Zonet ZFS3124 Manual de usuario
16 /24 port 10/100 Switch
Quick Installation Guide
16 / 24-port 10/100 Ethernet Switch
Introduction
The 16/24 port Ethernet Switch are designed to allow
simultaneous transmission of multiple packets via an internal
high-speed data channel. This means that it can partition a
network more efficiently than bridges or routers in most
environments .This 16/24 port Ethernet Switch is a highly
reliable network Switch and is the ideal device for bridging
Ethernet to Fast Ethernet workgroups or networks .Simple
and cost-effective, the 16/24 port Switch Ethernet supports
IEEE802.3 10Base-T Ethernet and IEEE802.3u 100Base-TX
Fast Ethernet.
The front panel of the 16/24 port Ethernet Switch provides
LEDs for Switch operation status and for troubleshooting.
These LEDs display the power status for the system and link
status speed ,collision and receives status for each port.
Package Contents
- 16 / 24 port 10 / 100 switch
- One Power Cord and Accessory
- One Quick Installation Guide(this guide)
- 2 pcs mount brackets
1-1 Introduction
16 / 24-port 10/100 Ethernet Switch
Spectification
Standard:
IEEE802.3 10Base-T Ethernet
IEEE802.3u 100Base-TX Fast Ethernet
Network Media:
100Base-TX - UTP/STP category 5 cable
10Base-T - UTP/STP category 3 or 5 cable
Connector: STP RJ-45 port for 10/100Mbps TX
LED indicators:
System - Power LED.
Individual port - link/activity and speed LEDs
Temperature: Operating
（
0 oC to 50 oC
）
Storage :
-20 oC to 70 oC
Humidity: Operating 10% to 90% RH
Storage :5% to 90% RH
Input Power Requirement: 100 - 240VAC, 50 - 60Hz,
Auto-sensing
Registrations:
FCC Part 15 Class A, CE
1-2 Spec
16 / 24-port 10/100 Ethernet Switch
LED Definition:
Please refer to the following table for LED definition
Front Panel
1. 16 Ports 10/100 Internal Power Switch
2. 24 Ports 10/100 Internal Power Switch
LED Status Operation
Power
Green Lit: Power is on
Link/act
Green
Lit: Indicates the adapter is connected
to swich correctly
Flash: the port is transmitting/receiving
data.
10/100
Green
Lit: 100M bps
Not lit: 10M bps
Rear Panel
1-3 LED Definition
16 / 24-port 10/100 Ethernet Switch
Hardware Installation
Place the 16/24 port Switch on a smooth surface
Connect the output of power cord to the AC-inlet of 16/24
port Switch.
Connect other IEEE802.3 compatible network
device(Hub ,Switch ,PC) to one port of the 16/24 port Switch
using Category 3/4/5 UTP/STP cabling.
Connect another IEEE802.3 compatible network device
(Hub , Switch ,PC) to another port of 16/24 port Switch by
following the same process as described in Step3.
Notice:
The cable distance between 16/24 port Switch and other
IEEE802.3 compatible network device should not exceed
100 meter.
Make sure the wiring is correct
It can be used Category 3/4/5 cable in 10 Mbps operation.
To reliably operate your network at 100Mbps, you must use
an Unshielded/Shielded Twisted-Pair (UTP/STP) Category 5
cable, or better Data Grade cabling. While a Category 3 or
4 cable may initially seem to work, it will soon cause data
loss.
All kinds of IEEE802.3 compatible network device (Hub ,
Switch ,PC)can connect to Switch by using straight-through
wires or crossover wires because of Switch's auto MDIX
function.
1-4 Installation
16 / 24-port 10/100 Ethernet Switch
Troubleshooting
If the 16/24 port Switch is not functioning properly, make sure
the 16/24 port Switch was set up according to instructions in
this manual.
The Power LED is not lit
Solution:
a. Check if the AC power cord is well connected. Try to
unplug and plug back the power cord to the LAN Switch or
try another power cord.
b. Check if the AC power source is in good condition.
The Link LED is not lit
Solution:
a. Make sure the Switch configuration is consistent with the
connecting device
c. Check the cable connections.
d. Make sure the cable distance between 16/24 port
Switch and other IEEE802.3 compatible network device
should not exceed 100 meter. Performance is bad
Solution:
a. Check the full duplex status of the Ethernet Switching. If
the Ethernet Switching is set to full duplex and the partner is
set to half duplex, then the performance will be poor.
b. Make sure the cable between the switch and other
IEEE802.3 compatible network device is Category 5 UTP at
100Mbps operation.
Some stations can not talk to other stations located on
the other port
Solution:
a. Check status of the LNK LED to make sure the link is
correct.
b. Make sure that the workstation's network configuration is
correct, modify the network configuration of workstation if
need.
c. Please reset the switch if need.
1-5 Trouble Shooting
Tabla de contenidos
Otros manuales de Cambiar de Zonet
Zonet
Zonet ZFS3308E Manual de usuario
Zonet
Zonet ZFS3015P Manual de operación
Zonet
Zonet ZFS3424E Manual de operación
Zonet
Zonet ZFS3224 Manual de usuario
Zonet
Zonet ZFS3224 Manual de operación
Zonet
Zonet ZFS3015P Manual de usuario
Zonet
Zonet KVM3008 Manual de usuario
Zonet
Zonet ZFS3228E Manual de usuario
Zonet
Zonet ZFS3224 Manual de usuario
Zonet
Zonet KVM3402 Manual de usuario
Zonet
Zonet KVM3402 Manual de usuario
Zonet
Zonet KVM3332 Manual de usuario
Zonet
Zonet ZUH2214L - QUICK INSTALLATION GUIDE REV 01 Manual de usuario
Zonet
Zonet ZFS3308E Manual de operación
Zonet
Zonet ZUH2000 - Manual de operación
Zonet
Zonet ZFS3018P Manual de operación
Zonet
Zonet ZFS3408EP Manual de operación
Zonet
Zonet KVM3002 Manual de usuario
Zonet
Zonet ZFS3015P Manual de usuario
Zonet
Zonet ZFS3416E Manual de operación
