Zephyr AK0710 Guía de instalación

Este manual sirve para los siguientes modelos

3

Tabla de contenidos

Otros manuales de Campana de ventilación de Zephyr

Zephyr

Zephyr Luce ZLU-E30AS Guía de instalación

Zephyr

Zephyr Verona ZVO-M90AG Guía de instalación

Zephyr

Zephyr Milano Wall ZMI-M90BS Guía de instalación

Zephyr

Zephyr Savona ZSA-E30FB Guía de instalación

Zephyr

Zephyr Luce ZLU-E30BS Guía de instalación

Zephyr

Zephyr ZRO-E30BS Manual de usuario

Zephyr

Zephyr Siena Pro ZSP-E48BS Guía de instalación

Zephyr

Zephyr ZML-M90BG Guía de instalación

Zephyr

Zephyr Okeanito COK-E42SX Guía de instalación

Zephyr

Zephyr Twister AK8000AS Guía de instalación

Zephyr

Zephyr Pisa ZPI-E24BG Guía de instalación

Zephyr

Zephyr Titan AK7636AS Guía de instalación

Zephyr

Zephyr Verona Island ZVN-M90AG Guía de instalación

Zephyr

Zephyr ZPA-M90S Guía de instalación

Zephyr

Zephyr MESA DME-M90ASSX Manual de usuario

Zephyr

Zephyr Titan AK7636AS Guía de instalación

Zephyr

Zephyr Cypress AK7836ASX Manual técnico

Zephyr

Zephyr Z1C-00SU Manual de usuario

Zephyr

Zephyr ALL-M90BBX Manual de operación y mantenimiento

Zephyr

Zephyr ALL-M90BBX Manual de operación y mantenimiento

Zephyr

Zephyr Genova Series Manual de usuario

Zephyr

Zephyr Typhoon AK2100CS Guía de instalación

Zephyr

Zephyr AK7500BS Guía de instalación

Zephyr

Zephyr VALINA ZVA-M60AS290 Manual de usuario

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario

Nibe

Nibe S Series Guía del usuario

www.zephyronline.com

Use, Care and Installation Guide

Tempest I , II

Stainless Steel

Backsplash

AK0710 - 30”

AK0716 - 36”

AK0712 - 42”

AK0718 - 48”

FEB07.0201

Table of Contents

LIST OF MATERIALS —————————–- 2

SPECIFICATION ———————————— 3

INSTALLATION ————————————- 4,5

CLEANING AND

CONTACT INFORMATION ———————— 6

1

List of Materials

1 - Upper Section

1 - Lower Section

2 - Wire Racks

1 - Hardware Packet

2 - Retaining Clips

4 - Hinge Clips

6 - 7/16” Carriage Head Bolts

8 - 5/8” Philips Head Wood Screw

6 - Carriage Head Bolt Nuts

Note: If any parts are missing, please call

1-888-880-8368 for replacements.

2

Specifications

3

Installation

1. Mark a level line on the wall at 16” below bottom of hood.

2. Position the lower section of backsplash (flat part with flange on top) on the wall.

Center it side to side and mark the top and bottom holes. Remove the lower section from

the wall.

3. If installing onto drywall only and not onto studs, insert wall anchors (we recommend EZ

anchors) into the marked holes. If installing onto studs, attach screws without EZ anchors.

4. Attach lower section of backsplash to wall with screws provided.

5. Position upper section of backsplash by engaging its flange with the lower section. Push up

to fully engage flanges*, center it side to side and mark the location of the mounting holes.

Remove the upper section from drywall and install wall anchors into marked holes.

5b.If hood is already installed, attach wall anchors into the (3) holes from inside the hood at the

bottom. These are the holes which the upper section will line up with and mount to the wall.

6. Insert retaining clips and hinge clips to the upper section. The retaining clips go in the top

top two openings and the hinge clips go in the bottom four openings. (see diagram, page 4)

Fasten and tighten nuts to the clips on back of the upper section with the provided

hardware.

7. Attach upper section to wall with screws provided. If hood is already installed, Insert the top

2” lip of the upper section behind the bottom of the hood and line up the holes with the (3)

holes at the bottom of the hood. Insert screws into holes and fasten upper section to wall.

*note: in some installations, the flanges will not fully engage in the final install. This is fine

since the weight of the upper section will rest against the bottom section.

4

Installation

1. For the warming plate option; snap the wire shelves into hinge clips

on the backsplash as shown in the left side shelf diagram.

2. For the spice rack option; attach shelf to hinge clips, as

show in the right side shelf diagram, then rotate shelf upwards and

secure with retaining clip.

5

Cleaning and Contact Information

Cleaning of the backsplash should be done frequently to preserve the

life of the stainless steel. Cleaning should typically be done once or

twice a month depending on your cooking habits.

When cleaning, use a non abrasive cleaner, do not use “orange”

cleaner. Abrasive cleaners may scratch the surface and discolor the

stainless steel. To clean the wire racks, soak them in soapy water.

DO NOT place in a dishwasher as this may discolor the wire racks.

You may also polish the stainless steel by using stainless steel polish.

Make sure when polishing to go along with the grain of the backsplash.

Zephyr Corporation

395 Mendell Street

San Francisco, CA 94124

1-888-880-8368

6