Zcom AS220V2 Manual de usuario

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Package Contents

One indoor

access point

One mounting bracket

+ one screw

Two mounting bracket screws

+ screw anchors

One

allen wrench

One quick start guide

Note: If any of the items, mentioned above, are not included in the packaging or are

damaged in any way, contact your reseller immediately.

Installation Requirements

(STP) cabling. It is the professional installer’s responsibility to follow local country regulations,

including operation within legal frequency channels, output power, indoor cabling requirements,

and Dynamic Frequency Selection (DFS) requirements.

Mounting the Access Point

In-wall mount

Determine where you want to mount the device, position the socket into the slot.

Insert the mounting bracket into the socket using

the two screws (included in the packaging).

Slide the device onto the mounting

bracket to finish the installation.

Note: Before lock two screws into the socket, please reserve space up to 15 cm in length

above bracket for installation.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Wall mount

Determine where you want to mount the device, position the mounting bracket onto the wall,

and use a marker to mark the two screw holes on the wall.

Note: Before drill two holes into the wall, please reserve space up to 15 cm in length

above bracket for installation.

Drill the two holes into the wall and insert the two screw anchors (included in the packaging)

into the holes.

Install the mounting bracket onto the wall

using the two screws (included in the

packaging) into the screw plugs in the wall.

Slide the device onto the mounting bracket

to finish the installation.

Ceiling Mount (Optional accessory_AS-CLM4)

Determine where you want to mount the device, position the mounting bracket onto the ceiling

board.

Use a marker to locate the two screw holes on the ceiling, and drill the two holes into the ceiling.

Note: The thickness of ceiling board should be less than 15mm.

Insert the ceiling screw through the mounting

bracket, ceiling board, and ceiling mount as the

following picture.

Slide the device onto the mounting bracket

to finish the installation.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Installing the Anti-tamper Lock (Optional accessory_AS-LK18)

Slide all the cables through their respective holes on the anti-tamper lock.

Install the mounting bracket; plug all the

cables into their respective ports on the

device before installing the anti-tamper lock.

Position the anti-tamper lock onto the

device and fasten the lock screw clock-wise

with special anti-tamper lock key.

Safety Notice

1. Do not install the device close to any electrical grounding device or lightning protection system.

Place the device’s own grounding and lightning protection system apart from any electrical

grounding device and lightning protection system as far as possible.

2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the

power adapter by its edge and do not touch any component or printed circuit boards,

especially for module device.

3. Make sure to keep the temperature and humidity of the installation location at an optimal

level.

4. An excellent grounding system guarantees the stable operation of device, as well as to protect

device from lightning, interference and electrostatic discharges.

5. If installed outdoors, the device may be damaged by lightning. We recommend that you install

additional lightning protection devices if necessary, considering the conditions in your area.

6. Supply stable power to the device. Unstable power may cause the device to malfunction. The

device supports PoE power supply and is recommended if the device is installed near grid lines

within less than 100 meters radius.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Powering the Access Point

Connect to the WAN/PoE IN Port

Connect the PoE cable into the WAN/PoE IN

port of the device, then it will power on.

Connect to a power adapter

(Optional accessory_ AC-48052)

Connect the power adaptor into the DC port

of the device, then it will power on.

LED Indicator

Color

Behavior

Description

Red

Solid

Initializing

Blinking

Factory defaults, waiting to be integrated

Blue

Blinking

Device is busy updating its firmware; do not touch or unplug it

Green

Solid

Ethernet connection detected

Blinking

No Ethernet connection detected

Access Point Configuration

In a default access point configuration is TAP mode; the access point uses a DHCP client IP address.

Step 1. Make sure DHCP is enabled on the network. The access point must receive its IP address

through DHCP.

Note: Switching from DHCP to assign a static IP address or DNS and L2 discovery mode

to the access point, please refer to the user manual for more information.

https://www.zcom.com.tw/index/downloads

Step 2. Power on the access point. As the access point attempts to connect to the Wireless LAN

Controller (WLC), the status LED indicator blinks green. If the connection is successful, the

status LED indicator is steady green.

Step 3. If the access point cannot connect to the WLC by DHCP broadcast, please refer to the

Note: It's available to turn on the access point by either or .

Note: It is equipped with a secondary LAN/ PoE (Power Over Ethernet) out to power a

device such as an IP phone, a security camera, or another AS220V2. The input power

should be 802.3at (PoE+) standard, and the maximum output power of the PoE is 13

Watts.

Note: Do NOT attempt to connect any non-passive PoE devices to LAN port when PoE

pass-through is enabled. Otherwise the initial voltage may damage the powered device.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

following optional settings.

Optional: Set up the access point by your computer

Note: The following procedure assumes that Windows 10 is the operating system.

Procedures for other operating systems are similar.

Step 1. On your computer, configure your network adapter from the “Local Area Connection”

settings as follows:

˙StartControl PanelNetwork and Sharing CenterChange Adapter Settings

Step 2. Edit the TCP/IPv4 address setting as follows:

˙Local Area ConnectionPropertiesInternet Protocol Version 4(TCP/IPv4)

Properties

Note: Record all of the currently active settings so you can restore your computer to its

current configuration later (when this process is complete.)

Step 3. Select “Use the following IP address”and make the following entries:

˙IP address: 192.168.1.168 (or any available address in the 192.168.1.x network, except

192.168.1.1)

˙Subnet mask: 255.255.255.0

Leave the “Default gateway”and “DNS server”fields empty.

