Zenpro SmartControl ZSC1 Manual de usuario
Manual
Version 1.1
Content
1. Device description 3
1.1. Technical data 3
1.2. Kit contents 3
1.3. Back panel 4
1.4. Led diodes 4
1.5. Nameplate 4
1.6. Modes of connection 5
2. First usage 6
2.1. Initialization 6
2.2. Downloading application 6
2.2. Connection through Wi-Fi 7
2.3. Connection through Ethernet cable 8
3. Mobile app –description 9
4. System configuration 10
4.1. Adding devices 10
4.2. Types of devices 11
4.3. Adding groups 14
4.4. Time events 15
4.5. Connection to home Wi-Fi network 16
4.6. Remote access 18
5. PC Web browser control 20
6. Device installation 21
7. Safety precautions 22
2
1. Device description
SmartControl
Central Unit
Power supply 12VDC
Antenna 433MHz Ethernet
Cable Device manual
1.2 Package contents
1.1 Technical data
DC Input
12 V DC
Power Consumption
1,6
W
Interfaces
Wi
-Fi, Ethernet, ISM 433,92MHz
Battery
to sustain clock
Battery CR1220
Casing protection level
IP20
Device description
Zenpro SmartControl Central Unit is a modern controller for roller shutters and other
devices working in 433,92MHz frequency through mobile devices and PC. Zenpro
expands the possibilities of the system by grouping of the devices, time events and
allows for remote access through Internet.
3
1. DC port
2. Reset button 3. Ethernet
4. Antenna
1. DC Port –place where the power supply is
connected. Supply voltage of 9-12 VDC is
allowed.
2. Reset –one short press of the reset
button resets the Wi-Fi settings to default,
holding the button for 5 seconds brings
back the device to factory settings.
3. Ethernet connector –allows to connect
the device to LAN network or home
router through Ethernet cable.
4. Antenna connector –here connect the
antenna provided in the package. The
antenna is responsible for communication
in the 433MHz band.
1.3 Back Panel
1.4 Led diodes on front panel
1. Power
2. Status
3. Ethernet
4. Wi-Fi
1. Power –the diode is on when proper power
supply is connected to the device.
2. Status –the diode is on while the
communication in 433MHz band takes place
and provides additional status information.
3. Ethernet –diode is on when the device is
connected to the LAN through Ethernet cable
4. Wi-Fi –diode is on when the Wi-Fi interface is
on or the device is connected to the local Wi-Fi
network.
1.5 Nameplate –serial number and MAC addresses
On the bottom of the device you can find a nameplate with
following information.
- Device serial number example: S/N: ZN-010002
- MAC address of the Ethernet interface
- MAC address of the Wi-Fi interface 4
1.6 Modes of Work
A – The device provides it’s own Wi-Fi network
C –The devices connects to home router
through home Wi-Fi network
- Central Unit is connected to home Wi-Fi
network
- Allows for optimal placement of the device
in home for maximum range of the 433MHz
interface.
- Detailed description in chapter 4.5
HomeWi-Fi
Home router
B- The device is connected to home router through Ethernet cable
- Central Unit provides own Wi-Fi network with SSID
„SmartControl_SerialNumber”
ex. SmartControl-ZN-010325
- Default mode of work
- Allows to control of the devices without usage of the
external router
- The device can act as a home Wi-Fi router
- No remote access, because lack of the Internet
connection
-The „SmartControl” Wi-Fi network is not encrypted by
default. WPA-PSK2 encryption can be turned on in the
mobile application in the settings tab.
- The device is connected to the router
through Ethernet cable
- Simplest way of configuration
- We can log into home Wi-Fi network to
connect to the Zenpro device
-The „SmartControl” Wi-Fi network may
be turned off in the settings
- Remote access available
Home Wi-Fi
5
2. First usage
1. After connecting the device to power
supply, the Power diodes should be on. The
status diodes wile be blinking until device
will finish booting.
2. After approximately 60 seconds, the status
diode will stop blinking. The device is ready
to work.
6
2.1 Device initialization
2.2 Downloading Zenpro SmartControl mobile App
You can download the Zenpro SmartControl from the Google Play
or the AppStore.
Type in the store browser: „Zenpro SmartControl”
Or use the QR-code below:
ANDROID iOS
The app will display configuration screen. Press the search button to find the
Central device IP Address. After successful connection tap the „Connect”
button.
2.3 Connection through Wi-Fi network provided by the
Zenpro SmartControl device
After finished initialization (when the status blink stops blinking). The device provides own
Wi-Fi network with SSID „SmartControl_SerialNumber”. Using the mobile device
(Smartphone or Tablet) we open the device settings , pick up the Wi-Fi settings and
display the list of available Wi-Fi networks. An unencrypted Wi-Fi network
„SmartControl_SerialNumber” should appear. Connect to the SmartControl network and
then open the downloaded Zenpro SmartControl mobile App.
7
2.3 . Connection to home router with Ethernet cable
8
Home Wi-Fi network
home router
Ethernet
Cable
1. Connect the Ethernet cable provided with the device to the
port on the back of the device and to the home router.
2. Next connect your mobile device to home Wi-Fi network (don’t use the
„SmartControl”Wi-Fi network). Turn on the Zenpro SmartControl mobile App a use
the „Search” button. After successful search, type the „Connect” button –the
device is ready to use.
3. Mobile App –view description
1. Mobile application has three main views.
•Devices –allows to control the devices and groups of
the devices added to the system.
•Events –configuration, adding and running time events
•Settings –allows to change the device settings like Wi-Fi
and remote access settings, and add devices and groups
of devices into system.
2. Switching between screens can be done be swiping the
screen from side to side or pressing the tabs.
Devices Events Settings
9
Status bar
Gives information about the Central Unit status.
•LAN –device is connected to LAN
•NET–connection through Internet
•OK –the command was successfully done
•Work –The mobile device is waiting for a
confirmation from the Central Unit.
4. System configuration
Go to „Settings” tab, then
„Devices”.
4.1. Adding devices to the system
Pick the „Add device”
option
You can verify whether the device was added
properly with use of the buttons:
10
Choose the type of the device
you want to add the type in the
name and use „Next” button.
Example:
For radio controlled Roller Shutter motor, we take a
traditional remote already added to the motor and
we press the „PROG/P2” button. The motor will
respond by emitting sound and moving up and
down, press the „PROG/P2” button again – the
motor will respond with sound. Then in the mobile
app press the „Prog” button – motor will respond
with sound and up and down move. The device is
added.
The function button will appear on the screen. The buttons
works similar to buttons on the traditional remote control. The
device we would like to add to the Central Unit has to put in to
programming mode with use of the traditional remote or by
switching off and on the powers supply. Next we use the buttons
in the mobile app the same way we use traditional remote we
would like to add.
Otros manuales para SmartControl ZSC1
1
Tabla de contenidos
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario