Ziton ZP3-ECU Guía
ZP3-ECU Extinguishing
Control Unit Installation
and Commissioning
Manual
P/N 503-0800ZE-I-05 • ISS 31JUL23
Copyright
©
2023 Carrier. All rights reserved.
Trademarks and
patents
The
ZP3-ECU name and logo are trademarks of Carrier.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
Carrier
Manufacturing Poland Spółka Z o.o.
Ul. Kolejowa 24. 39
-100 Ropczyce, Poland.
Authorized EU manufacturing representative:
Carrier Fire & Security B.V.,
Kelvinstraat 7, 6003 DH Weert,
Netherlands.
Revision
05
Conformity
2014/30/EU (EMC Directive). Hereby,
Carrier declares that this
device is in compliance with the essential requirements and other
relevant provisions of Directive 2014/30/EU.
2012/19/EU (WEEE Directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the Eu
ropean
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
recycleth
is.info.
2006/66/EC (Battery Directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbo
l, which may
include lettering to indicate cadmium (Cd), lead (Pb), or
mercury
(Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see:
recyc
lethis.info.
Contact information
and product
documentation
For contact information or to download the latest product
documentation, visit
firesecurityproducts.com.
ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual i
Content
Important information ii
Safety issues and limitations iv
Chapter 1 System wiring 1
Wiring standards 2
Wiring connections 3
Chapter 2 Installation 13
Installation location 14
Installation procedure 15
Chapter 3 Commissioning 17
Introduction 18
Programming the ECU 22
Tests 27
Chapter 4 Technical specifications 28
ii ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual
Important information
This is the installation manual for the ZP3-ECU Extinguishing Control Unit (ECU).
Read these instructions and all related documentation entirely before installing or
operating this product.
Product compatibility
The ZP3-ECU is compatible for use with the following addressable fire alarm
control panels running the Ziton protocol:
• ZP3 Series
• ZP2 Series
• ZP2-A Series
Limitation of liability
To the maximum extent permitted by applicable law, in no event will Carrier be
liable for any lost profits or business opportunities, loss of use, business
interruption, loss of data, or any other indirect, special, incidental, or
consequential damages under any theory of liability, whether based in contract,
tort, negligence, product liability, or otherwise. Because some jurisdictions do not
allow the exclusion or limitation of liability for consequential or incidental
damages the preceding limitation may not apply to you. In any event the total
liability of Carrier shall not exceed the purchase price of the product. The
foregoing limitation will apply to the maximum extent permitted by applicable law,
regardless of whether Carrier has been advised of the possibility of such
damages and regardless of whether any remedy fails of its essential purpose.
Installation in accordance with this manual, applicable codes, and the instructions
of the authority having jurisdiction is mandatory.
While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, Carrier assumes no responsibility for errors
or omissions.
ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual iii
Product warnings and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE TO AND INSTALLATION BY
QUALIFIED PROFESSIONALS. CARRIER FIRE & SECURITY B.V. CANNOT
PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER” OR “AUTHORIZED
RESELLER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY
INSTALL FIRE AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and product safety information,
please check https://firesecurityproducts.com/policy/product-warning/ or scan the
QR code:
Advisory messages
Advisory messages alert you to conditions or practices that can cause unwanted
results. The advisory messages used in this document are shown and described
below.
WARNING: Warning messages advise you of hazards that could result in injury
or loss of life. They tell you which actions to take or to avoid in order to prevent
the injury or loss of life.
Caution: Caution messages advise you of possible equipment damage. They tell
you which actions to take or to avoid in order to prevent the damage.
Note: Note messages advise you of the possible loss of time or effort. They
describe how to avoid the loss. Notes are also used to point out important
information that you should read.
iv ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual
Safety issues and limitations
Installation criteria
Do not attempt to install, service, or operate the system until this manual has
been read and understood. Adherence to the manual recommendations ensures
a problem-free installation and long-term reliability.
System power supplies
During installation of the system or modification to the system, the DC power
supply and batteries should be disconnected to avoid damage to circuit.
Operating environment
Make sure that all system components and peripheral equipment are located
within the limiting environment specified.
Power transients
As with all electronic devices, the system is susceptible to damage by lightning
induced transients. Proper grounding reduces this susceptibility.
Physical mounting
All electronic assemblies should be removed from cabinets prior to any drilling,
filing, reaming, or punching of the enclosure. Before making modifications, verify
that they will not interfere with printed circuit board location.
Wiring
All wiring must fall within the limitations given in the wiring guide, with respect to
loop resistance, loop capacitance, and cross talk from interfering signals.
Screw terminals
Over tightening of screw terminals can damage threads, resulting in reduced
terminal contact pressure and difficulty with screw terminal removal.
Static sensitive components
Printed circuit boards contain static sensitive components. Retain loose printed
circuit boards in static suppressive packing.
System documentation
Comprehensive drawings of the system, signed off by the responsible engineer,
must be kept on record. The system design must take into account local codes
and requirements.
ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual v
Limitations
Equipment compatibility
The extinguishant cylinder release mechanism must be compatible with the ECU
activating circuit. Incompatibility can cause malfunction.
Sensing equipment limitations
The extinguishing control system equipment is reliant on external detection
equipment such as detectors, call points, and fire control panels in order to
activate effective fire alarms. Incorrect positioning of the detectors, limitations in
the detector itself, or incorrect application can result in failure of the detection
process.
Bells and sirens
When the extinguishing control system causes an extinguishing discharge, the
appropriate fire bells and sirens sound. These could prove useless unless they
are situated in close proximity to the people they are supposed to alert.
vi ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual
ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual 1
Chapter 1
System wiring
Summary
This chapter provides information on system wiring.
Content
Wiring standards 2
Wiring connections 3
Surge protection 3
Loop wiring 4
Additional information 10
Connecting the ZP3-ECU 11
Connecting the ZP3-ECU to ZP3-ECUS status units 12
Chapter 1: System wiring
2 ZP3-ECU Extinguishing Control Unit Installation and Commissioning Manual
Wiring standards
All wiring must be installed in compliance with local codes, and in accordance
with the requirements of the local authority having jurisdiction.
Fire alarm systems must remain operative during the initial phase of a fire. It is
therefore important that certain wiring practices are followed, and must comply to
British Standard BS 5839-1: Sections 17 and 24.
WARNING: The wiring connection to the extinguishant cylinder actuator is a low
impedance circuit, which can draw up to 1 A during actuation. Make sure that
wiring to the actuator is of sufficient capacity to avoid wiring resistance voltage
loss.
Otros manuales para ZP3-ECU
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unidad de control de Ziton
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
