ZKTeco QR50 Manual de usuario

QR50 QR Code Access Control

Reader

User Manual

Version：V1.0 Date：2021.04.01

Important statement

Thank you for choosing this product. Before use, please read this installation guide and

instruction manual (hereinafter referred to as the instruction manual) carefully to ensure that the

product is used correctly, has a good use effect and verification speed, and avoids unnecessary

damage to the product.

Without the written consent of the company, no one may copy or disseminate any content of

this manual in any form.

Disclaimer

Due to the continuous update of the product, the company cannot promise that the

information is consistent with the actual product, and it is not responsible for any disputes caused

by the inconsistency of the actual technical parameters with this information. Any changes will

not be notified in advance. The company reserves the right of final modification and

interpretation.

Revision Record

Version

Revision Content

Revision Date

V1.0

All New

2021/04/01

3 
 
Contents 
IMPORTANT STATEMENT ......................................................................................................................... 1 
REVISION RECORD..................................................................................................................................... 2 
CONTENTS..................................................................................................................................................... 3 
1、INSTALL EQUIPMENT .......................................................................................................................... 4 
2、PRODUCT INTRODUCTIONS .............................................................................................................. 5 
3、WIRING INSTRUCTIONS...................................................................................................................... 5 
3.1 WIRING DEFINITION .................................................................................................................................. 5 
3.2 OPERATING INSTRUCTIONS ....................................................................................................................... 5 
4、OPERATION AND SETTING OF CARD READER ............................................................................ 7 
4.1 ONE-KEY CONFIGURATION........................................................................................................................ 7 
4.2 BASIC OPERATION OF CARD READER....................................................................................................... 9 
4.3 WIEGAND SETTING................................................................................................................................... 12 
4.4 READ CARD SETTING................................................................................................................................ 13 
4.5 READER OPERATION................................................................................................................................. 14 
4.6 UPGRADE FIRMWARE............................................................................................................................... 14 

1、Install Equipment

Installation notes: In order to ensure the normal use of the equipment, users are requested to strictly follow the

installation instructions

Buy the standard type 86 dark (bottom) bo

xfrom the market, and the installation hole

distance is 60mm or 66mm. The installer di

gs ahole on the wall surface according to t

he length, width and depth of the standard

86-type dark (bottom) box to place the dar

k(bottom) box and fix it with cement sand

60mm or

66mm

Remove the cover (with panel) from

the device. It is necessary to gently

remove the panel from the USB port

side to avoid damage to the LED light

when removing it

Face shell (with panel)

When installing, connect the wire and

debug it, then put the device into the

86-type concealed (bottom) box as shown

in the figure, and fix the device with two

M4*15PB mechanical screws. Pay attention

to the downwards on the device with the

boss.

The device has this boss facing

downwards during installation

First find the right alignment point, and then

buckle the shell (with panel) into the device

(as shown in the figure), pay attention to the

assembly direction during installation and

check whether the printing on the rear panel

is upright.

The panel is printed upright, and the notch under the

shell is aligned with the boss under the device

2、Product Introductions

The QR code access control card reader is a new generation of smart access control card reader

developed by our company. The product has high-end appearance, fast scanning speed, high

recognition rate, strong compatibility, and can be connected to any access control controller that

supports Wiegand input. It adapts to various application scenarios, supports identification of RFID

radio frequency cards and QR codes, and can be used in community management, visitor

management, hotel management, unmanned supermarkets and other fields.

The characteristics of the QR code reader as followed：

⚫Development of new QR code access control technology.

⚫The card reader comes with a card reader antenna, the working frequency is 125KHz.

⚫Support ID，MF，CPU，NFC (analog card)，Desfire EV1，and QR code.

⚫Support Wiegand，RS485，USB (upgrade use).

