Yeti SB130/LR Manual de usuario
3.4.
BRAND OVERVIEW 05
FRAME FEATURES 07
GEOMETRY 09
MAINTENANCE SCHEDULE 11
TECHNICAL
ASSEMBLY OVERVIEW 17
EXPLODED VIEWS
REBUILD KITS 6
LEGAL
WARRANTY 35
CONTACT INFORMATION 36
7
TABLE OF CONTENTS
5.6.
CONGRATULATIONS ONYOUR PURCHASE OF A NEW YETI. We are confident your new bicycle will
exceed your expectations for value,
performance, and ride quality. Each
frameset and component has been custom
specified and designed to enhance your
riding experience. Whether you are a
beginner cyclist, or a seasoned pro, your Yeti
bicycle will provide endless hours of two-
wheeled fun.
This model specific manual is designed to
be used in conjunction with the general Yeti
Owner’s Manual and the manuals supplied
by the suspension manufacturers. If you did
not receive the Yeti owner’s manual or the
manual provided by the suspension
manufacturer, download the materials off
the Internet, or contact your local dealer.
Bicycling can be a hazardous activity
even under the best of circumstances.
Proper maintenance of your bicycle is your
responsibility and when done properly helps
reduce the risk of injury and damage to your
bicycle.
This manual outlines basic setup and
maintenance recommendations of your new
Yeti. Because it is impossible to anticipate
every situation or condition that may occur
during the assembly, setup, and
maintenance of your bicycle, Yeti
recommends that all service and repairs be
performed by your local authorized Yeti
Dealer.
This manual contains many “Warnings” and
“Cautions” concerning the consequences of
failure to maintain or inspect your bicycle.
The word “Warning” indicates a potentially
hazardous situation in which , if not
avoided, could result in serious injury or
death. The word “Caution” indicates a
potentially hazardous situation in which, if
not avoided may result in minor injuries or
damage to your bicycle or a component of
your bicycle. Be sure to read and
understand all of the Warnings and
Cautions listed in the manual.
Warning: Make sure you review and understand the warnings, instructions, and content of this manual and accompanying
manuals for your bicycle.
Warning: Technological advances have made bicycles and bicycle components more complex and the pace of innovation
is increasing. It is impossible for this manual or the accompanying manuals to provide all the information required to
properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have
work performed by an authorized Yeti retailer.
7.8.
1. The SB130 delivers 130 mm (137mm for SB130 LR)of travel with our
patented Switch Infinity Technology. Efficient pedaling performance
while still smooth and continuous when the going gets rough.
. High modulus carbon provides a stiff, strong and light weight chassis.
3. Colleted pivot axles help create a stiff interface between the front
and rear triangles of the frame. Custom Enduro Max sealed
bearings keep things moving freely at the pivots.
4. The SB130/LR does away with the front derailleur mount, making it
a 1x drive specific frame. This increases stiffness in the frame.
5. ISCG 05 chain guide mounts are included on the SB130/LR if case
you want to go for some extra drivetrain security in the rowdy
sections.
6. Using our integrated head tube on the SB130 allows for a larger
head tube with more area, increased stiffness, and lower overall
ride height without compromising any performance.
. The SB130 uses a 10 x 5.5mm Float shock, by Fox Racing Shox
8. Custom guards on the seat stay, chain stay and down tube
keep things quiet while riding and protect the frame.
9. The SB130/LR features internal routing for all cables, making the bike
quiet and clean looking as well as reducing cable rub on the paint.
Dedicated 12 x 148 Boost dropouts and integrated hanger with axle
threads for strength, stiffness, ease of hanger and wheel installation.
1. SWITCH INFINITY TECHNOLOGY PATENTED SUSPENSION SYSTEM
2. HIGH MODULUS CARBON FIBER MAIN FRAME AND SWING ARM
3. COLLET AXLE SYSTEM ON PIVOTS REDUCES BEARING WEAR
4. OPTIMIZED FOR 1X DRIVETRAINS ONL Y
5. ISCG 05 CHAINGUIDE MOUNTS
6. INTERATED EAD TUBE 41MM/5MM
7. SUSPENSION BY FOX
8. CUSTOM DEBRIS AND CHAIN SLAP GUARDS
9. INTERNAL CABLE ROUTING
10. INTEGRATED AXLE AND DERAILLEUR HANGER SYSTEM
10.
THE LOWDOWN ON THE SB130/LR ANDITS FEATURES. 10 x 55mm Float shock for SB130 LR.
9.10.
FITMEDIUM 5'5" (165 CM) - 5'11" (180 CM)
LARGE 5'10" (178 CM) - 6'3" (191 CM)
X-LARGE 6'1" (185 CM) - 6'7" (200 CM)
SMALL 5'1" (155 CM) - 5' " (10 CM)
M
B
L
I
J
O
C
N
H
G
E
F
D
A
K
MD LG XL
A 410 450 495
B EFF. TOP TUBE LENGTH 601.9 625.2 653.4
C HEAD TUBE ANGLE 65.5 65.5 65.5
D EFF. SEAT TUBE ANGLE 77.0 76.9 76.9
E CHAINSTAY LENGTH 433 433 433
F
SEAT TUBE LENGTH
1205.6 1230.2 1259.7
G EST. BB HEIGHT 337.7 337.7 337.7
H STANDOVER 725.9 728.2 730.6
I HEAD TUBE LENGTH 99.2 110.2 121.2
JAXLE TO CROWN 557.1 557.1 557.1
KFORK OFFSET 44 44 44
L
WHEELBASE
614.8
MREACH 460.2 480.2
NFRONT CENTER 772.6
O136.5 136.5 136.5
SM
380
570.7
65.5
77.1
433
1173.9
337.6
723.5
95.0
557.1
44
611.0
430.2
740.9
136.5
505.2
797.2 826.7
VERTICAL FORK TRAVEL
STACK 624.8 634.8
GEOMETRYFOX 36 / 150MM FORK
9.10.
FITMEDIUM 5'5" (165 CM) - 5'11" (180 CM)
LARGE 5'10" (178 CM) - 6'3" (191 CM)
X-LARGE 6'1" (185 CM) - 6'7" (200 CM)
SMALL 5'1" (155 CM) - 5' " (10 CM)
M
B
L
I
J
O
C
N
H
G
E
F
D
A
K
MD LG XL
A 410 450 495
B EFF. TOP TUBE LENGTH 603.4 626.7 655.0
C HEAD TUBE ANGLE 65.1 65.1 65.1
D EFF. SEAT TUBE ANGLE 76.6 76.5 76.4
E CHAINSTAY LENGTH 433.2 433.2 433.2
F
SEAT TUBE LENGTH
1209.8 1234.4 1263.9
G EST. BB HEIGHT 340.9 340.8 340.8
H STANDOVER 731.5 733.7 735.8
I HEAD TUBE LENGTH 99.2 110.2 121.2
JAXLE TO CROWN 567.1 567.1 567.1
KFORK OFFSET 44 44 44
L
WHEELBASE
618.3
MREACH 455.6 475.6
NFRONT CENTER 776.6
O145.1 145.1 145.1
SM
380
572.1
65.1
76.6
433.2
1178.1
341.0
729.3
95.0
567.1
44
614.3
425.5
744.8
145.1
500.6
801.1 830.7
VERTICAL FORK TRAVEL
STACK 628.4 638.5
GEOMETRYFOX 36 / 160MM FORK
11.12.
TOREYeti strongly recommends using a torque wrench when assembling your frame. Torque
specifications for individual parts on the SB130/LR are listed below, as well as in the
step by step assembly instructions later in the manual. For general bicycle maintenance
please consult the torque specifications of the component you are adjusting.
EY TORE SPECSPART NUMBER DESCRIPTION TORQUE (NM)
300040485 MAIN PIOT ALE 12
00003 SS PIOT BOLT, FEMALE 16
30003096 COLLET ALE 30.510.5 M101.0 13
300040454 COLLET WEDE BOLT, LARE 14
30003093 LIN, PIOT ARDWARE, MALE, 15MM 15
30006003 1148 DERAILLEUR ANER 10
30003005 SCS M6x1.0 0L, SWITC LIN MOUNT 1
300040486 COLLET WEDE BOLT, SMALL 8
100425006 AXLE, YETI BOLT ON, 12X148MM 12-15
300030151 BOLT, TI MALE, M6 X 12.0 MM 10
200020311 20
LOCRIN, 6902-2RS
WEEKLY
MONTHLY
3 MONTHS
ANNUALLY
CHECK TIRE PRESSURE
CLEAN BIKE OF MUD AND DEBRIS
CHECK BRAKE FUNCTION
CHECK SHOCK PRESSURE
CHECK FOR LOOSE BOLTS AND TIGHTEN, IF NECESSARY
CHECK HEADSET AND TIGHTEN / LOOSEN, IF NECESSARY
THOROUGHLY CLEAN PIVOT POINTS WITH A RAG (DO NOT LUBRICA TE)
LUBE INFINITY LINK EVERY 40 HRS. (YETI HEAVY MOLYBDENUM GREASE)
CHECK / REPLACE BRAKE PADS
CHECK TIRES FOR WEAR
CHECK SPOKE TENSION. RETENTION, IF NECESSARY
CHECK CHAIN FOR WEAR. REPLACE IF NECESSARY
COMPLETE TUNE-UP PERFORMED BY AN AUTHORIZED YETI DEALER
KEEP YOUR YETI FRESHAND CLEANOVERVIEWFollowing these guidelines will help maintain the performance of your bicycle and
prevent more serious problems from arising. It is important to remember that service
intervals can vary depending on climate, trail conditions and riding frequency. If you
are unsure about working on your own bicycle, contact your authorized Y eti Dealer for
more information on general bicycle maintenance.
SCHEDULECLEAN AND LUBE CHAIN
01.
With a 3mm allen key, remove the lower
cable port access cover near the bottom
bracket.
02.
Install your seatpost housing into the
head tube port, pushing until it exits near
the lower cable port access hole.
04.
While pushing the housing into the head
tube port, continue pushing the cable
up the seat tube through the access
port until the housing exits the seat
tube.
01.
Remove the lower cable port access
cover with a 3mm allen key.
02.
Drop a Park Tool Router tool down
the seat tube until it exits the access
port.
03.
Push your seatpost housing into the frame
from the headtube port until it exits near the
access port.
05.
Pull router tool back through the frame
until your housing exits the seat tube.
04.
Outside of the access port, connect
the Park router tool to the housing.
02. At the same time, pull the shifter housing
out of the head tube port while pushing the
seatpost housing into the seat tube until
the double barb exits the head tube.
SIFTERPush the shifter housing into the lower
head tube port on the non-drive side.
Feed the housing back to the ports on
the rear triangle and eventually out near
the drive-side dropout.
01. YRALIC SETPSRoute a section of shifter housing through the frame using the steps described in Standard Setups. Connect the double-barb to the
shifter housing and the seatpost housing
at the seat tube.
BRAEPush the brake line into the frame starting at the
rear triangle, feeding it forward to the ports into
the front triangle and out the head tube.
03.
Use your finger to help push the
housing around the bend in the frame
up into the seat tube.
PAR TOOL SETP1314
SEAT POST ROUTINGSTAAR SETP
01.
With a 5mm allen wrench, remove the main
pivot Collet Wedge Bolt
02.
With a 10mm allen wrench, remove the Main
Pivot Collet Axle. The Collet Nut on the drive
side can remain in the frame.
03.
Rotate your swingarm upwards to access
both grease zerks and expose the whole
Switch Infinity link. With a clean rag and
mild detergent, clean any mud, dust, or
debris off the Switch Infinity Link.
04.
Using a needle-type grease gun, push new
grease into the two Switch Infinity grease
ports until you see grease extruding from
the shaft seals.
05.
Wipe off any excess grease that was
pushed out of the seals.
06.
Lower the swingarm and re-install your Main
Pivot Collet Bolt prepped with Blue 243
Loctite
*Torque to 12 Nm
07.
Install the Main Pivot Collet Wedge and
*Torque to 14 Nm.
15.16.SWITCH INFINITY SERVICE
17.18
TOOLS EEE
YETI TIPSMake sure your tools are in good condition.
A worn allen key can round the hex on a
bolt not allowing for proper torque.
Torque settings are listed throughout the
instructions. It is important to prep all bolt
threads. The instructions denote whether to
use a Loctite compound or grease.
Warning: Service on Yeti bicycles requires special
knowledge and tools. Yeti Cycles recommends that all
service and repairs be performed by an authorized Yeti
Dealer
• 3mm allen key
• 4mm allen keys
• 5mm allen keys
• 6mm allen key
• 10mm allen key
• Guide pin tool (Or two)
• Cassette tool
• Torque wrench
• Grease
• Blue (243) Loctite
01.
All the parts you’ll need to get your SB130/LR
frame assembled. Please refer to the exploded
view later in this manual for more information.
02.
Press the Shock Eyelet Spacer into the rear
shock eyelet using an arbor press or vise.
03.
Apply a light coat of grease to the threads of the
Rear Triangle at the Seat Stay Pivots. Install x
Bearing Lockring (200020311) with a cassette tool.
*Torque to 20 Nm.
04.
Slide 4x Washer 30003014 over 4x M6 Cap
Screw (3000300) and apply Blue Loctite 43
or similar to the threads.
Insert the 4x Cap Screws into the frame and
place a black Infinity Link washer on each bolt.
Orient the washers such that the flat surfaces are
facing the window in the frame where the Switch
Infinity Link is mounted.
FRAME ASSEMBLY
Otros manuales de Accesorios para bicicletas de Yeti
Yeti
Yeti SB140/LR Manual de usuario
Yeti
Yeti ARC Manual de usuario
Yeti
Yeti SB135/LR Manual de usuario
Yeti
Yeti SB160 Manual de usuario
Yeti
Yeti CNC Stylus Manual de usuario
Yeti
Yeti SB100 Manual de usuario
Yeti
Yeti SB150 Manual de usuario
Yeti
Yeti SnowMX CARGORAK Manual de operación y mantenimiento
Yeti
Yeti SB120 Manual de usuario
Manuales populares de Accesorios para bicicletas de otras marcas
Sigma
Sigma BC 16.16 Manual de usuario
Playcore
Playcore Dero Setbacks Manual de usuario
VDO Cyclecomputing
VDO Cyclecomputing x3dw Manual de usuario
Cateye
Cateye RAPID X2 Manual de usuario
buratti meccanica
buratti meccanica Clorofilla Trail Manual de usuario
Shimano
Shimano SG-8R20 Instrucciones de funcionamiento
