ZOJE 5780BS Manual de usuario

 5780A

Z- - -91 172348 95

 00



HIGH SPEED COMPUTER CONTROLLED LOCKSTICH STRAIGHT BUTTON HOLING SEWING MACHINE- -





OPERTION MANUAL

PARTS BOOK

10051884

I．使用时的注意事项/IMPORTANT SAFETY INSTRUCTION

1）没有往油盒加油时，请绝对不要运转缝纫机。

2）缝制结束之后，请清扫旋梭、切刀部的灰尘和线绒。并确认油量是否充足。

3）使用启动踏板时，缝纫机启动后请把踏板返回到原来的位置否则会连续缝制。

4）本缝纫机装有安全开关，当缝纫机头放倒时，不让缝纫机运转。

要运转缝纫机时，请把缝纫机头正确地放置到台板上之后，再打开电源开关。

1 ) Never operate the machine unless the oiling tank has been properly lubricated.

2 ) Be sure to remove any dust from the hook or bobbin thread cutting knife section at the end of the

day, and check the amount of oil remaining.

3 ) Be sure to return the activating pedal to the home position after the machine has started to run.

4 ) A safety switch is installed so that this sewing machine can’t be operated in the state that the

machine head is tilted. When operating this sewing machine, turn the power switch ON after

setting the sewing machine to the bed base properly.

II．规格/ SPECIFICATIONS

1. 机种/Subclass

5780B 系列高速电子平头锁眼机有以下系列机型。

5780BSerise Computer-controlled high-speed lockstich Straight Button-holing Industrial Sewing

Machines has the subclass machines below.

机型

Subclass

套结宽幅(S)

Width of noose

切刀尺寸

Sise of cutter

缝制长度(B)

Sewing length

主要用途

Major application

5780BS 最大 6mm

The maximum 6mm

6.4~31.8mm

（1/4”~1-1/4）

最大 41mm

The maximum 41mm

缝制衬衣、衬衫、工作服、女装等棉布扣眼

Buttonholing of cloth such as men’s

shirts,blouses,work uniforms

5780BK 最大 6mm

The maximum 6mm

6.4~31.8mm

（1/4”~1-1/4）

最大 41mm

The maximum 41mm

T恤、 POLO 衫等针织料纽扣

T-shirt polo shirt knitted material

5780BL 最大 6mm

The maximum 6mm

6.4~31.8mm

（1/4”~1-1/4）

最大 120mm

The maximum 120mm

缝制衬衣、衬衫、工作服、女装等棉布纽扣

Buttonholing of cloth such as men’s

shirts,blouses,work uniforms

2. 规格/Specifications

名称规格

套结宽幅标准 5mm

缝纫速度标准 3600rpm（最高 4200rpm）

使用机针 DP×5 #11J ~ #14J

针杆行程 34.6mm

旋梭 DP 型全自动旋转供油旋梭

压脚上升量 6mm（可任意设定）最大 17mm（逆转抬压脚时）

抬压脚驱动方式脉冲马达式（1个踏板·2个踏板）

绕线功能机头内置式（在机器驱动中可绕线）

送布驱动方式脉冲马达式

摆针驱动方式脉冲马达式

切刀驱动方式脉冲马达式

面线张力机能电磁铁张力方式通过控制面板操作可对各部位进行数据设定（平行部、套件部张力）

缝迹形状角型、放射型、圆型（控制面板选择）等 30 种

记忆花样数 500 个花样

外形尺寸机床宽度 200mm、高度 360mm、长度 570mm

机头重量 55Kg

电源单向 220V

2. 规格/Specifications

Name of Controller specifications

Width 5mm（Min: 0.05mm）

Sewing Speed Standard 3600rpm Max 4200rpm

Needles DP×5 # 11J ~ # 14J

Stroke of Needle Bar 34.6mm

Shuttle Type DP, All-auto Rotation Oil-supply Shuttle

Presser Height 6mm (Customized Setting) Max 17mm(Reverse pressure lifting foot )

Winding Build-in Type (winding at machine running)

Cloth-feeding Driving Device Pulse Motor

Swing Needle Driving Pulse Motor

Knife Driving Device Pulse Motor

Upper-thread Tension Function Solenoid Tension Method User can set the data at control panel to adjust each

part (Parallel Part, Doubling Part Tension)

Stitch Form Angle, Radial, Round (Selected at Control Panel) and other 30 types

Patterns in Memory 500 Patterns

Size Width 200mm、Height 360mm、Length 570mm

Head Weight 55Kg

Motor used single phase 220V

3. 标准缝衣形状一览表/Standard sewing shape list

4. 构成

5780B 系列由以下部分所构成：

电源 ON/OFF 开关 Power ON/OFF switch

缝纫机机头（5780B 系列） Machine head （5780B Series）

操作板 Operation panel

电控箱 Control box

抬压脚、启动踏板 Presser lifting pedal and start pedal

线架装置 Thread stand device

III．安装/INSTALLATION

★危险：搬运缝纫机时，请至少 2人以上进行。

★WARNING：To prevent possible accidents caused by fall of the sewing machine,

perform the work by two persons or more when the machine is moved.

（1）板的安装/Set-up of the table

1）把控制箱、电源开关、固定到台板上。

2）用固定条把电源开关的电缆线固定起来。

3）把底座锁紧螺钉⑩（4个）穿过底座。

4）把减震橡胶安装到台板的底座固定孔（4处），然后固定底座。

5）把机头支撑杆固定到台板上。

6）把缝纫机主机放到台板上后，把踏板和踏板开关和附件的连接杆连接起来。

注意：请调整踏板位置，不让连接杆和控制箱相碰。

1) Securely install control box and power switch on table .

2) Securely fix the respective power cables of power switch .

3) Pass four bed base fixed screws (10)through bed base .

4) Set rubber cushions (5)to holes (6)and then fix on the base.

5) Fix head support bar on table .

6) After placing the sewing machine main unit on bed base ,connect pedal

Topedalswitch ,connecting rods which have been supplied as accessories .

►CAUTION ：Adjust the positions of the pedals so that connecting road and control

do not come in contact with each other.

（2）电源线的连接/Connecting the power cord

注意：在电压规格不同的状态下绝对不能使用。

►CAUTION ：Never use under the wrong voltage and phase.

（3）缝纫机主体的安装/ Installing the sewing machine main unit .

►注意：搬运缝纫机时，请一定 2人以上进行。

单相 220V 的连接/Connecting single phase 220V

►CAUTION ：To prevent possible accidents

caused by the tail of the sewing machine,

perform the work by two personal or more when

the machine is moved.

CAUTION ：Place hinge plates and shaft

bearings in two places on the head base and

fix the hinge plates to the machine head with

setscrew in two places.

►注意：不要把橡胶铰链和金属铰链安装

反了，否则放倒缝纫机时会有危险。

►注意：

1. 放倒缝纫机之前，请先确认台板上是否

装有机头支撑杆。

2. 为防止缝纫机突然倒下，请一定把缝纫

机放到水平的地方，再放倒缝纫机。

(4) 缝纫机的放倒方法/ Tilting the sewing machine head

★危险：放倒或抬起缝纫机时，请注意不要被缝纫机夹住手指。

为了防止突然的起动造成的事故，请关掉电源之后再进行操作。

放倒缝纫机时，请轻轻地放倒，让缝纫机被机头支撑杆支撑住。

★WARNING : When tilting /raising the sewing machine head, perform the work so as not to allow

your fingers to be caught in the machine, to avoid possible accidents caused by abrupt start of the

machine, turn OFF the power to the machine before starting the work.

When tilting the sewing machine head, tilt quietly the sewing machine until head supper bar comes in.

►CAUTION：

1.Make sure that sewing machine head support bar

is placed on the table before tilting the sewing machine

2.To protect-fall-down, be sure to tilt the sewing

machine in a level place.

（5）安全开关的连接/Connecting the safety switch connector

（6）挡油板的安装/Installing the hook oil shield plate

Install hook oil shield plate onto bed base with setscrew .

注意：放倒缝纫机或抬起缝

纫机时，请注意不要碰到挡油

板。

用固定螺钉把挡油板安装到底座上。

打开机头后罩，把安全开关的

插口连接到机头后端电路板

JP7 上，再重新罩上后罩。

After open the machine cover,

connecting safety switch connector

with connect located on the

PCB which is on the back of the

machine.

►CAUTION ：Fixes the sewing

machine so that it does not come in

contact with kook oil shield plate

when raising/tilting the sewing

machine.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de coser de ZOJE

ZOJE

ZOJE ZJ1900DSS-3-04-V4-TP Manual de usuario

ZOJE

ZOJE WR580 Manual de usuario

ZOJE

ZOJE ZJ-M6-GS800-SF-V2 Manual de usuario

ZOJE

ZOJE ZN90 Manual de usuario

ZOJE

ZOJE ZJ-AM-5775AH Manual de usuario

ZOJE

ZOJE ZJ9600 Manual de usuario

ZOJE

ZOJE ZJ20U93 Manual de usuario

ZOJE

ZOJE B9500 Manual de usuario

ZOJE

ZOJE ZJ1900DSS Manual de usuario

ZOJE

ZOJE ZJ8700 Manual de usuario

ZOJE

ZOJE ZJ5300 Manual de usuario

ZOJE

ZOJE ZJ927 Series Manual de usuario

ZOJE

ZOJE YXP-3 Manual de usuario

ZOJE

ZOJE QD2622 Series Manual de usuario

ZOJE

ZOJE ZJ24028-1 Manual de usuario

ZOJE

ZOJE ZJ9610 Manual de usuario

ZOJE

ZOJE ZJ2628-1 Manual de usuario

ZOJE

ZOJE ZJW662 Manual de usuario

ZOJE

ZOJE 9610 Manual de usuario

ZOJE

ZOJE ZJ9700 Manual de usuario

ZOJE

ZOJE ZJ781-BD Manual de usuario

ZOJE

ZOJE ZJ5600N Manual de usuario

ZOJE

ZOJE ZJ200 Manual de usuario

ZOJE

ZOJE ZJ-M3-S500-SF-V2 Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario