ZiLOG EZ80 Manual de usuario

ZiLOG Worldwide Headquarters • 532 Race Street • San Jose, CA 95126-3432

Telephone: 408.558.8500 • Fax: 408.558.8300 • www.ZiLOG.com

UM015201-0603

ZiLOG Development Platforms

eZ80

Sales Demonstration Platform

User Manual

User Manual UM015201-0603

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to

request copies of publications, contact:

ZiLOG Worldwide Headquarters

532 Race Street

San Jose, CA 95126-3432

Telephone: 408.558.8500

Fax: 408.558.8300

Document Disclaimer

ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service

names mentioned herein may be trademarks of the companies with which they are associated.

technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME

LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR

TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR

INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR

TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Except with the express written approval of ZiLOG, use of

information, devices, or technology as critical components of life support systems is not authorized. No licenses are

conveyed, implicitly or otherwise, by this document under any intellectual property rights.

User Manual UM015201-0603

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

iii

Safeguards

The following precautions must be observed when working with the devices

described in this document.

Always use a grounding strap to prevent damage resulting from electrostatic dis-

charge (ESD).

Caution:

User Manual UM015201-0603 Table of Contents

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

Table of Contents

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

eZ80® Sales Demonstration Platform Block Diagram . . . . . . . . . . . . . . . . . . . . . 2

Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Jumper Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

eZ80® Sales Demonstration Platform Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PCB Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Demonstration Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Using ZDSII to Download and Run ez80l92_demo_platform.pro . . . . . . . . . 7

Peripheral Bus Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

I/O Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Product User Guide UM015201-0603

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

List of Figures

Figure 1. The eZ80® Sales Demonstration Platform, Top View . . . . . . . . . . . . 1

Figure 2. eZ80® Sales Demonstration Platform Block Diagram . . . . . . . . . . . . 2

Figure 3. eZ80® Sales Demonstration Platform Block Diagram . . . . . . . . . . . . 3

Figure 4. eZ80® Sales Demonstration Platform Demo Setup . . . . . . . . . . . . . . 4

Figure 5. eZ80® Sales Demonstration Platform Peripheral Bus Connector Pin

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 6. eZ80® Sales Demonstration Platform I/O Connector Pin Configuration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 7. eZ80® Sales Demonstration Platform Schematic . . . . . . . . . . . . . . 14

Figure 8. eZ80® Sales Demonstration Platform . . . . . . . . . . . . . . . . . . . . . . . 15

User Manual UM015201-0603

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

List of Tables

Table 1. eZ80® Sales Demonstration Platform Demo Features . . . . . . . . . . . 7

Table 2. Peripheral Bus Connector Pin Identification (see Figure 5 for Pin #s) 9

Table 3. I/O Connector Pin Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

User Manual UM015201-0603 Kit Contents

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

Kit Contents

•

One (1) eZ80® Sales Demonstration Platform with LCD Display and module

•

Four (4) AA batteries

•

One (1) ZPAK II Debug Interface Module (includes TIM)

•

One (1) 40-connector ribbon cable

•

One (1) DB9-DB9 Serial I/O Cable

•

One (1) ID10 to DB9 cable

•

One (1) Ethernet Hub

•

One (1) Ethernet Hub User Manual

•

Two (2) 7.5V AC Power supplies for Ethernet hub (one international)

•

Two (2) 5V AC Power supplies with adapters

•

One (1) CDROM with ZDS II software, sample projects, and documentation

•

Three (3) Cat-5 Patch Cables

The eZ80® Sales Demonstration Platform works with the eZ80L92,

eZ80F91, and eZ80F92 modules. For simplicity, this document refers to

the eZ80L92 module. Instructions apply to all three modules, however.

Introduction

The eZ80® Sales Demonstration Platform provides a flexible, portable platform for

conducting training programs and demonstrations using a number of ZiLOG

microcontroller and microprocessor devices. A ZiLOG eZ80®processor-equipped

module plugs into this platform.

Figure 1 shows the top view of the eZ80® Sales Demonstration Platform.

Figure 1. The eZ80® Sales Demonstration Platform, Top View

Note:

User Manual UM015201-0603 eZ80® Sales Demonstration Platform Block

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

The eZ80® Sales Demonstration Platform can be powered by the on-board batter-

ies (stand-alone configuration) or by the AC adapter. Both configurations feature:

•

Serial communication using eZ80®UART ports and adapter board connectors

•

Ethernet communication using the eZ80L92 or eZ80F92 module

•

LCD displays relevant demo data

•

ZDI operation using external ZPAK

Do not use battery power and AC power at the same time. Doing so will damage

the board.

eZ80® Sales Demonstration Platform Block Diagram

Figure 2 illustrates a block diagram of the eZ80® Sales Demonstration Platform.