3、Wiring Instructions

3.1 Wiring Definition

From the reverse side (pictured above) from left to right：

DC(+12V)

GND

485A

485B

WG0

WG1

VCC

GND

RS485 Port

Wiegand Port

3.2 Operating Instructions

Note: During use, please follow the wiring definition of the QR code reader to connect with other devices. In

addition, what is mentioned below is only part of the wiring between the QR code reader and the controller,

and does not represent all the wiring definitions of the controller. Please refer to the actual controller wiring

definitions.。

1.Wiegand or RS485 Communication

①First, connect the QR code reader to the controller via Wiegand or RS485, and then connect

the +12V power supply.

The QR code reader does not need to be connected to the lock body when it is used as a reader.

The controller in the figure only lists part of the wiring. In addition, there are many ways

to connect between the machines. Refer to the following figure for the common connection

methods of Wiegand or RS485：

②Then, put the card or QR code (paper, electronic, mobile phone) into the recognition range

of the card reader, and the card reader will automatically obtain and transmit the information

carried by the card or QR code to the controller.

2.USB Communication

①First, connect the QR code reader to the PC through the USB interface.

②Then, open the "HID keyboard" in the DEMO software settings, and then put the card or

QR code (paper, electronic, mobile phone) into the recognition range of the card reader, the

card reader will automatically obtain the information carried by the card or QR code And

transmit to the PC terminal, can demonstrate through the text document.

4、Operation and Setting of Card Reader

Introduce how to configure the card reader through Demo software.

4.1 One-key Configuration

Operation steps

1. Connect the QR code reader to the computer with a USB cable, open the Demo software, select

the USB port, click "OK", the connection is successful. (Note: If you choose serial port

connection, the default baud rate is 115200）

Note：Support Connection Configuration tool via USB and serial port。

USB：Connect to the configuration tool via USB communication。

COM：Connect the configuration tool through RS485 communication。

2. Successfully connected, click download in the download configuration area below。

3. Prompt that the download configuration is complete, and the QR code reader configuration

can be completed with one click, the operation is simple。

-----The End

4.2 Basic Operation of Card Reader

Operation Steps

1. If the user needs to set the parameters of the QR code reader by himself, open the Demo

software, after the connection is successful, enter the QR50 advanced settings page in

the upper right corner of the page。

Otros manuales para QR50

Tabla de contenidos

Otros manuales de Lector de tarjetas de ZKTeco

ZKTeco

ZKTeco UHF10F Pro Reader Manual de usuario

ZKTeco

ZKTeco inBIO260 Guía

ZKTeco

ZKTeco KR500-BT Manual de usuario

ZKTeco

ZKTeco Bio30R Manual de usuario

ZKTeco

ZKTeco KR500 Manual de usuario

ZKTeco

ZKTeco UHF5 Pro Manual de usuario

ZKTeco

ZKTeco BR1200 Series Manual de usuario

ZKTeco

ZKTeco QR600 Series Manual de usuario

ZKTeco

ZKTeco UR20RWF Manual de usuario

Manuales populares de Lector de tarjetas de otras marcas

Lindy

Lindy 43185 Manual de usuario

Lindy

Lindy 43185 Manual de usuario

ViziT

ViziT RD-4F Manual de usuario

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manual de usuario

AVID ID

AVID ID AVID1043 Manual de usuario

Conrad

Conrad PCMCIA Manual de usuario

Rosslare

Rosslare DR-6255 Manual de usuario

Lindy

Lindy 51541 Manual de usuario

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manual de usuario

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manual de usuario

ACS

ACS ACR122L Manual de usuario

Secukey

Secukey S2-MF Manual de usuario

Elecom

Elecom MR-SMC07 series Manual de usuario

Alien

Alien ALR-9800 Manual de usuario

ACS

ACS ACR310 Manual de usuario

Datamars

Datamars R-IN1300 MID Manual de usuario

Alarm Lock

Alarm Lock AL-PRE2 Manual de usuario

xpr

xpr B100PROX-AH Guía del usuario