YOKOGAWA UTAdvanced UT52A Manual
Setup Procedure
UTAdvanced Quick Setting (pH Control)
TI 04L01L01-01EN
Foreword
The contents of this document are subject to change without prior notice as a result of improvements in performance or functionality.
Copying or reproduction by any means of all or any part of the contents of this document without permission is strictly prohibited.
Use of this document is at the users risk.
This document is subject to change without notice. TI 04L01L01-01EN
2011.12.16 1st Edition (YK)
Technical
Information
■Overview
This is an example of wiring and settings using the UTAdvanced Quick Setting function for "pH Control."
For more details, see the user's manual.
■Relevant models
Standard models of the UT52A and UT55A (if there are 2 types of pharmaceuticals, select the
heating/cooling model)
■System
■Wiring
Sampling can be controlled to interpolate dead time
Current input signal
4–20 mA
Current input signal
4–20 mA
Plant A waste liquid -->
Plant B waste liquid -->
Plant C waste liquid -->
Chemical dosing pump
pH meter
converter
0–14 pH
pH meter
sensor
Effluent
■Sampling control
■Nonlinear t
yp
e
Control gain is switched by the Gap Gain Control
function
Current input
4–20 mA
PV
Current
input
Power
supply －
＋
203
Current output
4–20 mA
＋
－
UT52A, UT55A Standard Models
pH meter
＋
－
Current
output
4–20 mA
PV
Transmission
output
2/4
This document is subject to change without notice. TI 04L01L01-01EN 2011.12.16-00
■Settings
To set the sample PID control, input type (4 to 20 mA), and current control output (4 to 20 mA), set the
parameters below.
(1) Select the desired parameter with the UP or DOWN key
(2) Press SET/ENTER (the setting value blinks)
(3) Change the setting with the UP or DOWN key
(4) Press SET/ENTER to set the new value (the setting value stops blinking but remains
bright)
●Redoing the Quick Setting
Once functions are configured with the Quick Setting, the Quick Setting function
will not appear after you restart. However, you can redo the Quick Setting by
following the procedure below.
(1) Set the Quick Setting parameter QSM to ON, and re-engage power
(2) Set the PV input type parameter IN to OFF, and re-engage power
Press SET/ENTER to accept the "YES" option.
Quick Setting starts
First, the control type parameter CNT appears.
Set the CNT (control type) to S-PI (sample PI control).
OFF is displayed for IN (the PV input type).
Set IN (PV input type) to current signal: 4–20
(4–20 = 4.00 to 20.00 mA).
Set UNIT (PV input unit) to – (none). If necessary, use the unit label "pH."
ＳＴＡＲＴ ＱＵＩＣＫ
ＳＥＴＴＩＮＧ
QSM YES
CONTRＯＬ ＴYPE
1.
2.
CNt S-PI
PV INPUT TYPE
3.
IN OFF
PV INPUT TYPE
4.
IN 4ー20
PV INPUT UNIT
5.
UNIt ー
Power
Quick Setting
start
3/4
This document is subject to change without notice. TI 04L01L01-01EN 2011.12.16-00
Set RH (maximum value of PV input range) to 20.00 mA (the initial value).
Set RL (minimum value of PV input range) to 4.00 mA (the initial value).
Set SDP (PV input scale decimal point position) to 2.
Set SH (maximum value of PV input scale) to 14.00 (pH).
Set SL (minimum value of PV input scale) to 0.00 (pH).
Set OT (output type selection) to 00.02: OUT terminal (current 4 to 20 mA).
Skip this parameter (not relevant).
Finally, EXIT is displayed. Select YES and press SET/ENTER to complete the
basic function setup and return to the operating screen. Or, you can select NO
to continue with the Quick Setting.
11.
13.
12.
10.
MAXIMUM
VALUE OF PV
INPUT RANGE
6.
RH 20.00
7.
FINISH
EXIt YES
MINIMUM
VALUE OF PV
INPUT RANGE
RL 4.00
CONTROL OUTPUT
CYCLE TIME
Cｔ30.0
OUTPUT TYPE
SELECTION
8.
0ｔ00.02
9.
SｄP2
SH 14.00
PV INPUT SCALE DECIMAL
POINT POSITION
MAXIMUM VALUE OF
PV INPUT SCALE
SL 0.00
MINIMUM VALUE OF
PV INPUT SCALE
11.
13.
12.
10.
MAXIMUM
VALUE OF PV
INPUT RANGE
6.
RH 20.00
7.
FINISH
EXIt YES
MINIMUM
VALUE OF PV
INPUT RANGE
RL 4.00
CONTROL OUTPUT
CYCLE TIME
Cｔ30.0
OUTPUT TYPE
SELECTION
8.
0ｔ00.02
9.
SｄP2
SH 14.00
PV INPUT SCALE DECIMAL
POINT POSITION
MAXIMUM VALUE OF
PV INPUT SCALE
SL 0.00
MINIMUM VALUE OF
PV INPUT SCALE
4/4
This document is subject to change without notice. TI 04L01L01-01EN 2011.12.16-00
Revision Information
Document name: Setup Procedure: UTAdvanced Quick Setting (pH Control)
Document number: TI 04L01L01-01EN
First edition: December, 2011
Newly released
Otros manuales para UTAdvanced UT52A
1
Este manual sirve para los siguientes modelos
1
Otros manuales de Controladores de YOKOGAWA
YOKOGAWA
YOKOGAWA Vitesse FA-M3V Manual de usuario
YOKOGAWA
YOKOGAWA UP150 Manual de usuario
YOKOGAWA
YOKOGAWA UT35A-L Manual de usuario
YOKOGAWA
YOKOGAWA AQ2201 Manual de usuario
YOKOGAWA
YOKOGAWA UT52A/MDL series Manual de usuario
YOKOGAWA
YOKOGAWA YS170 Manual de usuario
YOKOGAWA
YOKOGAWA UT520 Manual de usuario
YOKOGAWA
YOKOGAWA CX1000 Manual de usuario
YOKOGAWA
YOKOGAWA FA-M3 Vitesse Manual de funcionamiento
YOKOGAWA
YOKOGAWA SMARTDAC+ GX20 Manual de usuario
YOKOGAWA
YOKOGAWA UT350 Manual de usuario
YOKOGAWA
YOKOGAWA UT32A-D Manual de usuario
YOKOGAWA
YOKOGAWA UT35A-L Manual de usuario
YOKOGAWA
YOKOGAWA UTAdvanced UT32A Manual
YOKOGAWA
YOKOGAWA UT Advanced UT32A Manual de usuario
YOKOGAWA
YOKOGAWA YS1000 Series Manual de usuario
YOKOGAWA
YOKOGAWA YS1000 Series Manual de usuario
YOKOGAWA
YOKOGAWA UT150L Manual de usuario
YOKOGAWA
YOKOGAWA FA-M3 Vitesse Manual de instalación y operación
YOKOGAWA
YOKOGAWA UTAdvanced UT32A Manual