Step 4. Click “OK”to save your changes.

Step 1. Launch a Web browser; type 192.168.1.1 URL to connect to the access point. When a

security alert dialog box appears, click OK/Yes to proceed.

Step 2. When login page appears, enter the following: Username: root/Password: password

Step 3. Click login.

Customizing the Wireless Settings

On the Web interface menu, Select StatusGeneral in the menu bar. Check your switchmod item

to select “Connect with via IP”, and setup your WLC IP address on “Wireless Switch Address 1”.

Note: In TAP mode, the access point must be able to go with WLCs for bulk configuration

and performing other commands of access points. Please refer to WLC QSG for more

information. https://www.zcom.com.tw/index/downloads

Note: If you need a standalone access point, please refer to the FAP mode configuration.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

FAP Mode

The default AP mode is TAP mode, before FAP configurations please change AP mode.

Step 1. If currently in TAP Mode: On the Web interface menu, click SystemAP mode.

Step 2. Select Fat AP from the drop-down list.

Step 3. Click save & apply to take effect.

Note: For FAP mode, please refer to the user manual for more information.

https://www.zcom.com.tw/index/downloads

Wi-Fi SON

Z-COM Wi-Fi SON accelerates the connection between devices, providing users a quick installation

and easy deployment capabilities. Please refer to the user manual for more information.

https://www.zcom.com.tw/index/downloads

Mobile APP

Z-COM offers the App for bridge mode settings, which is available from our website:

https://www.zcom.com.tw/index/downloads. Please research and download it to provision.

If necessary: reset button

If the access point needs to be reset, please press and

hold the reset button for more than ten seconds to

restore to factory default settings.

Technical Specifications

Physical

Dimensions

(L x W x H)

96 x 29.9 x 192 mm

(3.78 x 1.18 x 7.56 in)

WAN/PoE In Port

One 10/100/1000 Mbps port

Weight

500 grams (1.1 lbs.)

LAN/PoE Out Port

One 10/100/1000 Mbps port

Antenna

2.4GHz: Embedded 2dBi omni antennas

5GHz: Embedded 2.5dBi omni antennas

Power Supply

DC 48V, 0.5A PoE, or DC Jack (optional accessory)

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Physical

LAN/PoE Out

48V/13 Watts (Max.), Passive PoE (Pairs 4, 5+; 7, 8 Return)

Power Consumption

Max. 12 Watts

Environmental

Temperature

Humidity

Operating

-10°C to 60°C (14°F to 140°F)

10% to 90% (Non-condensing)

Storage

-20°C to 70°C (-4°F to 158°F)

10% to 90% (Non-condensing)

Compliance Information

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a separation distance of at least

20 cm from all persons and must not be located or operating in conjunction with any other

antenna or transmitter.

CE Marking

CE marking on this product represents the product is in compliance with all directives that are

applicable to it.

Note: This device meets Max. TX power limit per ETSI regulations.

Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz

frequency range within all member states.

RoHS/WEEE Compliance Statement

European Directive 2012/19/EU requires that the equipment bearing this symbol on the product

and/ or its packaging must not be disposed of with unsorted municipal waste. The symbol

indicates that this product should be disposed of separately from regular household waste streams.

It is your responsibility to dispose of this and other electric and electronic equipment via

designated collection facilities appointed by the government or local authorities. Correct disposal

and recycling will help prevent potential negative consequences to the environment and human

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

health. For more detailed information about the disposal of your old equipment, please contact

your local authorities, waste disposal service, or the shop where you purchased the product.

Declaration of Conformity

Hereby, Z-COM, Inc. declares that the radio equipment type AS220V2 is in compliance with

Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following

internet address: https://www.zcom.com.tw/index/downloads

Optional Accessories

Item

Picture

AS-CLM4

Ceiling mount + two screws

AS-LK18

Anti-tamper Lock

AC-48052

48 V 0.52A power adapter

Contact Information

All information may be changed by Z-COM at any time without prior notice or explanation to the

user. For further information please refer to our website: www.zcom.com.tw

Otros manuales para AS220V2

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Zcom

Zcom

Zcom SP230 Series Manual de usuario

Zcom

Zcom ZAC-1023-2-9 Manual de usuario

Zcom

Zcom SP220V2 Series Manual de usuario

Zcom

Zcom AC-1028 Manual de usuario

Zcom

Zcom SP420 Series Manual de usuario

Zcom

Zcom ZAC Series Manual de usuario

Zcom

Zcom SP230 Series Manual de usuario

Zcom

Zcom ZAC Series Manual de usuario

Zcom

Zcom AS220V2 Manual de usuario

Zcom

Zcom XV-5850 Manual de usuario

Zcom

Zcom AS420 Manual de usuario

Zcom

Zcom ZN-7100-DE500-G V4 Manual de usuario

Zcom

Zcom AC-1025D Manual de usuario

Zcom

Zcom XG-1020 Manual de usuario

Zcom

Zcom XG-3120 Manual de usuario

Zcom

Zcom SP230 Series Manual de usuario

Zcom

Zcom ZAC-1023-5 Manual de usuario

Zcom

Zcom AC-1031 Manual de usuario

Zcom

Zcom AS220V2 Manual de usuario

Zcom

Zcom SP250 Manual de usuario

Zcom

Zcom ZCN-1523H-2-8 Manual de usuario

Zcom

Zcom ZAC-1023-2 Manual de usuario

Zcom

Zcom XG-580 PLUS Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario