ZiLOG Wireless Zdots Manual de usuario
Copyright ©2010 by Zilog®, Inc. All rights reserved.
www.zilog.com
Introduction
This Quick Start Guide provides instructions to use Zilog’s Wireless Zdots®Single Board
Computer (SBC) with the Demo project WLANDemo.zdsproj. WLANDemo.zdsproj is a
sample project in which the communication of a PC to a web page is wireless, it is run by
Zdots SBC. The WLANDemo.zdsproj is used along with standard Zilog TCP/IP (ZTP)
software suite. This Demo project can only be used on Wireless Zdots SBC. Do not use
this Demo project on Zilog’s eZ80Acclaim!®development kit. This project can also be
used as the starting point for your application development.
Figure 1. Wireless Zdots®SBC Development Kit
Wireless Zdots® Single Board
Computer Development Kit
Quick Start Guide QS007504-0410
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 2 of 19
Figure 2. Wireless Zdots®SBC and Base Board
Figure 3. Wireless Zdots®SBC
Wireless Module
RS-232
Adapter
Wireless Development kit Base Board
Prototype Area
ZDI Interface
eZ80F91
NOR Flash
SRAM
RS-232/PWR
MII Input/Output
On-Board Antenna
Input/Output
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 3 of 19
Figure 4. Wireless Base Board
Kit Contents
This section describes the hardware and software requirements for installing and using
Wireless Zdots®Single Board Computer Development Kit.
Hardware
The hardware included in this kit are:
•eZ80AcclaimPlus! Wireless Zdots SBC
•eZ80AcclaimPlus! Wireless Zdots SBC Development Kit Base Board
•RS-232 Adapter
•USB Smart Cable
•5 V DC Power Supply
•RS-232 Cable
Wireless module Plug-in Headers
ZDI
DC Power Input
Prototype
Test Points
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 4 of 19
The additional hardware that are required to run the Demo (not included
in the kit) are:
1. A USB to Serial Adapter for host PC that do not have a serial COM
port.
2. Wireless LAN router.
Software and Documentation (on CD-ROM)
The software included in this kit are:
•Zilog Developer Studio II (ZDS II)-eZ80 Acclaim!®
•Zilog TCP/IP Stack (ZTP) ZDS - Object Code
1. For latest revision, visit www.zilog.com.
2. For procedure to download the ZTP software, see Downloading the
ZTP Software on page 18.
System Requirements
Table 1 lists the system requirements for running
ZDS II
.
Table 1. ZDS II System Requirements
Recommended Configuration Minimum Configuration
PC running Microsoft Windows XP
Professional
PC running Microsoft Windows XP Professional/
Windows 2000 SP4/Windows 98 SE
Pentium III/500 MHz or higher
processor
Pentium II/233 MHz processor
128 MB RAM 96 MB RAM
110 MB hard disk space 25 MB hard disk space (documentation not installed)
Super VGA video adapter Super VGA video adapter
CD-ROM drive CD-ROM drive
One or more RS-232
communications ports
One or more RS-232 communications ports
USB high-speed port USB high-speed port
Notes:
Notes:
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 5 of 19
Installing the ZDSII Software and Kit Documentation
Follow the steps below to install the ZDS II and documentation:
1. Insert the ZDS II CD into the CD-ROM drive. DemoShield launches automatically. If
the DemoShield does not launch automatically, open the Windows Explorer, browse
to your CD-ROM drive, and double-click launch.exe to launch the installer.
2. From the product installer list you can choose to install ZDS II alone, or both ZDS II
and associated documentation. You can also copy the documentation directly from
your CD-ROM drive to your hard disk using Windows Explorer or read the documen-
tation directly from the CD-ROM itself.
For customer service and technical support, Zilog®recommends you to create an account
on http://support.zilog.com.
Installing the USB Smart Cable
Follow the steps below for installing the USB Smart Cable and associated driver software.
Windows Vista-32
Follow the steps below to install the USB Smart Cable for Windows Vista-32.
1. Connect the USB Smart Cable to the Host PC. The Found New Hardware dialog box
is displayed.
2. Select Locate and install the driver software (recommended). The Driver Soft-
ware Installation window is displayed, and then the Found New Hardware-USB
Smart Cable dialog box is displayed.
3. Select I don’t have the disc. Show me other options.
4. Select Browse my computer for driver software (advanced).
5. Browse to the following driver directory:
<ZDS II Installation Directory>\device drivers\USB
The Windows Security dialog box is displayed.
6. Select Install this driver software anyway.
7. When the software is installed, click Closed.
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 6 of 19
Windows XP
Follow the steps below to install the USB Smart Cable for Windows XP:
1. Connect the Zilog USB device to the Host PC. The Found New Hardware Wizard
should activate automatically after connecting the Zilog USB device for the first time;
select No, not at this time if asked to connect to Windows Update.
2. Select Install from a list or specific location (Advanced); then click Next.
If the Windows Logo testing dialog appears, select Continue Anyway.
3. Select Search for the best driver in these locations and Include this location in
search:.
4. Browse to the following driver directory and click Next.
<ZDS installation>\device drivers\USB\
5. Click Next after the appropriate driver is found.
6. Click Finish to complete the installation.
Windows 2000
Follow the steps below to install the USB Smart Cable for Windows 2000:
1. Connect the Zilog USB device to the Host PC. The Found New Hardware Wizard
should activate automatically after connecting the Zilog USB device for the first time.
2. Click Next in the Found New Hardware Wizard after it has been activated.
3. Select Search for a suitable driver for my device (Recommended) and click Next.
4. Select Specify a location and click Next.
5. Browse to the following driver directory and click OK.
<ZDS installation>\device drivers\USB\
6. Click Next after the appropriate driver is found.
7. Click Finish to complete the installation.
Note:
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 7 of 19
Windows 98SE
Follow the steps below to install the USB Smart Cable for Windows 98SE:
1. Connect the Zilog USB device to the Host PC. The Add New Hardware Wizard
should activate automatically after connecting the Zilog USB device for the first time.
2. Click Next in the Add New Hardware Wizard after it has been activated.
3. Select Search for the best driver for your device (Recommended) and click Next.
4. Select Specify a location: and browse to the following driver directory, and click
Next.
<ZDS installation>\device drivers\USB\
5. Click Next after the appropriate driver is found.
6. Click Finish to complete the installation.
Hardware Setup
Figure 5 displays the hardware setup for the ZTP Wireless Local Area Network (WLAN)
Demo application that is used to demonstrate wireless data transfer.
Figure 5. Hardware Setup for the ZTP WLAN Demo Application
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 8 of 19
Figure 6. RS-232 Adapter
Follow the steps below to set up the hardware:
1. Connect Zdots SBC to J1 of the Wireless base board. See Figure 2 on page 2 for actual
image. The SBC must be connected before applying the power.
Pin 1 of Zdots SBC should match the pin 1 of the base board; this is
indicated by square solder around the pin.
2. Connect the RS-232 adapter (99C1067-001G) to the WLAN Zdots SBC J3 header.
Pin 1 is indicated by the square solder on the solder side.
3. Connect the USB Smart cable (or any Zilog Debug tool) to the 6-pins ZDI interface on
the Wireless Base Board on your development PC. See Connecting the USB Smart
Cable to the Development Board on page 9.
4. Connect the RS-232 cable to the RS-232 adapter P1 connector and the other end to the
communication port (COM1) of the PC.
This is connected on your PC as displayed in Figure 5 on page 7.
5. Connect the power supply (5 V DC) cable to the Wireless Base board J4 connector.
6. Set up an access point (AP) in the test area and power it ON. For information on how
to set up the wireless router, see Configuring the Router on page 15.
RS-232 Driver
6 Pin TTL Level
TX, RX, RTS, CTS,
3.3 V and Ground RS-232 DB9
Note:
Note:
Note:
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 9 of 19
Connecting the USB Smart Cable to the Development Board
The power to the development board must be disconnected or turned
OFF before connecting or disconnecting the USB Smart Cable.
Attach one end of the six-conductor ribbon cable (included) to the USB Smart Cable six-
pin DBG connector (see Figure 7). Attach the free end of the ribbon cable to the DBG con-
nector (ZDI Interface) on the development board. Ensure that pin 1 on the ribbon cable
(indicated by the dark stripe) is aligned with pin 1 on the target connector (indicated by a
square solder on the DBG pin).
Figure 7. Connecting the Six-Conductor Ribbon Cable to the USB Smart Cable
Configuring the HyperTerminal Application
The HyperTerminal program must be configured before starting the Demo application.
Follow the steps below to configure the HyperTerminal application:
1. In Windows operating system, launch the HyperTerminal application by navigating to
Start All Programs Accessories Communications HyperTerminal.
The Connection Description dialog box is displayed.
2. Enter the name for a new connection in the Connection Description dialog, and click
OK. The Connect To dialog box is displayed.
3. In the Connect Using text field, select the port (COM1 or COM2) to which the serial
cable is connected. Click OK to open the Port Settings dialog box for the selected
port.
Caution:
Wireless Zdots® Single Board Computer Development Kit
QS007504-0410 Page 10 of 19
4. In the Port Settings tab of dialog box, enter the following values in the respective text
fields:
5. Click OK to establish connection to the eZ80®development platform using the serial
port.
How to Execute WLAN Demo Application
Running the RAM-Based WLAN Demo Project using the ZDS II
Toolset
Follow the steps below to execute the WLAN Demo project in the Zilog Developer Studio
II (ZDS II) development environment:
The following procedures reference the WLANDemo.zdsproj located in the
CD-ROM. Insert Zilog TCP/IP Stack (ZTP) ZDS - Object Code Version
X.Y.Z1CD into the CD-ROM drive. InstallShield Wizard appears and starts
installation. Follow the on-screen procedures. By default, it is installed at
C:\Program Files\ZiLOG\ZTP_X.Y.Z_Lib_ZDS.
1. Set up the hardware as displayed in Figure 5 on page 7.
2. To launch ZDS II, navigate to Start All Programs Zilog ZDS
IIeZ80Acclaim!_<Version> _ZDS II-eZ80Acclaim!_<Version>.
3. Select Open Project from the File menu in ZDS II to open the sample ZTP Demo
project located in the following path:
For ZDSII - eZ80Acclaim! 5.1.0:
C:\Program Files\ZiLOG\ZDSII_eZ80Acclaim!_5.1.0\ZTP\ZTP2.3.1_Lib\ZTP\
SamplePrograms\WLANDemo\WLANDemo.zdsproj
Bits per second 57600 bps
Data bits 8
Parity None
Stop Bits 1
Flow control None
1 Where X.Y.Z refers to the major, minor, and revision number of the release.
Note:
Tabla de contenidos
Manuales populares de Computadora de placa única de otras marcas
WIN Enterprises
WIN Enterprises PL-80910 Manual de usuario
AXIOMTEK
AXIOMTEK SBC81206 Series Manual de usuario
Embest
Embest SOM-PH8800 Manual de usuario
SeaLevel
SeaLevel SBC-R9 Manual de usuario
SMART Embedded Computing
SMART Embedded Computing ATCA-8310 Manual de usuario
WinSystems
WinSystems PPM-LX800-G Manual de usuario
GIGAIPC
GIGAIPC QBiX-PPC Series Manual de usuario
OLIMEX
OLIMEX A10S-OLinuXino-MICRO Manual de usuario
Commell
Commell FS-978 Manual de usuario
GIGAIPC
GIGAIPC QBiP-8665A/ Manual de usuario
VersaLogic
VersaLogic Python EBX-11 Manual de usuario
Micro Computer Specialists
Micro Computer Specialists IRV-3702 Manual de usuario
