Zeiss Opmi lumera 700 Guía de instalación

Lumera ®700

Basic Instructions

Attention: Refer to the User Manual for additional warnings, safety information, labeling and detailed operating instructions.

This basic instruction sheet is only a complement to the User manual (G-30-1673-en).

Switch the power on by pressing the on/off switch

This will be on the wall for a ceiling mounted microscope, or on the base unit for a floor mounted microscope.

Foot Pedal:

Once the microscope is booted up and showing the Main Menu, place the foot pedal horizontally flat on the floor in order to establish

a connection with the microscope. You should then see a symbol in the top right hand corner indicating the foot pedal is connected to

the microscope and the amount of power left in the battery.

The foot pedal should be hung up on the appropriate bar when not used to maintain battery power for a long as possible.

IF THE FOOT PEDAL POWER SHOULD FAIL, ATTACH TO THE MICROSCOPE USING THE CABLE PROVIDED.

Activate User Profile

The microscope will default to the last user profile used. Check it is the correct one for each surgeon.

To change to a different user, click on User in the main Menu, click the drop down box under User and select the user

required. Once selected click the Activate icon at the bottom. If you do not the microscope will default to the previous user

and their profile.

Refer to:

Version 8.1

Page 194

G-30-1673-en

Configure User Settings

Set Up Profile

In the User Menu, click on the paper with the + symbol to enter a Surgeon Name, then click save icon at the bottom.

Then on the Surgery Profile Icon, select Anterior or Posterior. Lastly click Activate icon at the bottom.

Only if using Posterior with RESIGHT, click on the configuration (spanner) icon, then click on Posterior profile icon and finally click on the “R” to

link the RESIGHT into the posterior profile. Click save icon at the bottom. Posterior profile will now activate whenever RESIGHT is positioned

under the microscope.

Light Settings



In the main menu, click on Light icon, then click OPMI light icon. The light intensity can then be adjusted on the left hand side with the up

and down arrow icons.



The Red Reflex to Full Field can also be adjusted on the horizontal bar using the left and right arrow keys. On this bar position 1 indicates

full red reflex and position 3 no red reflex. Click save icon once finished.



Always use the minimum light intensity possible

Excessive light intensity or long radiation exposure times

may lead to retinal injury in the patient's eye

Refer to:

Version 8.1

Page 178 G-30-

1673-en

Refer to:

Version 8.1

Page 184

G-30-1673-

Carl Zeiss Ltd

Customercare.uk@zeiss.com

01223 401450

Version 8.1

Page 234

G-30-1673-

Trouble Shooting

If the foot pedal has difficulties connecting, either use the cable provided to connect to the microscope directly, or in the Main Menu click on tab 2

and then system settings and click on the Pairing Icon.

The following may have been altered if you are having problems manoeuvring your microscope:

Blank screen. The I button may have been touched in error next to the on/off switch.

To return to a surgeon’s default setting, press the reset button situated above the overhead display.

To preserve the lamp life turn off the microscope by moving it upwards until it beeps. To turn on again just lower it slightly and it will turn on again.

Shut-down |

Turn off the microscope by the main power switch as before.

Version 8.1

Page 218

G-30-1673-

Version 8.1

Page 227

G-30-1673-

Version 8.1

G-30-1673-

en Page

203

Foot Control Panel

In the Main Menu, open the Additional Settings, then select Foot Control Panel

Each button on the panel can then be clicked on and assigned a specific function.

Once the foot control panel has been optimized to the surgeon’s preferences, click the save icon at the bottom.

Hand Grip



In the Main Menu, open the Additional Settings, then select Handgrip



Each button on the panel can then be clicked on and assigned a specific function.



Once the handgrip has been optimized to the surgeon’s preferences, click the save icon at the bottom.

Overhead Display



In the Main Menu, open the Additional Settings, then select Overhead Display



Switch on Overhead Display and adjust brightness by using up and down arrows on left hand side.



Click Save Icon at the bottom

Camera Settings



In the Main Menu, click on the Camera Icon, then click on White Balance.



This creates a prompt for you to hold a plain white paper under the microscope to perform the white balance.



Tabs 2 and 3 of the camera page allow customization of brightness and colour values.

Configure (optional)



In the Main Menu, select tab 2 and click on System Settings. Then click on the Recording Icon. On this tab the image format can be changed

to JPG or Tiff. On tab 2 storage of recordings can be selected to USB or Network. Click save icon on the bottom after any changes made.

Recording



In order to record images or videos, click on the Recording Icon in the Main Menu.



Then click on the Change button on the top right corner to input patient details.



Lastly select image or video icon.



Video can then be controlled with the icons at the bottom.

Video Recording

Version

8.1 Page

214 G-

30-1673-

Otros manuales para opmi lumera 700

Tabla de contenidos

Otros manuales de Microscopio de Zeiss

Zeiss

Zeiss LSM800-6 Manual de usuario

Zeiss

Zeiss Axioplan 2 imaging and Axiophot 2 Manual de usuario

Zeiss

Zeiss Primovert Manual de usuario

Zeiss

Zeiss SIGMA Series Manual de usuario

Zeiss

Zeiss OPMI PRO magis Manual de usuario

Zeiss

Zeiss Axioskop Manual de usuario

Zeiss

Zeiss LSM 710 SIM Manual de usuario

Zeiss

Zeiss Axioscope 7 Manual de usuario

Zeiss

Zeiss Axiocam MR Manual de instalación y funcionamiento

Zeiss

Zeiss Axioscope 5 Manual de usuario

Zeiss

Zeiss LSM 710 Manual de usuario

Zeiss

Zeiss Axioskop Manual de usuario

Zeiss

Zeiss Axioskop 2 Manual de usuario

Zeiss

Zeiss LSM 800 Manual de usuario

Zeiss

Zeiss Stemi 305 cam Manual de usuario

Zeiss

Zeiss Mechanical stage S mot. Manual de usuario

Zeiss

Zeiss VISU 200 Manual de usuario

Zeiss

Zeiss OPMI PROergo S7 Manual de usuario

Zeiss

Zeiss LSM 710 Manual de usuario

Zeiss

Zeiss LSM 880 Manual de usuario

Zeiss

Zeiss Axio Scope.A1 Manual de usuario

Zeiss

Zeiss OPMI 1FR XY Manual de usuario

Zeiss

Zeiss LSM 880 Manual de usuario

Zeiss

Zeiss LSM 510 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario

Zeiss opmi lumera 700 Guía de instalación

Manuales populares de Microscopio de otras marcas