyWALL.

Refer to your User’s Guide for detailed IP address configuration for other Windows and Macintosh computer

operating systems.

ZyWALL 100

Configuring Your ZyWALL

Choose one of these methods to access and configure the ZyWALL. This Quick

Start Guide shows you how to use the web configurator wizard only. See your

User’s Guide for background information on all ZyWALL features and SMT

configuration. Click the web configurator online help for screen-specific web help.

 Web Configurator

 SMT (System Management Terminal). Access the SMT via:

o Console port using terminal emulation software

o LAN, WLAN or WAN using Telnet

Accessing Your ZyWALL Via Web Configurator

Step 1. Launch your web browser. Enter “192.168.1.1” as the web site address.

Step 2. The default password (“1234”) is already in the password field (in non-readable format). Click

default password in the password field.

Step 3. It is highly recommended you change the default password! Enter a new password, retype it to

confirm and click Apply; alternatively click Ignore to proceed to the main menu if you do not

want to change the password now.

Web site address.

Default password.

ZyWALL 100

Step 4. You should now see the web configurator MAIN MENU screen.

 Click WIZARD to begin a series of screens to help you configure your ZyWALL for the first time.

 Click a link under ADVANCED in the navigation panel to configure that ZyWALL feature.

 Click MAINTENANCE in the navigation panel to see ZyWALL performance statistics, upload

firmware and back up, restore or upload a configuration file.

 Click LOGOUT when you have finished a ZyWALL management session. The ZyWALL

automatically logs you out if it is left idle for five minutes; press ENTER to display the Login

screen again and then log back in. This idle timeout timer is one of the many ZyWALL features that

you may edit using the web configurator.

Using the Wizard to Configure for Internet Access

Change default password.

WIZARD

Navigation panel

LOGOUT

ZyWALL 100

Step 1. Click Wizard Setup in the main menu to display the first wizard screen.

System Name is for identification purposes.

Enter your computer's "Computer Name".

The Domain Name entry is what is propagated to

the DHCP clients on the LAN. If you leave this

blank, the domain name obtained by DHCP from

the ISP is used. Click Next to continue.

Step 2. The second wizard screen has three variations depending on what encapsulation type you use. Use

the information in Internet Account Information to fill in fields.

Choose Ethernet when the WAN port

is used as a regular Ethernet. Choose

from Standard or a RoadRunner

version. You’ll need User Name,

Password and Login Server IP

Address for some Roadrunner

versions.

Point-to-Point Protocol over Ethernet

(PPPoE) also functions as a dial-up

connection. Therefore you’ll also need

a username and password and

possibly the PPPoE service name.

Your ISP will give you all needed

information.

Choose PPTP if your service provider

uses a DSL terminator with PPTP

IP address in this case. You’ll also

need a login name, associated

password, the DSL terminator IP

address and possibly a connection ID.

Click Next to continue.

Step 3. Fill in the fields and click Finish to save and complete the wizard setup.

Otros manuales para Internet Security Gateway ZyWALL 100

Tabla de contenidos

Otros manuales de Puerta de ZyXEL Communications

ZyXEL Communications

ZyXEL Communications AMG1312-T Series Manual de usuario

ZyXEL Communications

ZyXEL Communications P-660HW-TX Manual

ZyXEL Communications

ZyXEL Communications N4100 Manual de usuario

ZyXEL Communications

ZyXEL Communications P-660HW-Tx v3 Series Manual de usuario

ZyXEL Communications

ZyXEL Communications AMG1202-T series Manual de usuario

ZyXEL Communications

ZyXEL Communications ZyWALL USG 2000 Manual

ZyXEL Communications

ZyXEL Communications P873HNUP - Manual de usuario

ZyXEL Communications

ZyXEL Communications ADSL2+ 4-port Gateway P-660H-D Series Manual de usuario

ZyXEL Communications

ZyXEL Communications P-660HN-F1A Manual de usuario

ZyXEL Communications

ZyXEL Communications EX5510-B0 Manual de usuario

ZyXEL Communications

ZyXEL Communications P-793H V2 - Manual

ZyXEL Communications

ZyXEL Communications P-660HN-T1H Manual de usuario

ZyXEL Communications

ZyXEL Communications VMG4381-B10A Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL USG 20W Manual de usuario

ZyXEL Communications

ZyXEL Communications P-793H 601156 Manual de usuario

ZyXEL Communications

ZyXEL Communications P-663HN-51 Manual

ZyXEL Communications

ZyXEL Communications ZYWALL USG 20 Manual de usuario

ZyXEL Communications

ZyXEL Communications VMG1312-B Series Manual de usuario

ZyXEL Communications

ZyXEL Communications P-660HN series Manual de usuario

ZyXEL Communications

ZyXEL Communications XMG3512-B10A Manual de usuario

ZyXEL Communications

ZyXEL Communications AMG1202-T10A Manual de usuario

ZyXEL Communications

ZyXEL Communications P-661HW-D Series Manual de usuario

ZyXEL Communications

ZyXEL Communications EMG2881-T20A Manual de usuario

ZyXEL Communications

ZyXEL Communications ZyXEL Prestige 310 Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario

RTA

RTA 460MCBC-N2E Hoja de especificaciones