Zapp Z020 Manual de usuario
Z020 – EVDO Modem
User Manual
V6.1
2007.07.30
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 2/48
AnyDATA CDMA Module Series Reference Design Specification
Copyright © 2000~2007 AnyDATA Corp. All Rights Reserved.
Any part of this document may not be distributed, communicated, reproduced or transmitted in any form
or by any means, electronic or mechanical or otherwise, for any purpose, without the permission of
AnyDATA Corp.
This document can be subjected to revision without further notice.
Contact Address
AnyData.Net Inc.(Korea)
DaeGo Bldg, 8th., 1591-10
Kwanyang-dong, Dongan_gu,
Anyang City, Kyunggi-do Korea.
http://www.anydata.co.kr
Rep:+82-31-380-7100
Fax:+82-31-476-6021
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 3/48
Contents
1. Getting Started.....................................................................................................................................4
1.1 USB Modem.....................................................................................................................................5
1.2 Components ....................................................................................................................................7
1.3 LED indicator...................................................................................................................................7
2. Program Installation............................................................................................................................8
2.1 Introduction .....................................................................................................................................8
2.2 Minimum System Requirement......................................................................................................8
2.2.1 PC Hardware...........................................................................................................................8
2.2.2 Operating System ..................................................................................................................8
2.3 USB Driver Installation and Uninstall (Windows XP/2000)..........................................................9
2.3.1 USB Driver Installation (Automatic).....................................................................................9
2.3.2 USB Driver Installation (Manual) ........................................................................................12
2.3.3 USB Driver Uninstall............................................................................................................18
2.4 USB Driver Installation and Uninstall (Windows Vista).............................................................20
2.4.1 USB Driver Installation (Automatic)...................................................................................20
2.4.2 USB Driver Installation (Manual) ........................................................................................23
2.4.3 USB Driver Uninstall............................................................................................................30
2.5 Installing Zapp Online Express Software ...................................................................................32
3. Using Zapp Online Express Program..............................................................................................37
3.1 Running the program....................................................................................................................37
3.2 Exiting the program ......................................................................................................................38
3.3 Screen Display of Zapp Online Express.....................................................................................39
3.3.1 Executed Screen..................................................................................................................39
3.3.2 Description of each icon .....................................................................................................40
3.4 Connecting to the Internet ...........................................................................................................43
3.5 Disconnecting from the Internet..................................................................................................44
3.6 Sending and Receiving calls........................................................................................................44
3.7 Viewing received or saved message...........................................................................................45
4. Troubleshooting.................................................................................................................................46
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 4/48
1. Getting Started
In order to use Z020 USB MODEM following must be satisfied:
1) Zapp Online Software and Z020 USB MODEM Driver has been installed
on the computer.
2) The Z020 EVDO modem is active (the activation process has been successfully completed – this
is indicated by POWER LED in green colour, and then by the restart of the modem).
<CAUTION> PLEASE CONNECT THE BATTERY AND EXTERNAL POWER SUPPLY TO INSURE MAXIMUM
PERFORMANCE OF THE MODEM. IF USING THE MODEM WHILE ON-THE-ROAD, PLEASE
KEEP BATTERY INTACTED WITH THE MODEM. AND MAKE SURE THE BATTEY IS FULLY
CHARGED BEFORE THE USAGE. WHEN THE BATTEY CAPACITY IS LOW, MAKE SURE TO
CHARGE IT BEFORE CONTINUING TO USE.
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 5/48
1.1 USB Modem
+5V DC POWER JACK Mini USB Port EAR JACK
LED POWER KEY
INTERNALANTENNA
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 6/48
<Caution>
When dismounting the battery, push the bottom of modem upward to slide easily out from the battery cradle.
External Antenna Port
Battery Contact Pins
Battery (optional)
Contact Switch
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 7/48
1.2 Components
5VDCPowerAdaptor StandardUSBCable
1.3 LED indicator
POWER
Mode Descriptions
BLUE Battery power is used
BLUE BLINK Low battery warning
RED External DC power is used and fully charged
VIOLET External DC power is used and under charging
OFF Power off
IDLE
Mode Descriptions
BLUE Working in EVDO network
BLUE BLINK Searching EVDO network
OFF Service is not available
BUSY
Mode Descriptions
BLUE - EVDO : Data throughput exceed to 1,200Kbps
CYAN - EVDO : Data throughput between 600Kbps to 1,200Kbps
GREEN - EVDO : Data throughput under 600Kbps
GREEN BLINK - EVDO : Outgoing call initiated but still attempt
OFF - EVDO : Not in connected state
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 8/48
2. Program Installation
2.1 Introduction
This section describes step-by-step method to install Z020 USB MODEM and
Zapp Online Express Software.
<Note>
Must install the software before connecting Z020 USB MODEM to PC/Notebook.
2.2 Minimum System Requirement
2.2.1 PC Hardware
Recommend to use PC/Notebook at speed of 300 MHz or higher.
Minimum 233 MHz speed required, * Intel Pentium/Celeron products,
AMD K6/Athlon/Duron products or compatible processors
Recommend to use 128MB RAM or higher
Minimum 64MB of memory must be used,
but in this case the performance will be degraded and certain features will be limited.
At least 100 MB of free hard disk space is required.
Motherboard or PCI card that supports USB.
Video adaptor with Super VGA (800 x 600) or higher resolution and Monitor
CD-ROM or DVD Optical Drive
Keyboard and Mouse
2.2.2 Operating System
Windows XP Home or Professional (with Service Pack 2)
Windows 2000 (with Service Pack 4 for optimal performances)
Windows Vista
< Recommended parameters >
Windows Update : Keep your computer up to date
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 9/48
2.3 USB Driver Installation and Uninstall (Windows XP/2000)
2.3.1 USB Driver Installation (Automatic)
1. The installation of the USB Wireless Modem Connect should run automatically upon selecting this
option on the menu of the Installation CD. Click ”Install Modem Driver” on the menu.
Z020 – EVDO Modem(User Manual)
Zapp–TheNextGenerationNetwork 10/48
2. The computer needs to restart after the driver installation completed.
To restart the computer later, select “I want to manually reboot later”.
Tabla de contenidos
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario