Yealink W70B DECT Manual de usuario
Registering Headsets to W70B
Introduction
After registering the headsets to the W70B, you can use them as standalone devices or with a handset registered at the same
base.
•This feature is only applicable to W70B.
•Please make sure the W70B firmware is 146.85.0.40 or later.
•Please make sure the WH62/WH63 firmware is 104.433.0.10 or later.
•Please make sure the WH6X Portable firmware is 19.420.0.10 or later.
•Please make sure the WH6X with Charging Cable firmware is 104.33.0.16 or later.
Registering Headsets to W70B
You can register the following headsets to W70B:
•WH62/WH63
•WH62 Mono Portable/ WH62 Dual Portable/WH63 Portable
•WHM621 with Charging Cable
/WHD622 with Charging Cable
/WHM631 with Charging Cable
Supported Headsets
Registering Headsets to W70B
WH62/WH63 WH62/WH63 Portable
WHM621/WHD622/WHM631 with Charging Cable
•For WH62/WH63, after switch the mode, the base in
this feature will be idle.
•For WH62/WH63 Portable, the WDD60 Dongle in this
feature will be idle.
•The WHM621/WHD622/WHM631 with Charging
Cable is the most suitable series products for this
feature.
Hardware Introduction
Registering Headsets to W70B
PC Button
Voice Button
Phone Button
Call Control Button
Mute Button
This guide will take WH62 as an example.
Switching Headset Modes（*Only Applicable to WH62/WH63)
Registering Headsets to W70B
Description: You can register the headset to the W70B and use it as a stand-alone device or pair the headsets with a handset registered on the W70B.
Switching Method: Hold the Voice button and Phone button of the headset base for 5 seconds. The PC, Voice and Phone button LED indicator on the
headset base will flash for 5 seconds and off. After this, the headsets will not connect to the base; the base can only be used to charge.
LED Indicator Status: When you successfully switch to registration mode, only the Voice button on the base glows white.
Registering the Headset
Registering Headsets to W70B
Before registering the headset, you have to put the base station into registration mode.
Method 1:
Long press the on the base station till the registration
LED flashes.
1Put the W70B into registration mode
Method 2:
①Go to Status Handset & Voip on the W70B web user
interface.
②Click Start Register Handset to put the W70B into the
registration mode.
Registering the Headset
Registering Headsets to W70B
•If the registration is not successful within 2 minutes, the
headset will exit the registration mode and automatically
reconnect to the previously registered Base.
•If the registration is not successful or the reconnection fails
within 10 minutes, the headset will power off and needs to
be restarted.
2
①Reboot the headset and put the headset into the
registration mode according to the following steps.
②After the headset and W70B are all in the
registration mode, the headset will automatically
register to the W70B.
When the Call Control button flashes blue and the
voice prompts “headset connected,” you
successfully register the headset to the base.
Pairing the Headset with a Handset
Registering Headsets to W70B
You can pair the headset with a handset registered on the W70B. The headset will get the same extension number as the handset.
1. On the web user interface, go to Account →Number Assignment. Check the account you want to share with the handset.
The handsets need to be registered on the W70B first.
Using the Headset to Manage Calls
Registering Headsets to W70B
123
Push Retrieve Redial
Scene: If you are using the handset to
answer the call, go to Options →
Push on the handset, you can push
the call to the headset.
After you pair the headset with a handset registered on the W70B, both the headset and handset will ring when receiving an incoming call.
Scene: If you are using the headset to
answer the call, hold the TRAN key
on the handset, you can retrieve the
call to the handset.
Scene: Double press the Call Control
button on the headset. You can
directly call the last call record.
Note: If you had configured the speed
dial number, the headset would dial
out the number when you double-
press the button.
Otros manuales para W70B DECT
6
Tabla de contenidos
Otros manuales de Auriculares de Yealink
Yealink
Yealink YHS34 Lite Duo Manual de usuario
Yealink
Yealink WH67-UC Manual de usuario
Yealink
Yealink YHS32 Manual de usuario
Yealink
Yealink BH72 Manual de usuario
Yealink
Yealink UH36 Mono Manual de usuario
Yealink
Yealink UH38 Mono Manual de usuario
Yealink
Yealink WH6 Series Manual de usuario
Yealink
Yealink WH6 Series Manual de instrucciones
Yealink
Yealink WH63 Manual de usuario
Yealink
Yealink WH6 Series Manual de usuario
Yealink
Yealink YHS32 Manual de usuario
Yealink
Yealink UH38 Mono Manual de usuario
Yealink
Yealink BH71 Manual de usuario
Yealink
Yealink UH37 Mono Manual de usuario
Yealink
Yealink WH62 Mono Manual de usuario
Yealink
Yealink UH34 SE Mono Manual de usuario
Yealink
Yealink UH37 Mono Manual de usuario
Yealink
Yealink WH66 Mono Manual de usuario
Yealink
Yealink WH63 Manual de usuario
Yealink
Yealink WHB660 Manual de usuario
