Zmotion ZMC303 Manual de usuario
ZMC303 Hardware Manual
Version 1.3
ZMC303 Hardware Manual Version1.3
1
Copyright statement
This manual is copyrighted by Shenzhen Technology Co., Ltd.,
without the written permission of the Zmotion Technology, no
person shall reproduce, translate and copy any content in this manual.
ZMC controller software involved in details as well as the
introduction and routines of each instruction, please refer to ZBASIC
software manual.
Information contained in this manual is only for reference. Due to
improvements in design and functions and other aspects, Zmotion
Technology reserves the final interpretation! Subject to change without
notice!
Pay attention to safety when debug the machine! Be sure to
design effective safety devices in the machine, and to add
error handling procedures in software. Zmotion has no
obligation or responsibility for the loss.
ZMC303 Hardware Manual Version1.3
2
Contents
ZMC303 Hardware Manual..............................................................................................................1
Chapter I Introduction Of Controllers...............................................................................................1
1.1 Connection Configuration...................................................................................................1
1.2 Installation And Programming............................................................................................2
1.3 Features...............................................................................................................................3
Chapter II Hardware Description......................................................................................................4
2.1 ZMC303 Series Controller..................................................................................................4
2.1.1 Order Information ....................................................................................................5
2.2 Wiring Reference ................................................................................................................6
2.2.1 Power Interface........................................................................................................7
2.2.2 Communication Interface.........................................................................................8
2.2.3 RS232 Interface........................................................................................................8
2.2.4 General Input..........................................................................................................10
2.2.4.1 Input 0-7....................................................................................................10
2.2.4.2 Input 8-15..................................................................................................11
2.2.4.3 Input 16-23................................................................................................11
2.2.5 General Output.......................................................................................................12
2.2.6AD/DA Signal........................................................................................................13
2.2.7 USB Drive..............................................................................................................13
2.2.8Axis Interface.........................................................................................................13
2.2.8.1 Axis 0-2.....................................................................................................13
2.2.9Axis Wiring Reference...........................................................................................15
2.2.9.1 Wiring Reference for Low-speed Differential Pulse and Encoder Axis....15
2.2.9.2 Wiring Reference for High-speed Differential Pulse or EncoderAxis......17
2.2.9.3 Wiring Reference for Encoder...................................................................18
Chapter III Expansion Module........................................................................................................20
3.1 Wiring Reference For CAN, Input, Output and Power.....................................................20
ZMC303 Hardware Manual Version1.3
3
Chapter IV Common Problems.......................................................................................................21
Chapter V Hardware Installation.....................................................................................................23
5.1 ZMC303 Installation Size.................................................................................................23
ZMC303 Hardware Manual Version1.3
1
Chapter I Introduction of Controllers
ZMC is the abbreviation of network motion controller model launched by ZMOTION
technology.
ZMC303 series controller supports linear interpolation of up to 10 axis, interpolation
of circular, spherical, electronic cam, electronic gear, synchronous following, virtual
axis setting etc. Real-time motion control can be realized by using optimized network
communication protocol.
One Computer can link with up to 256 ZMC controllers.
1.1 Connection Configuration
Typical Connection Configuration
The controller supports ETHERNET, USB, CAN, 485 and other communication
interfaces. Input, output or axis can be extended through CAN bus. (Resistance of 120
Ω is required between CANL and CANH).
ZMC controller supports data saving or reading through USB Drive. (Except for
ZMC00X series)
ZMC303 Hardware Manual Version1.3
2
1.2Installation And Programming
ZDEVELOP Development Environment
Debugging of ZMC controller is available in ZDEVELOP. Since ZDEVELOP is a
very convenient programming, compiling and debugging environment.
Communication between controller and ZDEVELOP can be built through serial port,
485, USB or Ethernet.
Application can be developed in PC by using software such as VC.VB, VS. C++
Builder, C# etc. But dynamic library zmotion.dll is needed when operating procedure
in PC. ZDEVELOP can be connected to the controller when debugging the PC
based procedure in order to detect more information.
ZMC303 Hardware Manual Version1.3
3
1.3 Features
⚫Motion control of up to 10 axes.
⚫Pulse output mode: direction / pulse or double pulse.
⚫Encoder position measurement is supported and can be configured as hand wheel
input mode.
⚫Maximum pulse frequency output of each axis: 10MHZ.
⚫Maximum inputs or outputs can reach 512 through CAN bus.
⚫The positive or negative limit signal / origin signal of axis can be configured to
any inputs.
⚫The output current can reach 300mA, which can directly drive some kinds of
solenoid valves.
⚫Interfaces: USB drive, RS485, RS422 and ETHERNET etc.
⚫Linear interpolation of up to 10 axes, interpolation of random, spherical and
helical.
⚫Electronic cam, electronic gear, position latch synchronous follow, virtual axis
etc.
⚫Pulse closed loop, pitch compensation and other functions.
⚫Multi-file and multi-task programming in ZBasic.
⚫A variety of program encryption methods to protect the intellectual property
rights of customers.
⚫Power failure detection and power failure storage.
ZMC303 Hardware Manual Version1.3
4
Chapter II Hardware Description
2.1 ZMC303 Series Controller
ZMC303
Axes
3
Maximum extended axes
10
Type of basic axes
Pulse output, with encoder.
Internal IO
24+3 inputs, 8+3 outputs, (8 channels with overcurrent
protection)
Maximum extended IO
512 inputs and 512 outputs
PWM
2(output frequency 1M)
Internal ADDA
2 ADs, 2DAs. (0-10V)
Maximum extend ADDA
256 ADs, 128 DAs
Pulse bits
32
Encoder bits
32
Speed/Acceleration bit
32
Max pulse frequency
10Mhz
Axis motion buffer
128
Array size
32000
Procedure size
300KByte
Flash size
128MByte
Power input
24V DC (power consumption is within 10W, fan cooling is
not needed), IO consumption is not included.
Communication
RS232, RS485, RS422, ETHERNET, USB drive, CAN
Size
205*134mm
ZMC303 Hardware Manual Version1.3
5
Configure axis 6 to 8 as encoder type, then these axes will be mapped to axis 0-2
as encoder axes, which will get encoder feedback of axis 0-2.
Axis 4 can be configured as an encoder when using IN0-2. (It must be 24V) It
can also support 24V hand wheel.
2.1.1 Order Information
Model
Specification Description
ZMC303
3 axes, Point to point, Interpolation of linear, interpolation of circular,
spherical and helical etc. electronic cam, continuous motion, Robotic
Instruction.
ZMC303 Hardware Manual Version1.3
6
2.2 Wiring Reference
➢There are 3 basic axes, 3 5V encoders and 1 24V encoder in ZMC303, it supports
up to 10 virtual axes, and can be extended axes through expansion module.
➢There are 24 general inputs, 8 outputs (additional 1 input and 1 output), 2 0-10V
AD and 2 0-10V DA, 1 RS232, 1 RS485 1 USB drive and one Ethernet.
➢1 CAN bus, which is used to link with expansion modules through ZCAN
communication protocol.
Otros manuales para ZMC303
1
Tabla de contenidos
Otros manuales de Hardware de computadora de Zmotion
Zmotion
Zmotion ECI2608 Manual de usuario
Zmotion
Zmotion XPCI1400 Manual de usuario
Zmotion
Zmotion EIO24088 Manual de usuario
Zmotion
Zmotion XPCIE1028 Manual de usuario
Zmotion
Zmotion ZAIO Manual de usuario
Zmotion
Zmotion XPCI1C00 Manual de usuario
Zmotion
Zmotion ZMIO300 Series Manual de usuario
Zmotion
Zmotion EIO16084 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
