Zte MF668+ Manual de usuario

Installation continued…

Click ‘Next’ to accept the default location or press ‘Change’ to specify your own path.The

installation takes a few minutes to complete.

Check your system requirements

USB port x 1 (USB 1.0 or 2.0*)1.

System Requirements:2.

PC – Windows 7,Vista, XP.a.

Mac - OSX 10.4.11 and above.b.

CPU 1GHz Pentium or above

Hard Disk 20GB or above

RAM 512M or above

Display 800 x 600 minimum

You need to have3. Administrator rights to install and run the software.

We suggest you switch off your anti-virus software before installing the USB modem.4.

In some cases protection software can prevent automatic installation. It is possible to

start the installation process manually by clicking the Autorun icon when it appears.

Tips

* USB 2.0 ports are preferred because they are much faster.

y

Identify the type of port on your PC and use version 2.0 ports.

y

Use the USB extender cable to obtain optimum reception.

y

There are 3 stages of installation:

y

Modem insertion, detection and installation of USB driver.i.

Install shield installation of Connection Manager software.ii.

Connection Manager launch and modem driver installation.iii.

Insert your SIM Card into the USB modem:1.

Open the modem back cover to access the SIM and MicroSD

yTM slot.

Insert the SIM card as shown with the gold contacts facing down and the bevelled

y

corner on the outside edge of the modem.

Push the SIM card in as far as it will go and replace the modem cover.

y

Connect the USB modem to your PC:2.

The computer must be switched ON and fully booted up.

y

Plug in the USB modem.The computer will start the Install Shield Wizard.

y

If your security settings prevent autorun then start the process manually.

y

Windows users:

¾Browse the Telecom Modem folder and double click Install.exe.

MAC users:

¾Open the CD-ROM,Telecom Modem, and double click Connection

Manager.

Follow the Install Shield prompts to complete the installation.

y

The Connection Manager software will start automatically and continue installing.

y

Installation Details3.

Screen shots are shown for Windows XP system.Other systems will follow a similar but

not necessarily identical process:

Click ‘Next’ to continue

MF668新西兰折页.indd 1 2009-9-24 11:47:59

Installation continued…

Press ‘Finish’ to complete - The Connection manager launches and installs the drivers:

Telecom Connection Manager - Press Connect to get on line…4.

When the installation is complete the Connection Manager will launch and continue

installing the drivers for a few minutes. After the device has nished initialising press

Connect to get on line.

LED status indication5.

LED Indicator Modem status

Red Ofine. Not registered on the network

Green solid Registered on the 2G network (roaming)

Green blinking Data active on the 2G network (roaming)

Blue solid Registered on the 3G network

Blue blinking Data active on the 3G network

Troubleshooting Tips6.

In the event of installation or connection issues try the following suggestions:

Install and test the modem in another computer1.

Check your SIM card is working in another device – eg mobile phone2.

Insert a known working SIM card into your modem3.

Conrm your account is active – contact your service provider4.

Uninstall the modem and re-install using Windows ‘Safe Mode’ – consult a PC5.

technician for help if required (PC only)

Advanced users can check Device Manager to make sure the drivers are installed6.

correctly.The full software installation is available on our website www.zte.co.nz

Using the Modem as a Mass Storage Device7.

You can insert a MicroSDTM memory card up to 8GB to use the modem as a mass storage

device.

Safely remove your modem from your computer.

y

Open the modem back cover to access the MicroSD

yTM slot.

There is a diagram showing the correct orientation of the MicroSD

yTM card printed on

the top of the MicroSDTM slot.

Check the correct orientation and carefully insert the MicroSD

yTM card.

Replace the modem cover and insert your device into your computer.

y

The MicroSD

yTM card will appear as an external drive on your computer system.

Always handle memory cards with care and avoid static discharge.

y

Safe removal of the modem from your computer8.

Whenever you need to remove the modem from your computer please close the Connection

Manager and use Safely Remove Hardware or Eject for MAC OS.

If you remove the device while the Connection Manager is still active it is possible to corrupt

the local Phonebook le.

Uninstall the modem software9.

Windows: Start > Programs >Telecom Connection Manager > Uninstall.

MAC OS X:Applications > Uninstall Telecom Connection Manager.

MF668新西兰折页.indd 2 2009-9-24 11:48:04

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario

Zoom

Zoom 1070 Series Manual de usuario

Aztech

Aztech HW831 Manual de usuario