Zeiss OPMI Pentero Guía de referencia

OPMI®Pentero®

Software Release 2.2

Brief instructions

G-30-1702-en

Issue2.0

Printed on 17. 03. 2008

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Contents

Key to symbols Page 3

Powering up and positioning the system Page 4

Positioning the microscope Page 5

Attaching sterile drapes Page 6

Balancing the system Page 7

Central user interface (touchscreen) Page 8

Menu structure Page 9

Illumination Page 10

Lamp change

Changing the lamp module

Page 11

Adjusting the position of the handgrips Page 12

Configuring the handgrips Page 13

Configuring the foot control panel Page 14

Mounting the tube and eyepieces Page 15

Attaching documentation / coobservation equipment Page 16

Adjusting the tubes and eyepieces Page 17

Setting the eyepieces (compensation for ametropia) Page 18

Setting the adjustment speeds of focus and zoom Page 19

OR layout drawings Page 20

Exporting patient data to CD/DVD/USB/DICOM Page 22

Connecting an external monitor Page 24

What to do in an emergency - brief instructions Page 26

Lamp change during power failure

Failure of the zoom function

Failure of the focusing function

Failure of the magnetic brakes

Failure of the touchscreen

Failure of the line voltage

Error messages in the data injection system and on the touchscreen

Failure of all control functions (Emergency mode)

Blocking of individual magnetic brakes

Page 28

Page 30

Page 31

Page 32

Page 33

Page 34

Page 35

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Caution:

These brief instructions are only an excerpt from the complete user

manual. They cannot replace the detailed description provided in

the user manual.

Therefore, make yourself thoroughly familiar with the comments

and warning notes included in the complete user manual G-30-1458.

Key to symbols

Different symbols used in this manual draw your attention to safety as-

pects and useful tips. These symbols are explained in the following.

Warning!

The warning triangle indicates potential sources of danger which may

constitute a risk of injury for the user or a health hazard.

Caution:

The square indicates situations which may lead to malfunction, defects,

collision or damage of the system.

Note:

The hand indicates hints on the use of the system or other tips for the

user.

Read the user manual!

OPMI®and Pentero®are registered trademarks of Carl Zeiss Surgical

GmbH.

AutoDrape™, Superlux, FlexiTrack™ and MultiVision™ are trade-

marks of Carl Zeiss Surgical GmbH.

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Switching on the system

Warning!

– The correct use of the system is absolutely vital for safe operation.

Therefore, please thoroughly familiarize yourself with the content of

user manual G-30-1458 before starting up the system.

– Before starting, make sure to read the chapters "Safety" and "Prepa-

rations for use" of the user manual!

OPMIPentero

On / Off

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Positioning the microscope

Warning!

For safety reasons, the system must only be used when correctly bal-

anced.

Before starting, make sure to read the chapter "Preparations for use" of

the user manual!

• Press the brake release buttons (AB) to unlock all magnetic brakes.

Keep the brake release buttons (AB) pressed and move the ceiling

mount into the working position required using the handgrips. When

you let go of the brake release buttons (AB), all magnetic brakes are

locked.

G-30-1458

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Positioning the system at the operating table

The stand is provided with a handle which allows the reliable and easy

guidance of the system during relocation. Please only use this handle for

this purpose.

The stand base is equipped with the new FlexiTrak technology which

makes it considerably easier for you to move and position the system in

the OR. Two additional pedals on the base allow you to conveniently se-

lect the required condition of the stand:

– None of the pedals has been pressed:

Exact and sensitive positioning in the OR and at the operating table in

all directions with a minimum of effort.

– Right-hand pedal (2) is pressed down hard until it snaps in:

Reliable and precise straight-ahead movement, also over low thresh-

olds (elevator). Press this pedal until it snaps in to set the two front

casters for straight-ahead travel. The other casters remain steerable.

When you slightly press pedal (1), all four casters will be steerable

again.

– Pressing left-hand pedal (1) to the stop will lock the stand base in po-

sition, preventing it from inadvertently rolling away. After the system

has been finally positioned at the operating table, you should step on

this pedal.

3Possible positions for cranial procedures

4Possible positions for face-to-face procedures (spine)

5 Surgeon

6 Assistant

Note:

The system allows overhead positioning and can therefore be placed in

any position behind the surgeon or assistant.

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Attaching sterile drapes

Caution:

When attaching the drape, please ensure that there is sufficient space for

the tilt and rotation movements of the surgical microscope.

DRAPE

Hier luftdicht abschließen

Make airtight here

Fermer hermétiquement ici

Cerrar hermélicamente aqui

Effective range

of drape vacuum system

Sterile area

Non-sterile

area

PHOTO

AUTOBALANCE

PAT-FILES

USER

REC START

VOICE CTRL

DICTATION

TELEPHONE

FREEZE

FULL SCREEN

FOCUS

359 mm

LIGHT

33%

ZOOM

5.9x

FOCUS

SPEED

ZOOM

SPEED

LIGHT

INTENSITY

DRAPE

CONFIG

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Balancing the system

Warning!

Make sure to observe the instructions in the chapter "Balancing the

system" of user manual G-30-1458.

For safety reasons, the system must only be used when correctly bal-

anced. Despite the autobalance function, it may happen in exceptional

cases that the surgical microscope is not correctly balanced.

With an incorrectly balanced system, brake release may lead to uncon-

trolled movements of the suspension system. For this reason, the bal-

ancing procedure and the subsequent test must not be performed above

the patient and only at a safe distance from other persons and devices.

• Hold the microscope tightly at both handgrips.

• Unlock the magnetic brakes (AB) and swing out the microscope until

indicator (1) is centered in the blue area (2). Then you can perform the

"Autobalance Complete System" procedure.

Fine adjustment for mouth switch

G-30-1458

PHOTO

DRAPE

FREEZE

Autobalance Complete System

MENU START

START

Autobalance Microscope

Drape Compensation

Autobalance

30. 01. 04 17:56

User:

XXXXXXXX

Patient:

XXXXXXX

Recorder Capacity:

Int:.......% Ext:.........%

USER

VOICE CTRL

DICTATION

TELEPHONE

FULL SCREEN

CONFIG

PAT-FILES

Fine adjustment mouth switch

-3

REC START

STOP

AUTOBALANCE

G-30-1702-en OPMI® Pentero® Software Release 2.2 Issue 2.0

Printed on 17. 03. 2008

Central user interface (touchscreen)

Note:

For detailed information on the submenus and their configuration, please

see user manual G-30-1458.

USER CONFIG

Start

PAT-FILES

Otros manuales para OPMI Pentero

Tabla de contenidos

Otros manuales de Equipo médico de Zeiss

Zeiss

Zeiss S7 / OPMI VISU 160 Manual de usuario

Zeiss

Zeiss ACCURA Manual de usuario

Zeiss

Zeiss VISULAS 532s Manual del operador

Zeiss

Zeiss CT LUCIA Series Manual de usuario

Zeiss

Zeiss VISULAS YAG III Manual de usuario

Zeiss

Zeiss ATLAS 9000 Manual de usuario

Zeiss

Zeiss PLEX Elite 9000 Manual de usuario

Zeiss

Zeiss KSK 150 FC Manual de usuario

Zeiss

Zeiss 3000 Manual de usuario

Zeiss

Zeiss OPMI Lumera i Manual de usuario

Zeiss

Zeiss GeminiSEM Series Manual de usuario

Zeiss

Zeiss IOLMaster 700 Manual de usuario

Zeiss

Zeiss Stratus OCT 3000 Manual de usuario

Zeiss

Zeiss OPMI Lumera T Manual de usuario

Zeiss

Zeiss ATLAS 9000 Manual de usuario

Zeiss

Zeiss Focal CC Manual de usuario

Zeiss

Zeiss opmi lumera 700 Manual de usuario

Zeiss

Zeiss SL 120 Manual del operador

Zeiss

Zeiss DuraMax Manual de usuario

Zeiss

Zeiss MultiSEM 505 Series Manual de usuario

Zeiss

Zeiss OPMI Lumera T Manual de usuario

Zeiss

Zeiss EXTARO 300 Manual de usuario

Zeiss

Zeiss IOLMaster 500 Manual de usuario

Zeiss

Zeiss HFA3 Manual de usuario

Manuales populares de Equipo médico de otras marcas

TekTone

TekTone Tek-CARE160 Manual de usuario

NeuroMetrix

NeuroMetrix Quell 2.0 Manual de usuario

AMT

AMT XLR8 Manual de usuario

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manual de usuario

EDAN

EDAN SONOTRAX Pro Manual de usuario

Restorative Therapies

Restorative Therapies RT300 Manual de usuario

Gendex

Gendex Expert DC Manual de usuario

Dexcowin

Dexcowin ADX4000W Manual de usuario

Libelium

Libelium MySignals Manual de usuario

Acelity

Acelity V.A.C.ULTA 4 Manual de usuario

Caputron

Caputron ActivaDose II tDCS Manual de usuario

FujiFilm

FujiFilm Sonart Manual del propietario

Plinth 2000

Plinth 2000 93CDT Manual de usuario

GE SENOGRAPHE 800T Manual de usuario

GE Definium 5000 Manual de usuario

Kanmed

Kanmed GE-1380 Manual de usuario

Huntleigh

Huntleigh FD1 Manual de usuario

Stryker

Stryker SPR Plus Manual de usuario