Figure 2. eZ80® Sales Demonstration Platform Block Diagram

Hardware Overview

The following section provides an overview of the eZ80® Sales Demonstration

Platform. The current release supports the eZ80L92 module, p/n

eZ80L925048MOD.

Requirements

The eZ80® Sales Demonstration Platform requires an eZ80®module and 5VDC

@ 1.5A, provided by an AC adapter or four 1.5V batteries.

Caution:

Reset ZDI

RS-232

Driver

5 volts

Power Supply

Four 1.5V

3 Volts

eZ80® Module

RS-232

Batteries

LCD

User Manual UM015201-0603 Jumper Settings

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

Jumper Locations

Figure 3 illustrates the jumpers on the eZ80® Sales Demonstration Platform.

Figure 3. eZ80® Sales Demonstration Platform Block Diagram

Jumper Settings

J1 CPU Acknowledgement for

Motorola Bus Mode

IN = enabled

OUT = disabled (default)

J3 External Flash Access on

eZ80®Module

IN = Flash access disabled

OUT = Flash access enabled (default)

J4 External Flash Boot Block Write

Access on eZ80®Module

IN = write enabled

OUT = write disabled (default)

J6 IrDA Control IN = IrDA transceiver on the eZ80®module disabled (default)

OUT = IrDA transceiver on the eZ80®module enabled when

PB6 is set to 0

J12 COM2 (J11) Control IN = Disabled

OUT = Enabled (default)

J14 COM1 (J13) Control IN = Disabled

OUT = Enabled if PB6 set to 1 (default)

ZDI

JP2

JP1 COM2COM1

LCD Display

SW1

J14

5VDC

Battery Switch

OFF

I2C Display

Connector

J12

J1 J6

SW2 SW3

User Manual UM015201-0603 eZ80® Sales Demonstration Platform Setup

ZiLOG Development Platforms

eZ80® Sales Demonstration Platform

eZ80® Sales Demonstration Platform Setup

Overview

A single software project called ez80l92_demo_platform.pro is included on the

eZ80® Sales Demonstration Platform CD-ROM. The demo software is preloaded

into eZ80L92 Flash memory. Connect the demonstration platform to a PC as

described below and the demo is ready to run.

Instructions for loading the demo project are also included for code download and

debugging demonstrations.

PCB Notes

•

To use batteries in this demonstration, load four 1.5-Volt batteries into the bat-

tery holder and turn on battery switch S1.

•

X10 port J10 is not loaded for this release.

•

The LCD module is a Matrix Orbital LCD2041. For further information about

the Matrix Orbital LCD2041 20-column by 4-line display, go to www.matrixor-

bital.com. This LCD display is a 5-volt display with an I2C or RS-232 interface.

This kit uses the I2C interface only.

Demonstration Setup Procedure

Ensure that the eZ80® Sales Demonstration Platform is configured and working

properly as described in the eZ80® Sales Demonstration Platform Quick Start

Guide (QS0024). Then disconnect the ZPAKII from the PC and platform and per-

form the following procedures. Use Figure 4 as a reference.

Figure 4. eZ80® Sales Demonstration Platform Demo Setup

ZDI

JP2

JP1 COM2COM1

LCD Display

SW1

J14

5VDC

Battery Switch

OFF

I2C Display

Connector

J12

J1 J6

SW2 SW3

To open COM port

on PC

Otros manuales para eZ80

Tabla de contenidos

Otros manuales de Hardware de computadora de ZiLOG

ZiLOG

ZiLOG eZ80F91 Manual de usuario

ZiLOG

ZiLOG Z8 GP ZGP323 Manual de usuario

ZiLOG

ZiLOG Z86C5000ZEM Manual de usuario

ZiLOG

ZiLOG eZ8 Manual de usuario

ZiLOG

ZiLOG Z80 series Manual de usuario

ZiLOG

ZiLOG Z80-AIO Instrucciones de uso

ZiLOG

ZiLOG System 8000 Guía rápida de usuario

ZiLOG

ZiLOG eZ80 Manual de usuario

ZiLOG

ZiLOG Z8018 Series Manual de usuario

ZiLOG

ZiLOG eZ8 Manual de usuario

ZiLOG

ZiLOG Z8 Encore! Z8F04A08100KIT Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario