Zodiac Edenpac 2 Manual de usuario

CONTENTS

1 General.................................................. 2

1.1 General terms of delivery..............................2

1.2 Voltage.......................................................... 2

1.3 Water treatment.............................................2

2 Description............................................ 2

2.1 Presentation...................................................2

2.1.1 Edenpac 2, 3, 4 and 5

2.1.2 Edenpac 6

2.2 Dimensional characteristics...........................5

2.2.1 Edenpac 2,3, 4 and 5

2.2.2 Edenpac 6

3 Installation............................................ 7

4 Connections .......................................... 9

4.1 Access to the electrical card .............................9

4.1.1 Edenpac with single fan

4.1.2 Edenpac with double fan

4.2 Hydraulic connections...................................... 10

4.3 Electric connection...........................................11

5 Regulator operation............................. 12

5.1 Presentation ......................................................12

5.2 Setting the target temperature...........................12

6 Starting up............................................ 13

6.1 Check................................................................13

6.2 Start up the heat pump......................................14

6.3 Checking...........................................................14

6.4 Fault and state display ......................................15

6.5 Winter storage ..................................................16

7 Maintenance instructions.................... 16

8 Recycling the product.......................... 16

9 Electrical diagrams.............................. 17

9.1 Electrical diagram of connection

Interface card.................................................... 17

9.2 Electrical diagram EdenPAC single-phase....... 18

9.3 Electrical diagram EdenPAC three-phase......... 19

1. GENERAL

1.1 General terms of delivery

Any equipment, even CARRIAGE and PACKING FREE, travel at the consignee’s risk. The consignee shall make

reserves in writing on the CARRIER’S delivery bill if he notes damage caused during transport. (Confirmation to be sent

to the CARRIER within 48 hours by registered mail with acknowledgement of receipt).

Reminder: The unit must be shipped and stored in the upright position on a pallet and in the original packaging. In the contrary

case, place the unit in the vertical position on the pallet and check its global state (in case of doubt regarding the unit’s good state of

operation establish reserves in writing with the carrier).

-Under no circumstances may the heat pump be operated immediately if it was placed horizontally.

Wait at least 12 hours before operating the pump -

1.2 Voltage

Prior to any operation, check that the voltage on the name plate of the appliance corresponds to the mains voltage

provided on site.

1.3 Water treatment

In order to use our appliances under the best conditions, the following parameters must be respected: free chlorine: max.

2.5 mg/l, total bromine: max. 5.5 mg/l, pH between 6.9 and 8.0. If chemical or electrophysical disinfection systems are

used, the installer and user must contact the supplier to ensure they are compatible with our materials. These systems must

be installed after the heating system.

2. DESCRIPTION

2.1 Presentation

Contents after unpacking:

The unit with its instructions, warranty card

Note: inside the appliance you will find a sachet of accessories. To extract it, see paragraph 4.1 of these instructions.

Content of sachet:

two half-union connectors Ø50 with strap + two sealing rings - four silent blocks 

rooved elbow union .- a

lastic ca

- four anchor bolts and dowels 

(

onl

lied wi

h double fan uni

)

+ +











Must be installed

with a double fan

machine

2.1.1 Edenpac 2, 3, 4 and 5

1Front panel with polypropylene grid.

2Motor fan unit.

3Access flap to digital regulator 3a

(Euro α FK) & and pressure gauge ″water flow″3b

(measures the refrigerant pressure in the HP circuit

and is used to regulate the compressor & fan water

flow-rate ON).

4Electronic card.

5HP pressure switch.

6Flow controller.

7TITANIUM condenser unit.

8Regulator sensor.

9LP pressure switch.

Cased SCROLL compressor

11 Arched ‘flat fin’ unit cooler.

12 Anti-frost sensor.

13 Fastening plates

(with silent blocks).

14 Pool inlet water connection

(40/49 male screw fastening).

15 Packing gland (and/or cable inlet).

16 Pool outlet water connection

(40/49 male screw fastening).

17 Removable polypropylene panel

to access the technical compartment.

18 Closing snap clips.

3456

9

Attention! never use the panel reinforcement as a

load-bearing support .

2.1.2 Edenpac 6

11 Arched ‘flat fin’ unit cooler.

12 Anti-frost sensor (NV).

13 Fastening plates.

14 Pool inlet water connection

(40/49 male screw fastening) (NV).

15 Packing gland (and/or cable inlet)

(NV).

16 Pool outlet water connection

(40/49 male screw fastening) (NV).

17 Removable polypropylene panel

to access the technical compartment.

18 Closing snap clips.

NV: Not Visible on photos but located

at the back of the unit



1Top and bottom panels with polypropylene grid.

2Motor fan unit.

3Access flap to digital regulator 3a

(Euro α FK) & and pressure gauge ″water flow″3b

(measures the refrigerant pressure in the HP circuit

and is used to regulate the compressor & fan water

flow-rate ON).

4Electronic card.

5HP pressure switch.

6Flow controller.

7TITANIUM condenser unit.

8Regulator sensor.

9LP pressure switch.

Cased SCROLL compressor

Attention! never use the panel reinforcement as a

load-bearing support .

2.2 Dimensional characteristics

2.2.1 Edenpac 2, 3, 4 and 5

Dimensions of the appliance with packaging (in mm) :

Weight of Edenpac 2 with packaging : ≅98 kg

Weight of Edenpac 3 with packaging : ≅101 kg

Weight of Edenpac 4 - 5 with packaging : ≅110 kg

1275

480

870

To be transported upright in its original

packaging close to the installation site.

2.2.2 Edenpac 6

Dimensions of the appliance with packaging (in mm) :

Weight of Edenpac 6 with packaging: ≅145 kg

3. INSTALLATION

Tools required for installation :

-1 set of flat head screwdrivers

-1 set of crosshead screwdrivers

-1 cutter

-1 wire stripper

-1 pipe or round head spanner 13

-1 ratchet spanner

-1 pliers

-2 straps (for handling)

Choose the appliance installation site according to the following criteria:

• the appliance must be installed outdoors

• the clearance around the appliance must be respected

(see minimum dimensions on the drawings below) to avoid recycling of cold air produced.

vers égout

Dense obstacle (hedge, wall, fencing).

1370



To be transported upright in its original

packaging close to the installation site.

1275

480

• the installation must be simple and allow for easy maintenance interventions.

• the appliance must be installed on a solid base (fastening centre distance 810 x 370) and protected against

flooding (using a « concrete » base with drain facility for condensation or installation of an additional condensation

evacuation kit placed at your disposal in the accessories sachet). The silent blocks supplied must be used, paying

attention not to compress them too much when tightening the fastening screws .

• the appliance must be level to allow for the gravitational evacuation of |possiblecondensation produced during

operation.

• the blower must not be directed towards surrounding windows.

• vibrations and noise must not be transmitted to a building close by.

• the heat pump must be installed at a minimum distance from the end of the pool, as defined by the applicable

national electrical standards. In France, standard NF C 15 100 (section 702) specifies that the appliance must not be

installed less than 2 metres from the pool or water reserve, but may be installed between 2 and 2.35 metres if there

are not water jets. In the contrary case, respect a minimum distance of 3.5 metres.

Attention ! :

• Do not lift the appliance by picking it up at the front and/or the water inlet/outlet points. Use 2 lifting slings (not

supplied) placed on either side of the appliance (see drawing below). The handle on the right side may be used only to help

with the final positioning of the appliance.

• Do not install the heat pump close to an inflammable gas source.

• Do not install the heat pump close to a road or path to protect the appliance against mud splashing.

• Avoid places that are subject to strong winds, in particular if the wind blows against the appliance’s air outlet.

• The installation as well as electric and hydraulic connections must be carried out in compliance with applicable standards, in

particular standard NF C 15 100 for France (equivalent to CE I 364) .

• Keep the appliance out of reach of children.

To use the additional condensation evacuation

kit:

- Use the grooved elbow union and cap.

- The tank is equipped with two evacuation holes, one for the

cap and the other for the grooved elbow union (their

position is interchangeable).

Note:To facilitate installation raise the unit 100 mm above

the ground with the additional blocks made of a hard,

water-resistant material (not supplied).





Slings



4. CONNECTIONS

4.1 Access to the electric card

4.1.1 Edenpac with single fan

Turn the clips ¼ turn clockwise on the front panel 1using a flat head screwdriver.

Unscrew the 2 screws 2and 3on the right side using a cross head screwdriver.

Slide the entire front panel forward and then down.

4.1.2 Edenpac with double fan

Turn the 2 clips 1a and 1b in the front ¼ turn clockwise using a flat head screwdriver.

Unscrew the 2 screws 2and 3on the right side using a cross head screwdriver.

Slide the entire front panel forward and then down.

4.2 Hydraulic connections

Connect the appliance’s PVC Ø 50 hose water inlet and outlet (according to symbols) to the removable fittings provided

with the heat pump. See symbols : for inlet and for outlet.

Connection is established with a by-pass on the pool filtration circuit after the filter and before the water treatment facility

(see diagrams below).

- Hydraulic circuit test pressure: 3 bar - Hydraulic circuit operating pressure: 1.5 bar

Edenpac 2,3,4 and 5 : - Average water flow 5 to 6.5 m3/h- pressure drop 1.3 to 1.7 mCE (0.13 to 0.17 bar) –

Edenpac 6 : - Average water flow 7.5 m3/h- pressure drop 1.1 mCE (0.11 bar) –

V1-V2-V3 : By-pass valve

V5-V4 : Regulator valve*

* Recommended to facilitate

adjustment close to the unit.

V1-V2-V3 : By-pass valve

V5-V4 : Regulator valve*

* Recommended to facilitate

adjustment close to the machine.

V2 V3

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de Zodiac

Zodiac

Zodiac Z700 DUO Series Manual de usuario

Zodiac

Zodiac ZS500 Manual de usuario

Zodiac

Zodiac Z550iQ Manual de usuario

Zodiac

Zodiac Z200 Guía

Zodiac

Zodiac ZHP-3216-TI Manual de usuario

Zodiac

Zodiac Z250 Manual de usuario

Zodiac

Zodiac Edenpac 1 Manual de usuario

Zodiac

Zodiac ZS500 MD5 Manual de usuario

Zodiac

Zodiac PW-5m Manual de usuario

Zodiac

Zodiac AquaLink Z350iQ Manual de usuario

Zodiac

Zodiac Z550iQ Manual de usuario

Zodiac

Zodiac Pac Alpha 5M Manual de usuario

Zodiac

Zodiac Z250 MD3 Manual de usuario

Zodiac

Zodiac Z350iQ MD4 Manual de usuario

Zodiac

Zodiac Z400 iQ Manual de usuario

Zodiac

Zodiac Edenpac 4D Manual de usuario

Zodiac

Zodiac ZS500 Manual de usuario

Zodiac

Zodiac Z200 Manual de usuario

Zodiac

Zodiac PW-5m Manual de usuario

Zodiac

Zodiac PW-5m Manual de usuario

Zodiac

Zodiac PX 50 Manual de usuario

Zodiac

Zodiac PX50 MD12 Manual de usuario

Zodiac

Zodiac Jandy Pro Series JE1500T Manual de usuario

Zodiac

Zodiac POWER FORCE Series Manual de usuario

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario