Zinwell ZPlus-B191-OD Manual de usuario
Wireless LAN Device Series
WLAN Outdoor Bridge
ZPlus-B191-OD User Manual
Version. 1.03 (07.15.2004)
1
Notice
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions：(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Warning：Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions：(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The user’s manual or instruction manual for an intentional or unintentional radiator shall caution
the user that changes or modifications not expressly ODU proved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE：This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures：
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is needed.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly ODU proved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter
Shielded interface cables must be used in order to comply with emission limits.
This EUT is incompliance with SAR for general population /uncontrolled exposure limits in
ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and
procedures specified in OET Bulletin 65 Supplement C
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter
CAUTION：
1. The antenna(s) used for this transmitter must be fixed-mounted on outdoor
permanent structures with a separation distance of at least 2 meters from all persons
and must not be co-located or operating in conjunction with any other antenna or
transmitter. Users and installers must be provided with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure
compliance.
2. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
3. This equipment is only allowed to be professionally installed.
2
3
Contents
1INTRODUCTION..................................................................................................................................................4
2HARDWARE INSTALLATION ............................................................................................................................5
2.1 PACKING LIST ................................................................................................................................................5
2.2 HARDWARE INSTALLATION ............................................................................................................................6
3SOFTWARE CONFIGURATION........................................................................................................................10
3.1 ENTER WEB CONFIGURATION PAGE...............................................................................................................10
3.2 STATUS OF WLAN OUTDOOR BRIDGE.........................................................................................................10
3.3 WIRELESS LAN SETTING.............................................................................................................................12
3.3.1 Basic settings..........................................................................................................................................12
3.3.2 Wireless Advanced Settings ....................................................................................................................15
3.3.3 Wireless Security setup...........................................................................................................................17
3.3.3.1 WEP Encryption Setting ....................................................................................................................17
3.3.3.2 WEP Encryption with 802.1x Setting.................................................................................................19
3.3.3.3 WPA Encryption Setting.....................................................................................................................20
3.3.4 Wireless Access Control .........................................................................................................................21
3.3.5 Wireless Site Survey................................................................................................................................23
3.3.6 WDS Settings..........................................................................................................................................24
3.4 LAN INTERFACE SETUP...............................................................................................................................26
3.4.1 Using the Fixed IP..................................................................................................................................26
3.4.2 Using DHCP Client................................................................................................................................28
3.4.3 Enable DHCP Server .............................................................................................................................29
3.5 WLAN AP STATISTICS ................................................................................................................................30
3.6 UPGRADE FIRMWARE...................................................................................................................................31
3.7 SAVE/RELOAD SETTINGS .............................................................................................................................31
3.8 SETUP PASSWORD ........................................................................................................................................32
4WIRELESS CONNECTION ARCHITECTURE.................................................................................................34
4.1 INFRASTRUCTURE MODE..............................................................................................................................34
4.2 AD-HOC MODE.............................................................................................................................................34
4.3 WIRELESS AP FUNCTIONS ...........................................................................................................................35
4.3.1 Access Point Mode .................................................................................................................................35
4.3.2 Access Point Client Mode (Ad-Hoc).......................................................................................................36
4.3.3 Access Point Client Mode (Infrastructure).............................................................................................36
4.3.4 Wireless Repeater...................................................................................................................................37
4.3.5 WDS (Wireless Distribution System) ......................................................................................................37
4.3.6 Wireless Bridge.......................................................................................................................................38
4.4 SELECTING AN APPROPRIATE SITE ................................................................................................................39
4.5 POWER OVER ETHERNET..............................................................................................................................39
4
1 Introduction
ZINWELL ZPlus-B191-OD Wireless Outdoor Bridge Unit (herein after referred as ODU) is
fully complying with 802.11b standard, featuring with easy-to-install, easy-to-manage, and
point-to-point and point-to-multipoint connection.
Our ODU is a flexible and cost-effective product which allows you to connect LANs located
in fart buildings with data transmitting rate up to 11Mbps. Our ODU is an ideal device that let
you can replace the expensive lease lines, such as T1 line or fiber optics.
With Power over Ethernet function, our ODU reduces installation expenses and increases
location options by using a single Ethernet cable to supply both data and power to our ODU.
ODU applications
Point-to-Point / Point-to-Multipoint Architecture
Indoor/Outdoor Architecture
Easy Installation
Features
Complied With IEEE 802.11b 2.4GHz Standard
Excellent Range with Build-in Power Amplifier and superior sensitivity receiver
Data Security with WEP, WPA-PSK, TKIP
2 Hardware Installation
This Chapter helps you to install the hardware in a quick and easy way.
2.1 Packing List
Before you start to install the ODU, make sure the package should contain the following
items：
Wireless Outdoor Bridge unit * 1
Mounting Kit * 1
Waterproof (IP67) RJ-45 Cable (30M) * 1
Waterproof (IP66) RF Cable (1M) * 1
Power Over Ethernet Kit * 1
Ground Wire * 1
2.5” /4” U bolts * 2 and Anchor * 4
6 dBi omni directional antenna * 1 (separated package)
RJ-45 Cable (1.5M) * 1
ODU Mounting Kit
Waterproof RJ-45 Cable Waterproof RF Cable
5
Power Over Ethernet Kit Ground Wire
RJ-45 Cable 6 dBi omni directional
antenna
2.5” /4” U bolt and Anchor
2.2 Hardware Installation
Once you check off everything from the package, you can start to install the ODU. You can
mount to a pipe, a pole or to the side of a building. The steps are showed in the
following：
1. You must mount the ODU into the bracket first.
Note: ALL the 4 screws had been tightened onto the ODU and bracket
6
2. You can use the 2” inch or 4” inch U bolt to mount on the pipe, depending on the radius
of the pipe. (Wall mounting is referred to Wall Mounting Figure) The two U bolts must
be mounted tightly. Be aware of not over-tighten the U bolt.
Pipe Mounting Figure
7
Wall Mounting Figure
3. After checking the ODU is mounted well, you can connect the following two cables: the
Waterproof RJ-45 network cable to “P+ DATA OUT” port of ODU and the RF cable to
antenna port. Additional waterproof tool, such as waterproof tape, is recommended
to use to enhance the waterproof function. It is suggested to have a lightening
protector between antenna and antenna port. Connecting the ground wire as the
figure of “ODU ground wire connection.”
ZPlus-B191-OD Cable connection ZPlus-B191-OD ground wire connection
4. Plug the other end of the waterproof RJ-45 cable to the PoE device. The PoE device
is guaranteed only in indoor environment.
Note: DON’T plug the power cord into PoE device to power on the system before
you finish install the antenna and Ground wire to ensure the safety.
DATA
IN
P+DATA
OUT
In the ODU indoor part installation, if the RJ-45 cable’s length is not long enough for you to
8
link to your network device, you can extend the cable length. However, make sure the
maximum length of the RJ-45 cable is 100M (about 109 yards) for normal operation under
802.3 standard.
When you plug the regular RJ-45 cable into the PoE device, you should use the regular
RJ-45 cable to plug into the “DATA IN” of “Power Over Ethernet Kit” to connect to
hub/switch or use the crosslink Rj-45 cable (Not included in the Packing List) to connect
with user’s PC.
The waterproof RJ-45 cable must be connected to the “P+DATA OUT” port.
Note: Be careful! Don’t plug the two cables inversely. It will damage the
devices!
Refer to the following figure for the complete system connection.
9
Power injector
ZPlus-B191-OD
Waterproof RF cable
RJ-45 cable
Waterproof RJ-45 cable
Power cord
Indoor
Outdoor
Power supply
HUB / SWITCH
Antenna
Ground wire
Otros manuales para ZPlus-B191-OD
1
Tabla de contenidos
Otros manuales de Hardware de red de Zinwell
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
