Zinwell ZPlus-B191-OD Manual de usuario
Wireless LAN Device Series
WLAN Outdoor Bridge
ZPlus-B191-OD User’s Manual
Version. 1.02 (06.01.2004)
2
Notice
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions：(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Warning：Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions：(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The user’s manual or instruction manual for an intentional or unintentional radiator shall caution
the user that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE：This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures：
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
needed.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter
Shielded interface cables must be used in order to comply with emission limits.
This EUT is incompliance with SAR for general population /uncontrolled exposure limits in
ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and
procedures specified in OET Bulletin 65 Supplement C
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter
CAUTION：
1. The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent
structures with a separation distance of at least 2 meters from all persons and must
not be co-located or operating in conjunction with any other antenna or
transmitter. Users and installers must be provided with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure
compliance.
2. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
3. This equipment is only allowed to be professionally installed.
3
4
Contents
1INTRODUCTION...................................................................................................................................................6
2HARDWARE INSTALLATION............................................................................................................................7
2.1 PACKING LIST...................................................................................................................................................7
2.2 HARDWARE INSTALLATION...............................................................................................................................8
3SOFTWARE CONFIGURATION.......................................................................................................................12
3.1 ENTER WEB CONFIGURATION PAGE .................................................................................................................12
3.2 WLANACCESS POINT STATUS.......................................................................................................................12
3.3 WIRELESS LAN SETTING ...............................................................................................................................14
3.3.1 Basic settings ............................................................................................................................................14
3.3.2 Wireless Advanced Settings.......................................................................................................................17
3.3.3 Wireless Security setup..............................................................................................................................19
3.3.3.1 WEP Encryption Setting.......................................................................................................................19
3.3.3.2 WEP Encryption with 802.1x Setting...................................................................................................22
3.3.3.3 WPA Encryption Setting .......................................................................................................................23
3.3.4 Wireless Access Control............................................................................................................................24
3.3.5 Wireless Site Survey..................................................................................................................................26
3.3.6 WDS Settings ............................................................................................................................................27
3.4 LAN INTERFACE SETUP..................................................................................................................................28
3.4.1 Using the Fixed IP....................................................................................................................................28
3.4.2 Using DHCP Client ..................................................................................................................................29
3.4.3 Enable DHCP Server................................................................................................................................30
3.5 WLANAPSTATISTICS ...................................................................................................................................31
3.6 UPGRADE FIRMWARE .....................................................................................................................................32
3.7 SAVE/RELOAD SETTINGS................................................................................................................................32
3.8 PASSWORD SETUP...........................................................................................................................................33
4TECHNICALSPECIFICATION ........................................................................................................................34
5WIRELESS CONNECTION ARCHITECTURE ..............................................................................................36
5.1 Infrastructure mode ..................................................................................................................................36
5.2 Ad-Hoc mode ............................................................................................................................................36
5.3 WIRELESS APFUNCTIONS ..............................................................................................................................37
5.3.1 Access Point Mode....................................................................................................................................37
5.3.2 Access Point Client Mode (ad-Hoc)..........................................................................................................38
5.3.3 Access Point Client Mode (Infrastructure)...............................................................................................38
5.3.4 Wireless Repeater......................................................................................................................................39
5
5.3.5 WDS (Wireless Distribution System).........................................................................................................39
5.3.6 Wireless Bridge.........................................................................................................................................40
5.4 SELECTING AN APPROPRIATE SITE...................................................................................................................41
5.5 POWER OVER ETHERNET ................................................................................................................................41
6
1 Introduction
ZINWELL ZPlus-B191-OD Wireless Outdoor Bridge is fully complying with 802.11b standard,
featuring with easy-to-install, and easy-to-manage, building-to-building and building to
multibuildings connection.
Our Outdoor Bridge is a flexible and cost-effective product which allows you to connect LANs
located in far distant buildings with data rate up to 11Mbps, ZPlus-B191-OD is an idea device to
replace the expensive lease lines, such as T1 line or fiber optics.
With Power over Ethernet function, ZPlus-B191-OD reduces installation expenses and
increases location options by using a single Ethernet cable to supply both data and power to
our Wireless Outdoor Bridge.
Applications
zPoint-to-Point / Point-to-Multipoint Architecture
zIndoor/Outdoor Architecture
zEasy Installation
Features
zComplied With IEEE 802.11b 2.4GHz Standard
zExcellent Range with Power Build-in Amplifier
zMaximum Sensitivity of 89dBm at 11Mbps
zData Security with 64/128- Bit WEP Encryption
2 Hardware Installation
This Chapter helps you to quickly and easily install the hardware.
2.1Packing List
Before you start install the Wireless Outdoor Bridge, you should check the following
packages you must have：
zWireless Outdoor Bridge * 1
zMounting Kits * 1
zWaterproof RJ-45 Cable (30M) * 1
zWaterproof RF Cable (1M) * 1
zPower Over Ethernet Kits * 1
zGrounding Wired * 1
z2.5” /4” U bolts * 2 and Anchor * 4
z6 / 9 dBi omni directional antenna * 1
Package Picture Package Name Package Picture Package Name
Wireless
Outdoor
Bridge
Mounting
Kits
Waterproof
RJ-45 Cable
Waterproof
RF Cable
7
Power Over
Ethernet Kits
Grounding
Wire
2.5” /4” U
bolts and
Anchor
6 / 9 dBi
omni
directional
antenna
2.2Hardware Installation
After you check all of your packages are ready, you can start installing your wireless
outdoor bridge. You can mount to a pipe or a side of a building. The steps showed in
following：
1. You must mount the ZPlus-B191-OD into the bracket first.
Note: ALL the 4 screws had been tightly onto the Wireless Outdoor Bridge and
bracket
2. You can use the 2” inch or 4” inch U bolts to mount on the pipe.
The two U bolts must tightly mount and take care not to over-tighten
3. After check the ZPlus-B191-OD is mount well, you can connect two cables, Waterproof
RJ-45 network cable and RF cable, and the grounding wire.
The waterproof RF cable must tightly onto the Wireless Outdoor Bridge and another
side that link to the Antenna better to have the lightening protector
4. The waterproof RJ-45 cable also had been tightly onto the Wireless Outdoor Bridge and
another side that be plugged into PoE device.
8
ZPlus-B191-OD Cable connection ZPlus-B191-OD grounding wire connection
Note:
DON’T plug the power cord into PoE device to power on the system before you
finish install the antenna and grounding wire to ensure the safety.
You can follow the figure to mount the ZPlus-B191-OD quickly.
9
You can also mount the ZPlus-B191-OD on the wall to fit in your environment.
In the ZPlus-B191-OD indoor part installation, if the RJ-45 cable’s length is not enough for
you to link to your network device, you can extend the cable length, but you need to careful
the maximum length of the RJ-45 cable is 100M.
When you plug the RJ-45 cable into the PoE device, you should use the normal RJ-45
cable to plug into the “DATA IN” to connect to hub/switch or use the crosslink Rj-45 cable to
connect to user’s PC.
Then the waterproof RJ-45 cable must connect to the “P+DATA OUT” port.
Note:
Please careful not to plug inversely the two cables. This way maybe damages
the devices!
10
Otros manuales para ZPlus-B191-OD
1
Tabla de contenidos
Otros manuales de Hardware de red de Zinwell
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
